Godox V480

Contents

Godox V480 TTL Camera Flash Instruction Manual

Compact Design, Complete Control

1. Introduction

Thank you for purchasing the Godox V480 TTL Li-ion Camera Flash. This flash unit offers excellent compatibility and convenience for various shooting conditions. Its compact design and comprehensive control features make it a versatile tool for professional results.

For a detailed overview of the product, please refer to the official user manual PDF: Godox V480 User Manual (PDF)

2. Important Safety Instructions

This product is professional photographic equipment and should only be operated by professional personnel.

All transport protective materials and packaging must be removed before use.

Please follow these basic safety precautions:

  • Read the instruction manual thoroughly before use to prevent injury or damage.
  • This product is a professional lighting fixture; children are prohibited from using it. Adult supervision is required if children are nearby.
  • Do not use this fixture for general illumination. Avoid looking directly at the light source, especially if you have eye damage or sensitivity.
  • Exercise extreme caution; do not touch high-temperature parts like flash tubes to avoid burns.
  • Do not point the flash directly at eyes, especially infants', as this can impair vision. Turn off immediately if discomfort occurs.
  • If the flash tube is damaged, discontinue use and contact a service agent for replacement.
  • Stop using immediately if the product shell is cracked to avoid electric shock.
  • This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids. Use in a ventilated, dry location, away from rain, humidity, dust, or overheating.
  • Do not disassemble without authorization. Repairs must be performed by authorized personnel.
  • Ensure the device is completely cooled before storage.
  • Do not place the device near flammable solvents or gases.
  • Maintain at least 1 meter distance between the lamp head and users/flammable items.
  • Use only accessories approved by Godox to prevent fire or electric shock.
  • Clean gently with a dry cloth; do not use a wet cloth.

LED Modeling Lamp Caution:

Hot surface. Do not touch.

RISK GROUP 2 (LED Modeling Lamp): Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eyes.

Lithium Battery Precautions:

  • Do not disassemble, crush, or puncture the battery.
  • The battery is not waterproof; do not immerse it in fog or water.
  • Avoid short-circuiting the battery contacts.
  • Do not expose the battery to or put it into fire.
  • Do not expose the battery to temperatures above 60°C.
  • Keep out of reach of children.
  • Protect the battery from excessive shock or vibration.
  • Do not use a damaged battery.
  • If the battery leaks, avoid contact with the leaking fluid. If fluid contacts eyes, rinse with water for at least 15 minutes and seek medical attention.
  • Handle batteries according to local laws and regulations.

3. What's in the Box

The standard package includes the following items:

  • Flash Body x1
  • Storage Bag x1
  • Diffuser x1
  • Adapter x1
  • Mini Stand x1
  • Lithium Battery x1
  • USB-C Charging Cable x1
  • Instruction Manual x1
Contents of the Godox V480 box, including the flash unit, battery, charger, diffuser, mini stand, storage bag, USB-C cable, and manual.
Figure 3.1: Godox V480 Standard Kit Contents

Separately Sold Accessories

The V480 can be used with various separately sold accessories to enhance your photography experience:

  • Flash Trigger X2T Series
  • Flash Trigger XProII Series
  • Flash Trigger X3 Series

Ensure you purchase the correct accessories compatible with your specific flash model.

4. Name of Parts

Diagram of the Godox V480 flash unit with numbered parts.
Figure 4.1: Godox V480 Parts Diagram
  1. Catchlight Panel (white)
  2. Built-in Wide-angle Diffuser (transparent)
  3. Flash Head
  4. LED Modeling Lamp
  5. Battery Charging Indicator (red in charging, green when fully charged)
  6. USB Type-C Charging Port (for battery charging)
  7. Photocell Sensor
  8. Lock Ring
  9. Hot Shoe
  10. Sync Cord Jack
  11. Touch Screen
  12. USB-C Firmware Upgrade Port (for firmware upgrading)
  13. Power Switch Button
  14. Set Button
  15. Select Dial
  16. Test Button / Recycle Indicator
  17. Hot Shoe Fixing Buckle

2" Touch Screen Panel

The 2-inch color touchscreen and tactile buttons provide intuitive control. Tap, swipe, or press buttons to navigate menus and change settings quickly.

