HamGeek B205Mini

Contents

HamGeek B205Mini SDR User Manual

Model: B205Mini

1. Introduction

Thank you for purchasing the HamGeek B205Mini Software Defined Radio (SDR). This manual provides essential information for the safe and effective use of your device. The B205Mini is a fully integrated single-board general-purpose SDR peripheral platform, offering continuous frequency coverage from 70 MHz to 6 GHz. It is designed for low-cost experimentation, integrating an RFIC direct-conversion transceiver (AD9361) with up to 56 MHz of real-time bandwidth, a reprogrammable FPGA, and fast USB 3.0 connectivity with convenient bus power.

2. Product Overview

2.1 Device Features

  • Fully integrated USRP device with continuous RF coverage from 70 MHz to 6 GHz.
  • Full-duplex operation with real-time bandwidth up to 56 MHz (61.44 MS/s quadrature).
  • Fast and convenient Super-Speed USB 3.0 connection.
  • Open and reconfigurable FPGA (ZYNQ XC7A020).
  • Early prototype design platform for ADI's AD9361 RFIC, a fully integrated direct-conversion transceiver.

2.2 Package Contents

Please check the package for the following items:

  • HamGeek B205Mini motherboard with heatsink and protective case (pre-assembled) x 1
  • TQTT rubber antenna x 3
  • Micro-USB 3.0 data cable x 1
  • RF cable (female-female connector) x 3

2.3 Device Layout

Top view of HamGeek B205Mini SDR with labels

Figure 1: Top view of the HamGeek B205Mini SDR. Labels include PWR (Power indicator), USB3 (USB 3.0 port indicator), TRX (Transmit/Receive port), RX2 (Receive port 2), REF (Reference clock port), and LOCK indicators for REF and FPGA.

Side view of HamGeek B205Mini SDR showing USB port

Figure 2: Side view of the HamGeek B205Mini SDR, highlighting the USB 3.0 port and adjacent PWR indicator.

Bottom view of HamGeek B205Mini SDR

Figure 3: Bottom view of the HamGeek B205Mini SDR, showing the protective casing secured with four screws.

3. Safety Information

Before using this product, please read and comply with all safety instructions to prevent damage to the device or personal injury.

3.1 Electrical Safety

  • Use only the power adapter provided with the product or a compliant power supply.
  • If the power cord is damaged, do not continue to use it. Contact support for a replacement.
  • Always disconnect the power before cleaning the device.

3.2 Usage Environment

  • Operating temperature range: -10°C to 40°C (subject to model specifications).
  • Avoid direct sunlight, high temperatures, and dusty environments.
  • Keep the ventilation good and do not block the heat dissipation holes.
  • Do not use in humid environments unless the product specifically states a waterproof rating.

3.3 Operational Safety

  • Do not disassemble or modify the product yourself, as there are no user-repairable parts inside.
  • Prevent liquid from entering the product interior.
  • If the product emits smoke, unusual odors, or abnormal noise, immediately disconnect the power and contact after-sales service.

4. Getting Started (Setup)

4.1 Unpacking Inspection

After opening the package, please check that all items listed in Section 2.2 are complete and undamaged. If you find any items missing or damaged, please contact support immediately.

4.2 First Use

  • Ensure the product is fully charged before use (if applicable, though B205Mini is bus-powered).
  • Check if the power supply voltage (from your USB 3.0 port) is consistent with the product specifications (5V DC).
  • Connect the provided antennas to the TRX, RX2, and REF ports as needed for your application.
  • Connect the HamGeek B205Mini to your computer using the supplied Micro-USB 3.0 data cable.

5. Operation

5.1 Basic Operations

  • Power On/Off: The device powers on automatically when connected to a powered USB 3.0 port. Disconnect the USB cable to power off.
  • Function Selection: Functions are typically controlled via software on your connected computer (e.g., GNU Radio).

5.2 Software Defined Radio Usage

The HamGeek B205Mini is designed for use with various SDR software platforms. It is fully supported and compatible with:

  • GNU Radio: A free and open-source software development toolkit that provides signal processing blocks to implement software radios.
  • OpenBTS: An open-source software implementation of the GSM radio access network, allowing you to build your own GSM base station prototypes.
  • SRSRAN and OAI (OpenAirInterface): Other popular open-source software suites for LTE/5G research and development.

The device features built-in firmware, making it plug-and-play without the need for tedious file replacement.

