RACBOX 3.0 inch bi led fog light lens

Contents

RACBOX 3-inch Bi-LED Fog Light Projector Lens User Manual

Model: 3.0 inch bi led fog light lens

1. Setup and Installation

This product is an auxiliary accessory for automotive lighting, intended for normal replacement and upgrade of original car lights. Please read all instructions carefully before installation.

1.1 Safety Warnings

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture during installation.

1.2 Installation Steps

  1. Turn off the engine and disconnect the vehicle battery to prevent short circuits.
  2. Locate the original fog light position on the front bumper.
  3. Remove the screws, clips, or cover panel to access the fog light housing.
  4. Unplug the wiring connector from the stock fog light.
  5. Remove the original fog light assembly from the bumper.
  6. Install the new fog light assembly into the mounting position.
  7. Secure the fog light with screws or clips to ensure firm installation.
  8. Connect the wiring harness plug correctly. If the light does not work, reverse the polarity.
  9. Reinstall the bumper cover or panel.
  10. Test the fog light function to ensure normal operation.

1.3 Wiring Connection Guidelines

Wiring Connection Diagram
Figure 1: Wiring Connection Guidelines. The diagram shows connections for Positive Electrode, Negative Electrode, and High Beam.

1.4 Adjustable Height

The fog light features an adjustable height nut to fine-tune the lamp's vertical aiming. Rotate the adjusting nut to move the light beam up or down as needed.

Adjustable Height Nut
Figure 2: Adjustable Height Nut. Rotate the nut to adjust the lamp's height, influencing the beam's vertical position (Up/Down).

2. Operating Instructions

This Bi-LED fog light provides both low beam and high beam functionalities for enhanced visibility in various driving conditions.

2.1 Low Beam Function

The low beam provides a wide, flat light pattern designed to illuminate the road directly in front of your vehicle without blinding oncoming traffic. It is ideal for normal driving conditions and light fog.

2.2 High Beam Function

The high beam provides a more focused and intense light pattern, extending visibility further down the road. This mode is suitable for driving in very dark conditions or dense fog where maximum illumination is required, provided there is no oncoming traffic.

Low Beam and High Beam Comparison
Figure 3: Comparison of Low Beam (wide spread) and High Beam (focused intensity) light patterns.

2.3 Product Demonstration Video

For a visual demonstration of the product's features, including its rotation and light patterns, please watch the official product video:

Video 1: Product overview and light pattern demonstration.

3. Maintenance

The RACBOX Bi-LED Fog Light is designed for durability and minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

  • Cleaning: Periodically clean the lens with a soft, damp cloth to remove dirt, dust, and road grime. Avoid abrasive cleaners or materials that could scratch the lens.
  • Inspection: Regularly check the wiring connections to ensure they are secure and free from corrosion. Inspect the housing for any signs of damage.
  • Durability: The fog light has an IP67 waterproof rating, meaning it is protected against dust ingress and can withstand temporary immersion in water. This ensures reliable operation in various weather conditions, including rain, snow, fog, and dusty environments.
Built Tough - Weather Resistance
Figure 4: Built Tough design highlighting resistance to Rainy, Snow, Foggy, and Dusty conditions.

4. Troubleshooting

If you encounter issues with your fog lights, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Light does not turn onIncorrect wiring polarity; Loose connection; No power supply.Reverse wiring polarity if necessary; Ensure all connections are secure; Check vehicle's fuse box for power supply.
Light is dim or flickersInsufficient voltage; Loose connection; Faulty LED driver.Verify vehicle's voltage supply (DC9-16V); Secure all connections; Contact support if LED driver is suspected to be faulty.
Uneven light patternImproper aiming; Obstruction on lens.Adjust the lamp's height using the adjustable nut; Clean the lens thoroughly.