Close-up of the Godox V480's touchscreen interface, showing flash settings and controls.
Figure 4.2: Intuitive Touchscreen & Buttons

5. Setup

5.1 Installing the Diffuser

Align the bump side of the diffuser with the "V480" icon side of the flash body and insert it with moderate force until it's firmly installed.

5.2 Installing/Disassembling Battery

Installing: Insert the battery into the battery compartment in the correct direction until it locks firmly, then close the lid.

Disassembling: Slide the battery compartment lid in the indicated direction, then pull the battery out of the compartment.

5.3 Installing/Disassembling the Camera Flash

Installing: Rotate the hot shoe fixing buckle to the left, insert the camera flash into the camera's hot shoe, then rotate it to the right until it locks up.

Disassembling: Press and rotate the hot shoe fixing buckle to the left until it is loosened, then take off the camera flash.

Always power off the camera and flash when installing or disassembling to prevent damage.

5.4 Power Management

Power On: Long press the power switch button until the "SET" icon appears. Then, slide the screen or rotate the select dial to turn it on.

Note: The screen backlight automatically dims after 15 seconds of inactivity. Touch the screen to re-illuminate.

Standby: In Wi-Off/Sender mode, if standby is on, the flash enters standby after approx. 90 seconds of idle use. Press the camera shutter halfway or any button to wake it up.

Auto Off: In Wi-Off/Sender mode, if auto off is on, the flash shuts down after 60 minutes (or 30/90 minutes, depending on settings) of idle use. In Receiver mode, it also shuts down after 60 minutes (or 30/90 minutes) of idle use. Auto off can be manually turned off when using off-camera as a receiver unit.

6. Operating Modes

6.1 Battery Level Indication

Check the battery icon on the LCD panel to monitor the remaining battery level. When the battery level is low (blank grid or blinking alert), recharge or replace the battery promptly.

Battery Level IndicationMeaning
3 gridsFull
2 gridsMiddle
1 gridLow
Blank gridLower battery, please recharge it.
No battery alert blinkingBattery level is going to be used out, flash is not functional. Recharge within 10 days.

6.2 Wi-Off Mode (On-Camera Flash)

In Wi-Off mode, the flash operates as an on-camera unit. Use the touchscreen or select dial to navigate to this mode.

M: Manual Flash: Adjust flash output from 1/256 to 1/1 or 2.0 to 10 in 0.1 or 0.3 increments. Use a hand-held flash meter for precise exposure.

TTL: TTL Auto Flash: The camera's metering system automatically adjusts flash output for balanced exposure. Adjust Flash Exposure Compensation (FEC) from ±3 stops in 1/3 increments.

ZOOM: Setting the Flash Coverage: Choose between Auto Zoom (A-mm) or Manual Zoom (24-105mm for V480 C/S/N; 12-52mm for V480 O; 16-69mm for V480 F). Auto zoom adjusts coverage based on lens focal length.

6.3 Sender Mode (Master Flash)

In Sender mode, the V480 acts as a master unit to control other flashes wirelessly. Default wireless is ON.

Groups: Supports five groups: A, B, C, D, E (V480 C) or M, A, B, C, D (V480 S/N/O/F).

M: Manual Flash - Flash Power: Adjust flash power for individual groups. Press and hold the group box to switch between M, TTL, and OFF.

TTL Auto Flash - Flash Exposure Compensation Amount: Adjust FEC for individual groups. Press and hold the group box to switch between M, TTL, and OFF.

Adjust Parameters Uniformly: Increase or decrease flash power or FEC amount uniformly across groups.