5.3 Instrument-Specific Instructions (if applicable)

If using the B205Mini for measurement purposes, ensure you understand the measurement safety levels of your setup. Confirm the product's corresponding measurement category (CAT I/II/III/IV) and rated voltage. Do not use it outside the specified range. When measuring an unknown voltage, always start with the highest range.

6. Maintenance and Care

  • Cleaning: Wipe the outer casing with a soft, dry cloth. Do not use chemical solvents, as they may damage the finish.
  • Storage: When not in use for an extended period, clean the device and store it in a cool, dry place away from direct sunlight and extreme temperatures.
  • Battery (if applicable): The B205Mini is bus-powered and does not contain an internal battery.

7. Troubleshooting

If you encounter issues with your HamGeek B205Mini, refer to the table below for common problems and solutions.

ProblemPossible ReasonsSolution
Device does not power onUSB not connected or insufficient power from USB portCheck the USB 3.0 connection; try a different USB 3.0 port or a powered USB hub.
No display/Software errorPoor connection or incorrect software settingsRestart the device (reconnect USB) and check software configuration. Ensure drivers are installed.
Inaccurate measurements (instrument-related)Incorrect range or calibration requiredConfirm the measurement range in your software. Consider professional calibration services if accuracy is critical.
Other faultsHardware malfunction or software conflictContact technical support for further assistance.

8. Specifications

Parameter CategorySpecification
Frequency Coverage70 MHz – 6 GHz (continuous)
Real-time BandwidthUp to 56 MHz (61.44 MS/s quadrature)
ConnectivityUSB 3.0 (Super-Speed)
RFIC TransceiverAnalog Devices AD9361
FPGAZYNQ XC7A020
Operation ModeFull-duplex
DC Voltage Input5 V (via USB 3.0)
ADC Sampling Rate (Max)61.44 MS/s
ADC Resolution12 bits
DAC Sampling Rate61.44 MS/s
DAC Resolution12 bits
LO Accuracy±2 ppm
Output Power (typical)>10 dBm
Noise Figure<8 dB
Operating Temperature-10°C to 40°C
Storage Temperature-20°C to 60°C
Protection LevelIP20 (for indoor use)

9. Frequently Asked Questions and User Tips

9.1 HamGeek B205Mini vs. TinyB210

  • Input/Output: HamGeek B205Mini is Single-Input Single-Output (1R1T), while TinyB210 is Dual-Input Dual-Output (2R2T).
  • Power Amplifier (PA): The B205Mini transmitter is equipped with a Power Amplifier (PA). The TinyB210 does not include an RF amplifier, which results in a very low noise floor and high channel isolation.
  • Clocking: Both B205Mini and TinyB210 feature External Clock (EXT_CLK) input and PPS input. The TinyB210 also includes a GPS module and implements a built-in GPSDO.
  • Firmware: Both devices have built-in firmware, making them plug-and-play without the need for tedious file replacement.

9.2 Software Support

The HamGeek B205Mini fully supports GNU Radio, SRSRAN, and OAI, operating exactly the same as official compatible models.

9.3 RF Power Amplifier (PA) Considerations

Official boards for ADI, such as FMCOMMS2, 3, 5, etc., typically do not come with PAs, as a few dBm input power is often sufficient for RF experiments. While the B205Mini includes a PA, it's important to note that during full-duplex transmission and reception, the presence of a PA can have a significant impact on the receiving end due to potential self-interference.

10. Compliance Information

10.1 CE Declaration of Conformity

This product complies with the essential requirements of the following EU directives:

  • Low Voltage Directive (LVD) 2014/35/EU
  • Electromagnetic Compatibility Directive (EMC) 2014/30/EU
  • RoHS Directive 2011/65/EU

10.2 Waste Electrical and Electronic Equipment (WEEE)

The wheeled bin symbol marked with an X on the product indicates that, according to EU Directive 2012/19/EU, this product must not be disposed of as unsorted municipal waste. It must be collected and recycled separately.

11. Warranty and Support

11.1 Warranty Policy

The product comes with a 12/24 month warranty from the date of purchase (subject to store announcement).

11.2 Technical Support

For detailed technical documentation, calibration certificates, or hard copies of the manual, please contact us via AliExpress internal message or email: hamgeeks@163.com. Response time is typically within 24 hours (working days).

12. Disclaimer

This instruction manual is a general version; the actual product functions and parameters shall prevail. The manufacturer reserves the right to change product designs and specifications without prior notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.