Godox AD800Pro

Contents

Godox AD800Pro All-in-one Outdoor Flash Instruction Manual

Your comprehensive guide to setting up, operating, and maintaining your Godox AD800Pro flash unit.

Important Safety Instructions

This product is a professional photographic equipment, to be operated by professional personnel only.

The following basic safety precautions must be followed when using this product:

  1. Carefully read and fully understand the instruction manual before use and strictly follow the safety instructions. Failure to do so may result in death, serious injury, damage to the product, or other property damage.
  2. High voltage exists when the flash is powered on. Internal capacitors will remain charged for some time after power off.
  3. This product is a professional lighting fixture, children are prohibited from using it. Children must be closely supervised by adults when approaching the fixture, to prevent collisions with the fixture or unauthorized use that could cause personal injury.
  4. This is not an ordinary lighting fixture and must not be used for general illumination. Anyone with a history of eye damage or sensitivity should avoid using this fixture or looking directly at it.
  5. Extreme caution must be exercised when using it, do not touch high-temperature parts such as flash tubes and surrounding metal components to avoid burns.
  6. Do not point the flash directly at the eyes (especially baby's eyes) under any circumstances, as this could impair vision in a short time. Turn off immediately if discomfort occurs, stop using, and seek medical attention promptly.
  7. If the flash tube is damaged, stop using it immediately and contact the manufacturer, service agent, or qualified repair personnel for a replacement to prevent accidents.
  8. Do not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use after repairs.
  9. Disconnect power source or remove batteries (if it has one) before replacing flash tube, protective glass, or fuses. Allowing 10 minutes to cool before replacing flash tube, and wear insulated or heat resistant gloves when operating.
  10. Turn off power before connecting or disconnecting plugs from outlets. Ensure plugs are fully inserted when connecting.
  11. Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid touching the internal electronic components and getting an electric shock.
  12. Some products have long power cords, please place them properly to avoid contact with heat sources or tripping others. It is recommended to use the original power cord. Damage caused by non-original cords is not covered by the warranty.
  13. Unplug the equipment power plug from the power socket before cleaning or maintenance. Do not pull the power cord forcibly, use both hands to hold the plug end and pull it out.
  14. This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids. It should be installed in a ventilated and dry location and avoid using in rainy, humid, dusty, or overheated environments. Do not place items above the device or allow liquids to flow into it to prevent danger.
  15. Do not disassemble without authorization. If the product malfunctions, it must be inspected and repaired by our company or authorized repair personnel.
  16. Before storing the device, ensure it has completely cooled down and the power cord is unplugged, then put it in the protective case or a ventilated dry location.
  17. Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.
  18. Do not use or store this device in potentially explosive environments.
  19. Do not cover the heat dissipation port!
  20. Do not use accessories not approved by our company, as this may cause fire, electric shock or personal injury.
  21. Clean gently with a dry cloth. Do not use a wet cloth as it may damage the device.
  22. Some products are equipped with protective covers that must be removed before use.
  23. This instruction manual is based on rigorous testing. Changes in design and specifications are subject to change without notice. Check official website for latest instruction manual and product updates.

Battery Safety Warnings

Some products are powered by lithium batteries. The following are the storage recommendations:

  • Charge the battery to about 50% before storage. Charge it to about 50% at least every six months. Failure to perform maintenance charging over an extended period may cause the battery to suffer permanent performance degradation or even become unusable due to excessive discharge.
  • Removable batteries should be stored separately. The storage temperature should be between 0°C and 40°C.
  • Do not disassemble, crush, or puncture the battery.
  • The battery is not waterproof, do not immerse it in fog or water.
  • Avoid short-circuiting the battery contacts.
  • Do not expose the battery to or put it into fire.
  • Do not expose the battery to temperatures above 60°C.
  • Keep out of reach of children.
  • Protect the battery from excessive shock or vibration.
  • Do not use a damaged battery.
  • If the battery leaks, avoid contact with the leaking fluid.
  • If the battery fluid comes into contact with your eyes, immediately rinse with water for at least 15 minutes. Lift your eyelids until there are no signs of fluid and seek medical attention promptly.
  • Confirm and comply with all relevant local laws and regulations when handling any batteries.

CAUTION

Hot surface. Do not touch. Burned fingers when handling the parts. Wait one-half hour after switching off before handling parts.