ZOOM: Setting the Flash Coverage: Same as Wi-Off mode.

6.4 Receiver Mode (Slave Flash)

In Receiver mode, the V480 acts as a slave unit, controlled by a master flash. Default wireless is ON.

Groups: Supports five receiver groups: A, B, C, D, E.

TTL: TTL Auto Flash: Automatically adjusts flash output based on master unit commands.

M: Manual Flash: Manual flash power settings, controlled by the master unit.

ZOOM: Setting the Flash Coverage: Same as Wi-Off mode.

7. Advanced Functions

7.1 Sync Mode

High-speed Sync (HSS): Enables flash synchronization with all camera shutter speeds (up to 1/8000s, or 1/80000s with Sony global shutter cameras). Useful for fill-flash portraits.

Second-curtain Sync: Creates a light trail effect with slow shutter speeds. The flash fires just before the shutter closes.

7.2 Photocell (Optical Slave)

S1 Mode: The flash fires synchronously with the main flash. Useful for creating multiple lighting effects in M manual flash mode.

S2 Mode: The flash ignores a single "pre-flash" from the main flash and fires in response to the second, actual flash. Useful with cameras that have a pre-flash function in M manual flash mode.

7.3 Beep

The flash emits a prompt tone when turned on. This function can be toggled on/off via the touchscreen or select dial.

7.4 Modeling Lamp

The built-in LED modeling lamp has adjustable brightness (1-10 levels). It helps preview light effects and fine-tune your setup before firing the main flash.

A photographer adjusting the 10-level modeling lamp on the Godox V480 flash unit.
Figure 7.1: 10-Level Modeling Lamp in use

7.5 Screen Lock

Lock the touchscreen to prevent accidental changes. Press and hold for 2 seconds to unlock.

7.6 Multi Flash (Stroboscopic)

Fires a rapid series of flashes to capture multiple images of a moving subject in a single photograph. You can set the flash frequency (Hz), number of flashes, and flash output (1/256-1/4 or 2.0-8.0).

To prevent overheating, do not use multi flash more than 10 times consecutively. Allow at least 15 minutes rest after 10 consecutive uses.

7.7 Flexible Bounce Head

The flash head can tilt from -7° to 120° and swivel a full 330° for precise bounce angles. Use walls, ceilings, or floors to craft soft, natural fill light or striking side light.

Diagram illustrating the flexible bounce head of the Godox V480, showing tilt from -7 to 120 degrees and swivel from 0 to 330 degrees.
Figure 7.2: Flexible Bounce Head

Note:

  • If the bounce surface is too far, the flash might be too weak.
  • Use plain, white surfaces for optimal reflection. Non-white surfaces may cause color casts.

7.8 Creative Light Shapers (Catchlight Panel & Wide-angle Diffuser)

Slide in the catchlight panel for crisp, sparkling eyes or snap on the wide-angle diffuser to soften and broaden coverage. These built-in tools allow you to shape your light instantly without extra attachments.

Catchlight Panel: Pull out the built-in reflector and wide-angle diffuser, then push the wide-angle diffuser back. This creates a highlight in the subject's eyes, making them more charming. Optimal effect when the flash head is up 90°.

Wide-angle Diffuser: Pull out the built-in wide-angle diffuser to enlarge the flash lighting range for a softer, more natural effect. The ZOOM value is fixed at 14mm when the wide-angle diffuser is pulled out.

A photographer using the Godox V480 flash with its creative light shapers, including the catchlight panel and wide-angle diffuser, for a portrait shot.
Figure 7.3: Creative Light Shapers in action

7.9 Control with the Camera's Menu (V480 C only)

If the V480 C is attached to an EOS camera with flash control function, you can adjust flash settings directly from the camera's menu. Available settings vary based on flash mode and wireless settings.

