liitokala LiFePO4-BMS

Contents

LiitoKala Smart BMS User Manual

Models: 4S 12V, 8S 24V (100A/200A variants)

1. Product Overview

The LiitoKala Smart Battery Management System (BMS) is designed for 4S 12V and 8S 24V LiFePO4 and Li-ion battery packs. It provides comprehensive protection and monitoring features to ensure the safe and efficient operation of your battery system. Key features include Bluetooth APP status monitoring, UART communication, and robust hardware protection against various electrical faults.

LiitoKala 4S-12V 200A Smart BMS with Bluetooth APP monitoring and full hardware protection.

Figure 1: LiitoKala 4S-12V 200A Smart BMS with Bluetooth APP monitoring and full hardware protection.

This BMS is suitable for a wide range of applications requiring reliable energy storage, including electric scooters, drones, power tools, tricycles, cars, RVs, and portable power stations.

Wide range of application for LiitoKala BMS, including electric scooters, drones, power tools, tricycles, cars, RVs, and portable power stations.

Figure 2: Wide range of application for LiitoKala BMS.

2. Setup Instructions

2.1 Wiring the BMS

Proper wiring is critical for the safe and correct operation of the BMS. Refer to the diagram below for the common port wiring method. Ensure all connections are secure and correctly polarized.

BMS Wiring Diagram (Common Port) showing connections for lithium battery pack, motor/load, charger, and BMS terminals (B+, C-, B-).

Figure 3: BMS Common Port Wiring Diagram. Connect the lithium battery pack, motor/load, and charger to the respective B+, C-, and B- terminals. The sampling sort wires connect to the wiring interface.

Important Note: Wiring methods can vary between manufacturers. Always use the supporting wiring harness provided with this protection board. Using incompatible wiring may lead to malfunctions and will void return or replacement eligibility.

The BMS board includes several interfaces for communication and sensing:

  • UART Communication mode: For data exchange.
  • Temperature sensor interface: For monitoring battery temperature.
  • Voltage acquisition line interface: For monitoring individual cell voltages.
  • KEY: key switch: For controlling the BMS.
Product Description diagram showing UART Communication mode, Temperature sensor interface, Voltage acquisition line interface, and Key switch on the BMS board.

Figure 4: BMS board interfaces.

2.2 APP Installation and Connection

The LiitoKala Smart BMS utilizes the "RBT BMS" mobile application for status monitoring and parameter configuration. The app is available for iOS and Android devices.

  1. Download the APP:
    • Method 1 (QR Code): Scan the QR code below using your smartphone to download and install the "RBT BMS" app.
    • QR code for downloading the Rabbit BMS APP.

      Figure 5: QR code for "RBT BMS" APP download.

    • Method 2 (App Store): Search for "RBT BMS" in the Apple App Store (for iOS) or Google Play Store (for Android) and install the application.
  2. Connect to the APP:
    • Enable Bluetooth and location services on your smartphone.
    • Open the "RBT BMS" app and grant necessary permissions for location and Bluetooth access.
    • The app will automatically search for available BMS devices. Select your device from the list and tap "Pair" or "Connect".
Bluetooth connection screen in the Rabbit BMS app, showing options for BLE Connection, 4G Connection, Scan, and Display.

Figure 6: Bluetooth connection interface in the "RBT BMS" app.

2.3 Initial Parameter Settings

After successfully pairing the BMS with the app, it is crucial to configure the initial parameters for accurate operation.

  1. Battery Pack Settings:
    • Navigate to the "Settings" section in the app.
    • Select "Battery Pack Settings" and then "Modify Configuration".
    • Enter the password (original password: 2468).
    • Set the actual capacity of your battery pack accurately. This is essential for correct State of Charge (SOC) display. After setting, the SOC will automatically calibrate during subsequent use.
  2. AFE Parameter Settings:
    • From the main operations screen, select "AFE Parameter Settings" and then "Modify Configuration".
    • Enter the password (original password: 7569).
    • Adjust other parameters according to your specific needs or under the guidance of the manufacturer.
AFE Parameter Settings screen in the Rabbit BMS app, showing options for Charge/Discharge Operation, AFE Parameter Settings, and other settings like Battery Pack Settings.

Figure 7: AFE Parameter Settings interface.

3. Operating the BMS

Once configured, the "RBT BMS" app allows you to monitor your battery pack data in real-time and control various operations.

3.1 Real-time Monitoring

The app's main interface displays real-time data such as battery voltage, current, temperature, and State of Charge (SOC). This allows for continuous oversight of your battery's performance.

