TOMZN TOVPD1-60-VA

Contents

TOMZN TOVPD1-60-VA DIN Rail Adjustable Over/Under Voltage and Over Current Protective Device User Manual

Model: TOVPD1-60-VA

1. Introduction

The TOMZN TOVPD1-60-VA is an intelligent dual-display voltage and current protector designed for DIN rail mounting. This device automatically monitors the voltage and current in your circuit and will cut off the power supply instantaneously if it detects over-voltage, under-voltage, or over-current faults. This protects connected electrical equipment from potential damage. It features adjustable protection values and automatic recovery.

TOMZN TOVPD1-60-VA Device Front View

Figure 1: Front view of the TOMZN TOVPD1-60-VA device.

2. Safety Information

WARNING: To avoid danger of suffocation, keep any plastic packaging away from babies and children. Do not use this bag in cribs, beds, carriages, or playpens. This bag is not a toy.

  • Always have a qualified electrical professional perform the installation and operation of this device.
  • Do not place the device near flammable materials.
  • Ensure adequate ventilation during operation to prevent overheating.
  • Disconnect the device from power before performing any maintenance or adjustments.
  • Store the device properly when not in use for extended periods.

3. Product Overview and Features

The TOVPD1-60-VA offers comprehensive protection and monitoring capabilities:

  • Over-voltage Protection (OV): Automatically disconnects power if voltage exceeds set limit.
  • Under-voltage Protection (UV): Automatically disconnects power if voltage drops below set limit.
  • Over-current Protection (OCP): Automatically disconnects power if current exceeds set limit.
  • Automatic Recovery: Device automatically restores power once conditions return to normal after a set delay.
  • Voltage Display: Real-time display of current voltage (voltage measurement).
  • Current Display: Real-time display of current draw (current measurement).
  • Adjustable Parameters: All protection thresholds and delay times are user-adjustable.
  • Voltage Calibration (A13): Allows for fine-tuning of voltage readings.
Function Selling Points Icons

Figure 2: Key functions of the device including voltage display, over-voltage, under-voltage, current display, active time adjustable, and automatic recovery.

4. Setup

4.1. Unpacking

Carefully remove the device from its packaging. Inspect for any visible damage. If any damage is found, do not proceed with installation and contact your supplier.

4.2. Mounting

The TOVPD1-60-VA is designed for 35mm DIN rail installation.

  1. Locate a suitable position on your electrical panel's DIN rail.
  2. Align the device with the DIN rail and press firmly until it clicks into place.
  3. Ensure the device is securely mounted and does not wobble.
DIN Rail Mounting Illustration

Figure 3: The device is designed for simple and convenient 35mm standard DIN rail installation and disassembly.

4.3. Wiring

IMPORTANT: All wiring must be performed by a qualified electrical professional. Ensure the main power supply is OFF before starting any wiring work.

  1. Identify the 'IN' (Input) terminals (N and L) and 'OUT' (Output) terminals on the device.
  2. Connect the incoming neutral (N) and live (L) power lines to the 'IN' terminals. When power is input through L and N, screw down to penetrate the insulating layer of the power lines.
  3. Connect the outgoing neutral (N) and live (L) lines to your load (e.g., circuit breaker, appliances) from the 'OUT' terminals.
  4. Ensure all connections are tight and secure to prevent loose contacts and potential hazards.
Wiring Diagram for TOMZN Voltage Protector

Figure 4: Easy wiring diagram showing connection between a power switch, the voltage protector, and an air circuit breaker.

5. Operating Instructions

5.1. Display Elements and Buttons

Device Front Panel with Labels

Figure 5: Front panel showing Volt Display, Current Display, Set button, Adjustment keys, Over Voltage indicator, Under Voltage indicator, Over Current indicator, and Power indicator.

  • Volt Display: Shows the real-time voltage.
  • Current Display: Shows the real-time current.
  • >V (Red LED): Illuminates when an over-voltage condition is detected.
  • <V (Red LED): Illuminates when an under-voltage condition is detected.
  • >A (Red LED): Illuminates when an over-current condition is detected.
  • POWER (Green LED): Illuminates when the device is powered on and operating normally.
  • SET Button: Used to enter the parameter setting mode.
  • Up/Down Adjustment Keys (Green Triangles): Used to navigate through settings and adjust values.

5.2. Setting Parameters

The device allows you to adjust various protection values and delay times. The operation of button setting is simple.