What's Inside the Box

Upon opening your Godox AD800Pro package, you should find the following components:

Contents of the Godox AD800Pro package, showing the flash body, flash tube, battery, adapter, power cord, reflector, and reflector protection cover.
Contents of the Godox AD800Pro package, showing the flash body, flash tube, battery, adapter, power cord, reflector, and reflector protection cover.
  • Flash Body x 1
  • Flash Tube x 1
  • Battery x 1
  • Adapter x 1
  • Power Cord x 1
  • Reflector x 1
  • Reflector Protection Cover x 1
  • Instruction Manual x 1

Parts Identification

Familiarize yourself with the different parts of your AD800Pro flash unit:

Diagram of the Godox AD800Pro flash unit with numbered parts, including the flash tube, color screen, menu/mode/set buttons, select dial, power switch, modeling lamp button, bracket locking knob, handle, accessory locking pusher, USB-C port, sync cord jack, group indicators, photocell sensor, battery indicator button, battery charging port, battery level indicator, battery detaching pusher, and reflector.
Overview of the Godox AD800Pro flash unit and its main components.
  1. Flash Tube
  2. Color Screen
  3. MENU Button
  4. MODE Button
  5. Select Dial
  6. SET Button
  7. Power Switch/Test Button
  8. Modeling Lamp Button
  9. Bracket Locking Knob
  10. Handle Fixing Fastener
  11. Handle
  12. Accessory Locking Pusher
  13. USB-C Port (firmware upgrade/insert FR433 receiver)
  14. 3.5mm Sync Cord Jack
  15. Group Indicator ×2
  16. Photocell Sensor
  17. Battery Indicator Button
  18. Battery Charging Port
  19. Battery Level Indicator
  20. Battery Detaching Pusher
  21. Reflector

Setup and Installation

1. Mounting the AD800Pro on a Light Stand

Securely attach the flash unit to a compatible light stand for stable operation.

Video: Demonstrates mounting the AD800Pro flash unit onto a light stand.

2. Installing the Battery

The AD800Pro uses a detachable lithium battery pack. Ensure it is correctly installed before use.

Video: Shows the process of installing the battery into the AD800Pro.

Loading: Match the battery's groove with the main battery compartment's ridge. Push down the battery pack until it is locked.

Unloading: Press the battery detaching pusher and push the battery pack upward at the same time to unload it.

3. Installing the Flash Tube and Reflector

The flash tube and reflector are crucial for light output and shaping. Handle them with care.

Video: Illustrates how to install the flash tube and reflector onto the AD800Pro.

Installing the Reflector: Insert the reflector into the accessory mount, press and hold, then rotate clockwise. The accessory locking pusher will lock up.

Disassembling the Reflector: Press down the accessory locking pusher, rotate the reflector anticlockwise to unlock.

Installing the Flash Tube: Press down the accessory locking pusher, remove the reflector or other accessories. Match the flash tube in the tube socket and push until it is securely seated into the socket.

Note: Please power off and wear gloves for the above operations.

4. Adjusting the Flash Angle

Adjust the flash head to direct light as needed for your shot.

Video: Demonstrates how to adjust the angle of the AD800Pro flash head.

1. Rotate the handle anticlockwise to unlock it, adjust the flash body for the desired angle, then rotate the handle clockwise to tighten.

2. If the handle collides with the flash body in rotation, press the handle fixing fastener and pull out the handle, then repeat step 1 after stretching out a few distance.

Operating Modes

1. Power On/Off

To power on the device, long press the power switch button until the unlock icon is displayed on the panel, then rotate the select dial clockwise. To power off, long press the power switch button until the panel blacks out.

Video: Shows how to power on the AD800Pro and unlock the screen.

Note: Turn off the device if it will not be used for an extended period. This device is designed with an automatic power off function, which can be set in menu settings.

2. M (Manual) Flash

In Manual mode, you control the flash output directly. The flash output is adjustable from 1/1 full power to 1/512 power with 0.1 step increment. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output.

Video: Demonstrates setting the flash to Manual (M) mode.

Switch to M mode: Press the MODE button to switch to M mode; the screen will display < M > icon.

Power Adjustment: Turn the select dial to choose a desired flash output amount.

3. Multi: Stroboscopic Flash

With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture multiple images of a moving subject in a single photograph. You can set the flash output, number of flashes, and flash frequency (number of flashes per sec. expressed as Hz).

Video: Shows how to set the flash to Multi (Stroboscopic) mode.

  1. Press the MODE button so that < Multi > is displayed, turn the select dial to choose a desired flash output.
  2. Press the SET button and turn the select dial to set the number of flashes.
  3. Press the SET button and turn the select dial to set the flash frequency.