3.2 Charge/Discharge Control

Within the app, you can manage charging and discharging operations. Options typically include:

  • Charging on/off: Enable or disable charging.
  • Discharge on/off: Enable or disable discharging.
  • Active balancing on/off: Control the active cell balancing feature.
  • Heating on/off: If your BMS supports heating, you can control it here.
  • Force Start/Stop: Initiate or terminate operations manually.

3.3 Advanced Parameter Settings

Beyond initial setup, the app provides access to advanced settings for fine-tuning your BMS performance. These include:

  • Battery Pack Settings
  • Current Calibration
  • Heater Parameter Settings
  • Active Balance Parameter Settings
  • Charge Parameter Settings
Battery Parameter Settings screen in the Rabbit BMS app, highlighting Battery Pack Settings, Current Calibration, Heater Parameter Settings, Active Balance Parameter Settings, and Charge Parameter Settings.

Figure 8: Battery Parameter Settings interface.

4. Maintenance

To ensure the longevity and accurate performance of your LiitoKala Smart BMS and battery pack, follow these maintenance guidelines:

  • SOC Calibration: When the BMS is first powered on, the State of Charge (SOC) display on the main status interface is for reference only. For accurate SOC readings, you must set the correct actual cell capacity in the "Battery Pack Settings" and then perform a deep charge and discharge cycle (allowing overcharge and over-discharge protection to activate) to calibrate the SOC value.
  • Charging Practices: Always adhere to safe charging practices. Be mindful of potential fire risks associated with lithium-ion batteries and strictly follow the instruction manual for charging procedures.
  • Storage: When storing the battery pack with the BMS, ensure it is kept in a suitable environment within the recommended temperature range (-40 to 85°C).
  • Disposal: For end-of-life disposal, consult your local authority's website for information on safe and environmentally responsible disposal of lithium-ion batteries in accordance with applicable legal requirements.

5. Troubleshooting

If you encounter issues with your LiitoKala Smart BMS, consider the following common problems and solutions:

  • Inaccurate SOC Display: If the State of Charge (SOC) appears incorrect, ensure that the actual capacity of your battery pack was accurately set during the initial setup in the "Battery Pack Settings" of the app. Performing a deep charge and discharge cycle after setting the capacity can help calibrate the SOC.
  • Bluetooth Connection Issues:
    • Verify that Bluetooth and location services are enabled on your smartphone.
    • Ensure the "RBT BMS" app has the necessary permissions to access Bluetooth and location.
    • Check if your smartphone's operating system version is compatible with the app. Some users have reported issues with app functionality on newer phone models. Try using a different device if available to isolate the problem.
    • Restart both the BMS (by disconnecting and reconnecting the battery) and your smartphone.
  • BMS Malfunction After Wiring: If the BMS does not function correctly immediately after wiring, double-check all connections against the provided wiring diagram (Figure 3). Incorrect wiring, especially using non-standard or incompatible wiring harnesses, can cause damage or prevent proper operation.
  • General Performance Issues: If you experience unexpected behavior, review the AFE Parameter Settings and other advanced settings in the app. Ensure these parameters are configured correctly for your specific battery type and application. If unsure, consult the manufacturer's guidance.

6. Specifications

The following table details the technical specifications of the LiitoKala Smart BMS:

Table of Product Parameters including Rated charge voltage, Charging current, Discharge current, Overcurrent protections, Equalization functions, and Temperature protections.

Figure 9: Detailed Product Parameters.

General Specifications
Attribute Value
Brand Name liitokala
Model Number LiFePO4-BMS
Type LiFePO4
Nominal Capacity 12V/24V-100A/200A
Voltage 4S-12V/8S-24V
Rated Voltage 3.2V
Origin Mainland China
Certification CE, FCC, RoHS
High-concerned chemical None

7. User Tips

  • Initial SOC Calibration: For the most accurate State of Charge (SOC) readings, ensure you correctly input your battery pack's actual capacity in the app's settings during the first use. Follow this by a full charge and discharge cycle to allow the BMS to calibrate properly.
  • App Compatibility: If you experience issues with Bluetooth connectivity or app functionality, especially on newer smartphone models, verify the app's compatibility with your device's operating system version. Trying the app on a different device might help diagnose the issue.
  • Wiring Verification: Always double-check your wiring against the provided diagram. Incorrect connections are a common source of problems and can prevent the BMS from operating as intended.
  • Parameter Review: If the BMS is not performing as expected, review all configured parameters in the app. Small adjustments can significantly impact performance.

8. Warranty and Support

For detailed information regarding warranty coverage and technical support, please refer to the official product documentation or contact LiitoKala customer service.

A comprehensive user manual in PDF format is available for download. You can access it via the following link: LiitoKala Smart BMS User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.