5. Specifications

Detailed technical specifications for the RACBOX 3-inch Bi-LED Fog Light Projector Lens:

FeatureSpecification
Model Name3.0 inch bi led fog light lens
Item TypeFog Lamp Assembly
Beam PatternHigh-Low Beam
Color Temperature6000K White
LensUV-proof HD Glass Lens
Light Source3570W Big Chip LEDs
Material HousingDie-cast Aluminum 6063
Input VoltageDC9-16V (12 V)
Power (Wattage)High beam 45W, Low beam 35W
Lumen10000LM
Waterproof RateIP67
Item Diameter3inch
Special FeaturesHigh low beam
OriginMainland China

5.1 Product Dimensions

Product Size Diagram
Figure 5: Product Size Diagram. Dimensions include 88mm/3.46in (width), 128mm/5.04in (height), 67mm/2.64in (depth), and front face diameter of 100mm/3.94in with a lens diameter of 50mm/1.97in.

6. Warranty and Support

6.1 Standard Warranty

RACBOX represents and warrants to the first end-user (End-User) of the Product that the Product shall materially conform to RACBOX's published specifications in the user manual, subject to the terms and conditions below.

  • Warranty Period: One Year (12 Months) from the date a new product is first delivered to the End-User after being purchased.
  • What is Covered: The Standard Warranty provides support for manufacturing defects of components or workmanship. Customers will be covered for replacement parts, partial refund, or full refund during the Warranty Period.
  • What is NOT Covered: The Warranty does not cover any damage due to abuse, wrong installation, neglect or misuse, extreme environment, unusual physical or electrical stress or interference, exposure to flooding, fire, or electrical problems associated with incoming power or other acts not the fault of Racbox. The Warranty does not cover accessory parts. Racbox is not responsible for damage arising from end-user error and failure to follow instructions relating to Product's use.
RACBOX Warranty Details
Figure 6: RACBOX Warranty information detailing Standard Warranty and Warranty Period.
RACBOX Warranty Coverage
Figure 7: RACBOX Warranty details on what is covered, what is not covered, and how to get service.

6.2 How to Get Warranty Service

If you are within our limited warranty and need to request a replacement part, please use the information below. We are here to help solve problems! If you have any other questions feel free to contact our customer support, either by phone, email, or through our Live Support system.

6.3 Manufacturer & EU Representative Information

  • Manufacturer: Guangzhou Bai Ji Tun Trading Co., Ltd, C116, No. 1489, Fanghua Road Baiyun Guangzhou, tdlaccount@126.com
  • EU Authorized Representative: APEX CE SPECIALISTS LIMITED, UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND, info@apex-ce.com

7. User Tips

Based on general best practices for automotive fog lights, consider the following tips:

  • Aiming: Proper aiming of fog lights is crucial. Ensure they are aimed low and wide to illuminate the road surface and edges without reflecting glare back into your eyes, especially in dense fog.
  • Wiring: Double-check all wiring connections for tightness and proper insulation to prevent shorts and ensure consistent performance.
  • Regular Checks: Periodically check the functionality of both low and high beams, especially before driving in adverse weather conditions.

8. Frequently Asked Questions (FAQ)

Q1: Are these fog lights compatible with my vehicle?

A1: This product is designed for a wide range of vehicles. Please refer to the product description for a detailed compatibility list. It is recommended to compare the dimensions and mounting type with your vehicle's original fog lights before purchase.

Q2: Do I need any special tools for installation?

A2: Standard automotive tools such as screwdrivers, wrenches, and possibly trim removal tools may be required, depending on your vehicle's specific bumper design.

Q3: Can I use these fog lights as daytime running lights (DRL)?

A3: While these lights are bright, their primary function is as fog lights with distinct low and high beam patterns. Check local regulations regarding the use of fog lights as DRLs.

Q4: How do I switch between low and high beam?

A4: The switching mechanism is typically controlled by your vehicle's existing fog light wiring and switch. Ensure the high beam wire is correctly connected as per the wiring guidelines.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.