Calculating the Shutter Speed: During stroboscopic flash, the shutter remains open until the firing stops. Use the formula: Number of Flashes / Flash Frequency = Shutter Speed. For example, if the number of flashes is 10 and the firing frequency is 5 Hz, the shutter speed should be at least 2 seconds.

4. TTL Auto Flash

In TTL mode, the camera's metering system detects the flash reflected from the subject and automatically adjusts the flash output so that the subject and background are evenly exposed. TTL mode is only available when the wireless function is on.

Video: Demonstrates setting the flash to TTL Auto Flash mode.

Switch to TTL mode: Press the MODE button to switch to TTL mode; the screen will display <TTL> icon.

5. High-Speed Sync (HSS)

High-speed sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.

Video: Shows how to enable High-Speed Sync (HSS) on the AD800Pro.

Press the MENU button to enter menu interface, turn the select dial and press the SET button to enter high speed sync and turn it on. Then press MENU button to return to the main interface; the HSS icon <H> can be seen on the panel.

  • If you set a shutter speed that is the same as or slower than the camera's maximum flash sync speed, <H> will not be displayed in the viewfinder.
  • With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
  • To return to normal flash, turn off the high-speed sync function in menu settings. Then <H> will disappear.
  • Multi flash mode cannot be set in high-speed sync mode.
  • Over-temperature protection may be activated after 64 consecutive high-speed sync flashes.

Wireless Control (2.4G Transmission)

The AD800Pro adopts Godox 2.4G wireless X system, offering good compatibility with other Godox products. It can automatically switch to receiver unit according to the transmitter unit instead of setting manually. Compatible cameras include Canon, Nikon, Sony, OM SYSTEM, Panasonic, Fujifilm, Pentax, Leica, etc. As a receiver unit, AD800Pro can be controlled by XProII, X3, X2T, V1Pro, V1, V860III series transmitter units.

1. Wireless Sync with X3Pro (One-Tap Sync)

The X3Pro trigger offers a convenient one-tap sync feature for quick setup.

Video: Demonstrates one-tap wireless sync using an X3Pro trigger.

Wireless Sync (Take X3 flash trigger as an example):

  1. Turn off the camera and mount the flash trigger on camera hot shoe. Then, power on the flash trigger and the camera.
  2. Slide the screen of X3 down from the top to display <Setting>, press <Setting> to enter C.Fn. menu, then press <Wireless> and select <Wireless Sync>.
  3. Press the MENU button of AD800Pro to select wireless and turn it on, then turn the select dial to select <Wireless Sync>.
  4. Their CHs and IDs will automatically be set to the same.
  5. Set the flash mode and output power level of groups on the flash trigger.
  6. Press the trigger button on flash trigger or camera shutter to trigger.

2. Manual Channel Setup for Wireless Triggering

If one-tap sync is not available or you prefer manual control, you can set the wireless channel and group manually.

Video: Illustrates manual channel and group setup for wireless triggering.

Turn on wireless: Press the MENU button to enter menu interface, turn the select dial and press the SET button to enter wireless and turn it on, set the channel, group and ID same as the transmitter unit. Press the MENU button twice to return to the main interface.

Setting the Communication Parameters: If there are other wireless flash systems nearby, you can change the channel to prevent signal interference. The channels of the transmitter unit and the receiver unit(s) must be set to the same.

Parameter Setting
Wireless On/Off
Channel 1-32
Group 0-9, A-F
ID Off, 1-99
Wireless Sync Approx. 100m wireless transmission

3. Wireless Triggering with FT433 Trigger

The FT433 trigger system provides enhanced signal stability and anti-interference capabilities.

Video: Demonstrates wireless triggering using the FT433 trigger.

Operation Instructions:

  1. Turn off the flash trigger, camera and flash, mount the transmitter FT433 on camera hot shoe, insert the receiver FR433 into the USB-C port of AD800Pro. Rotate the antenna out from the top of the transmitter and receiver. Then, power on the flash trigger, camera and flash.
  2. Set FT433: Press the [MENU button] and select <(())> to set channel and ID. Then press the [MENU button] to return the main interface. Press [MODE-LOCK button] to set flash trigger mode, rotate the select dial to set flash trigger level.
  3. Set AD800Pro: Press the [MENU button] to enter menu interface, rotate the [select dial] to select wireless, press the<SET button>to enter wireless setting interface, turn on wireless, set the same channel, group and ID to the flash trigger.
  4. Press the camera shutter to trigger and the status lamp of the flash trigger turns red synchronously.

Note: Flash trigger FT433 is sold separately.