  1. Enter Setting Mode: Press and hold the SET button for a few seconds until the display starts flashing, indicating you are in setting mode.
  2. Navigate Settings: Use the Up and Down adjustment keys to cycle through the parameters (A1 to A13, and OFF).
  3. Adjust Values: When the desired parameter is displayed, press the SET button briefly to select it. Then use the Up and Down keys to change its value.
  4. Confirm Value: Press the SET button again to confirm the new value and move to the next parameter, or wait a few seconds for the device to automatically save and exit.
  5. Exit Setting Mode: To exit settings, either cycle through all parameters until 'End setting' is displayed and press SET, or wait for the device to time out and automatically exit.
Product Setting Flowchart

Figure 6: Flowchart illustrating the product setting parameters (A1-A12, OFF) and how to adjust them.

Parameter List:

ParameterDescriptionRangeDefault
A1Power-on delay time1-500s10s
A2Over-voltage protection value230-300V270V
A3Over-voltage recovery value225-295V250V
A4Over-voltage recovery delay time1-500s30s
A5Over-voltage protection action time0.1-30s0.5s
A6Under-voltage protection value140-210V170V
A7Under-voltage recovery value145-215V190V
A8Under-voltage recovery delay time1-500s30s
A9Under-voltage protection action time0.1-30s0.5s
A10Over-current protection value0.5-40A / 0.5-63A20A / 40A
A11Over-current recovery delay time1-500s30s
A12Over-current protection action time0.1-30s0.5s
A13Voltage calibration+/- 9.5%0%
OFFManual switch (turn off protection)On/OffOn

6. Maintenance

  • Keep the device clean and free from dust. Use a dry, soft cloth for cleaning.
  • Do not use abrasive cleaners or solvents.
  • Ensure adequate ventilation around the device during operation.
  • Regularly check wiring connections for tightness.
  • If the device is not going to be used for an extended period, disconnect it from the power supply and store it in a dry, cool place.

7. Troubleshooting

  • Device not powering on: Check the input power supply and wiring connections. Ensure the main circuit breaker is on.
  • Protection tripping unexpectedly: Verify that the set protection values (over-voltage, under-voltage, over-current) are appropriate for your load and power supply. Check for actual voltage/current fluctuations in your circuit.
  • Display not working: Ensure the device is receiving power. If power is present and the display is still off, the device may be faulty.
  • Device not recovering automatically: Check the recovery delay time settings. Ensure the fault condition has cleared.

8. Specifications

FunctionTechnical ParameterFunctionTechnical Parameter
Input voltageAC 140-300VPower-on delay time1-500s (default 10s)
Over-voltage protection value230-300V (default 270V)Over-voltage recovery value225-295V (default 250V)
Under-voltage protection value140-210V (default 170V)Under-voltage recovery value145-215V (default 190V)
Over-current protection value0.5-40A (default 20A) / 0.5-63A (default 40A)Over-current recovery value0-39.5A / 0-62.5A
Recovery delay time1-500s (default 30s)Action time0.1-30s (default 0.5s)
Power consumption≤2WElectrical and mechanical life≥100,000 cycles
Boundary dimension86×38×68mmWiringOver-entering down-out
Device Dimensions Diagram

Figure 7: Device dimensions: 85mm height, 37.5mm width (front view); 65mm depth, 45mm height from DIN rail (side view).

8.1. Applicable Regulations and Harmonized Standards

  • Low Voltage Directive (LVD) 2014/35/EU
  • Electromagnetic Compatibility (EMC) Directive 2014/30/EU
  • Restriction of the Use of Certain Hazardous Substances (RoHS) Directive 2011/65/EU

9. User Tips

  • Many users find this device easy to set up, configure, and install, making it a straightforward addition to your electrical system.
  • Always double-check your wiring against the diagram before powering on to ensure correct functionality and safety.
  • Take advantage of the adjustable parameters to fine-tune the protection levels to perfectly match the requirements of your specific appliances and electrical environment.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the TOMZN official support channels.

11. Disposal Information

This product contains electronic components and should not be disposed of with general household waste. Please follow local regulations for the disposal of electronic waste. Look for collection points or recycling facilities in your area.

Recycling Symbol for Electrical and Electronic EquipmentRecycling Symbol for Packaging

Recycle this product and its packaging responsibly.

© TOMZN. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.