4. Optical S1/S2 Secondary Unit

The AD800Pro can function as an optical slave unit, triggered by another flash.

Video: Demonstrates optical S1 triggering.

Video: Demonstrates optical S2 triggering.

Press the MENU button to enter menu interface, rotate the select dial and press the SET button to enter photocell settings, then rotate the select dial can choose among off, S1 and S2.

  • S1 Secondary Unit: The flash can function as an optical S1 secondary flash with optical sensor in M manual flash mode. With this function, the flash will fire synchronously when the main flash fires, the same effect as that by the use of wireless triggers. This helps create multiple lighting effects.
  • S2 Secondary Unit (pre-flash): The flash can also function as an optical S2 secondary flash with optical sensor in M manual flash mode. This is useful when cameras have pre-flash function. With this function, the flash will ignore a single "pre-flash" from the main flash and will only fire in response to the second, actual flash from the main unit.

Note: S1 and S2 optical triggering is only available in M manual flash mode.

Modeling Lamp

The AD800Pro is equipped with a 40W bi-color LED modeling lamp. You can adjust its brightness and color temperature.

Video: Demonstrates adjusting the modeling lamp settings (Continuous, Free, Prop).

Press the modeling lamp button to enter modeling lamp settings, turn the select dial to choose among off/free/prop, then turn the select dial and press the SET button to adjust the parameters. Press the modeling lamp button to return to the main interface.

Level 1 Options Level 2 Options Notes
OFF / Turn off the modeling lamp
FREE 10%-100% (with 1% increment) Brightness range
2800K-6000K (with 100K increment) CCT range
PROP 2800K-6000K (with 100K increment) CCT range, and brightness follows flash power.

Sync Triggering

The AD800Pro can be triggered via a wired connection using its 3.5mm sync cord jack.

Video: Demonstrates syncing the flash via the 3.5mm port.

The sync cord jack is a ⌀3.5mm plug. Insert a trigger plug in and the flash will be fired synchronously with the camera shutter.

Protection Functions

1. Over-Temperature Protection

To prevent overheating and damage to the flash head, the AD800Pro incorporates an over-temperature protection system.

  • To avoid overheating and deteriorating the flash head, do not fire more than 64 continuous flashes in fast succession at 1/1 full power. After 64 continuous flashes, allow a rest time of at least 10 minutes.
  • If you fire more than 64 continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated and make the recycling time over 10 seconds. If this occurs, allow a rest time of about 10 minutes, and the flash unit will then return to normal.
  • When the over-temperature protection is started, a thermometer icon is shown on the screen.

Number of flashes that will activate over-temperature protection:

Power Output Level Number of Flashes
1/180
1/2 (+0.7)105
1/2 (+0.3)128
1/2160
1/4 (+0.3, +0.7)210
1/8 (+0.3, +0.7)375
1/16 (+0.3, +0.7)800
1/32 (+0.3, +0.7)1060
1/64 (+0.3, +0.7)2130

Number of flashes that will activate over-temperature protection in high-speed sync triggering mode:

Power Output Level Number of Flashes
1/164
1/2 (+0.3, +0.7)70
1/4 (+0.3, +0.7)90
1/8 (+0.3, +0.7)115
1/16 (+0.3, +0.7)140
1/32 (+0.3, +0.7)180
1/64 (+0.3, +0.7)210
1/128 (+0.3, +0.7)235
1/256 (+0.3, +0.7)255

2. Other Protections

The system provides real-time protection to secure the device and your safety. The following lists prompts for your reference:

Display Meaning
Error1 A failure occurs on the recycling system so that the flash cannot fire. Please restart the flash unit. If the problem still exists, please send this product to a maintenance center.
Error3 The voltage on two outlets of the flash tube is too high. Please send this product to a maintenance center.
Error9 There are some errors occurred during the upgrading process. Please using the correct firmware upgrade method.

Troubleshooting

If you encounter issues with your Godox AD800Pro, refer to the following common problems and solutions:

The Reason & Solution of Not Triggering in Godox 2.4G Wireless

  1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G wifi router, Bluetooth, etc.)
    • To adjust the channel CH setting on the flash trigger (add 10+ channels) and use the channel which is not disturbed. Or turn off the other 2.4G equipment in working.
  2. Please make sure that whether the flash has finished its recycle or caught up with the continuous shooting speed or not (the flash ready indicator is lightened) and the flash is not under the state of over-heat protection or other abnormal situation.
    • Please downgrade the flash power output. If the flash is in TTL mode, please try to change it to M mode.
  3. Whether the distance between the flash trigger and the flash is too close or not (< 0.5m).
    • Please turn on "short distance wireless mode" of the flash trigger.
    • X1 Series: Press and hold the triggering button then turn on the device, until the indicator blinks twice.
    • XPro and X2T Series: Please set the C.Fn-DIST to 0-30m.
    • X3 Series: Please set the triggering distance to 0-30m.
  4. Whether the flash is in the low battery states or not.
    • Please charge or replace the battery in time, and ensure both devices have enough battery power.
  5. The flash trigger's firmware is an older version
    • Please upgrade the firmware of the flash trigger referring to the instruction manual for specific firmware upgrades.
  6. The camera's firmware is an older version
    • Please upgrade the firmware of the camera referring to its instruction manual.

User Tips

  • Always ensure the battery is fully charged before important shoots to avoid interruptions.
  • When using multiple flash units, utilize the distinct color group indicators for quick identification and adjustment.
  • For outdoor shooting in bright sunlight, leverage the 800Ws output and HSS mode to overpower ambient light effectively.
  • Regularly check for firmware updates for both the flash and your camera/trigger to ensure optimal performance and compatibility.
  • Experiment with the modeling lamp's 'FREE' and 'PROP' modes to understand how they can assist in pre-visualizing lighting and adjusting to flash output.

Technical Specifications

Feature Specification
ModelAD800Pro
Wireless Receiver Unit ModeWireless Mode (compatible with Canon E-TTL II, Nikon i-TTL, Sony, OM SYSTEM, Panasonic, Fujifilm, Leica, Pentax)
Flash ModeWireless off: M/Multi; Wireless receiver mode: TTL/M/Multi
Guide No. (1/1 step)110 (ISO 100, in meters, with efficient reflector)
Flash Duration (t=0.1)Normal: 1/350s~1/11400s; Color: 1/350s~1/9220s; Freeze: 1/5020s~1/35710s
Power (1/1 step)800Ws
Power Output10 steps: 1/512~1/1 (with 0.1 increment each step) Note: 9 steps in CCT mode
Stroboscopic FlashProvided (up to 100 times, 100Hz)
Sync ModeHigh-speed sync (up to 1/8000 seconds), first-curtain sync, and second-curtain sync
Delay Flash0.01 ~ 30s
Mask✓
Fan✓
Beep✓
Flash Duration Indication✓
PhotocellS1/S2/OFF
DisplayColor screen
Modeling Lamp
Max. Input Power40W
Brightness Range10%-100%
CRIAverage≥97
TLCIAverage≥98
CCT2800K-6000K
Wireless Flash (2.4G transmission)
Wireless FunctionReceiver, Off
Controllable Receiver Groups16: 0-9, A-F
Transmission RangeApprox. 100m
Channels32:1-32
ID01-99/OFF
Power Supply
Power SupplyLithium battery (28.8V/2900mAh)
Full Power FlashesApprox.300
Recycle TimeQuickest approx. 0.01s ~ 1.5s
Battery Level Indicator✓
Power SavingAuto off function is available in menu settings (30min to 120min of idle use)
Sync Triggering Mode3.5mm sync cord
Flash Tube Color Temperature5800±200K
Dimensions and Weights
Dimension (with battery, flash tube and reflector)≈ 4.96"×6.1"×13.5"
Net Weight (with battery, flash tube and reflector)≈ 3.7kg

Specifications and data may subject to changes without notice.

Firmware Upgrade

Keeping your AD800Pro's firmware updated ensures optimal performance and compatibility.

  • This flash supports firmware upgrade through the USB-C port. Update information will be released on our official website.
  • Please use an USB-C cable (sold separately) for firmware upgrade.
  • As the firmware upgrade needs the support of Godox G3 software, please download and install the software from Godox official website (https://www.godox.com.cn/firmware-G3/) before upgrading. Then, choose the related firmware file.
  • Please refer to the latest electronic version of the instruction manual.

Warranty and Support

The warranty period for this device as a whole is one year. Consumables (such as batteries), adapters, power cords, and other accessories are not covered by the warranty.

Unauthorized repairs will void the warranty and will incur charges. Failures from improper operation are not covered under warranty.

How to Get Maintenance Service:

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide a valid warranty card. If you cannot provide a valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Contact Information:

  • GODOX Photo Equipment Co., Ltd.
  • Address: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao'an District, Shenzhen 518103, China
  • Tel: +86-755-29609320 (8062)
  • Fax: +86-755-25723423
  • E-mail: godox@godox.com
  • Website: www.godox.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.