7.10 Global Shutter Sync Shooting (V480 S only)

When using the V480 S with a global shutter image sensor camera, flash photography can synchronize across the entire range of shutter speeds, offering more effective flash exposures than traditional High-Speed Sync (HSS).

In TTL auto flash mode with a global shutter camera, the flash synchronizes properly at both low and high shutter speeds, with faster recycle times and more shots compared to non-global shutter cameras.

In M manual flash mode, for single pulse flash in high-speed shutter (faster than 1/600s), you can adjust the camera's flash delay time to match the exposure time for optimal light. This provides a better flash index than HSS mode at the same power.

8. Wireless Flash Shooting (2.4G Wireless Transmission)

The V480 can act as a sender (master) unit to control other Godox 2.4G wireless flashes (e.g., V480, AD100PRO, V100) as receiver (slave) units.

Preconditions:

  • The channel, group, and ID of both sender and receiver units must be set to the same value.
A photographer using the Godox V480 flash as a sender unit to trigger an off-camera flash with a softbox, demonstrating wireless functionality.
Figure 8.1: Sender & Receiver Functionality

8.1 Wireless Settings

Access wireless settings by sliding the screen from left to right and selecting the "Wireless" icon.

Scan Spare Channel: Scan for idle channels (01-32) to avoid interference. Select a channel from the 8 displayed spare channels.

Channel Settings: Change wireless channels (01-32) to prevent signal interference. Sender and receiver units must be on the same channel.

ID Settings: Change wireless ID (OFF/01-99) to avoid interference. Sender and receiver units must have the same ID.

Wireless Sync: This function helps quickly set the same channel and ID for sender and receiver units.

  • Receiver Wireless Sync: Set V480 to sender mode (yellow "Sender" icon). Assume a retro camera flash (e.g., Lux Master) as the receiver. Click "SYNC" on both V480 and Lux Master.
  • Sender Wireless Sync: Set V480 to receiver mode (yellow "Receiver" icon). Assume a flash trigger (e.g., X3) as the sender. Click "SYNC" on both V480 and X3.
  • If both sender and receiver units are V480, wireless sync is also available.

8.2 Wireless Multiple Flash Shooting

In TTL Auto Flash Mode: Set V480 (sender) groups (A, B, C, D, E) to <TTL>. Receiver units will automatically perform TTL auto flash. FEC set on the sender unit will be followed by receiver units.

In M Manual Flash Mode: Set V480 (sender) groups (A, B, C, D, E) to the desired manual flash output. Receiver units will follow the sender's output.

In Different Flash Modes: Set V480 (sender) groups (A, B, C, D, E) to different flash modes (e.g., TTL, M). Receiver units will perform wireless multiple flash shooting in their respective modes. FEB set on the sender unit will be followed by receiver units.

In Multi Flash Mode: Set V480 (sender) to multi flash mode. Receiver units will perform wireless multiple flash shooting following the sender's output, number of flashes, and flash frequency. Each sender unit can control up to five groups of multi flashes.

9. Maintenance

General Care: Clean the device gently with a dry cloth. Do not use a wet cloth as it may damage the device.

Battery Storage: Charge the lithium battery to about 50% before storage. Recharge it to 50% at least every six months. Store removable batteries separately. Storage temperature should be between 0°C and 40°C.

Over-Temperature Protection: To prevent overheating, avoid continuous flashes at 1/1 full power (more than 60 in HSS mode). If the over-temperature protection activates (icon appears, recycle time extends), allow the flash to cool down for about 10 minutes.

Other Protections (Error Codes): The system provides real-time protection. Refer to the troubleshooting section for error code meanings.

10. Troubleshooting

10.1 The camera flash does not fire.

  • Ensure the camera's mounting foot is securely attached.
  • Clean electrical contacts of the flash and camera with a dry cloth.
  • Wait for the flash to fully recycle (flash ready indicator lights up).
  • If the flash ready indicator lights up but the sync icon is not displayed in the camera's viewfinder, check the flash unit's secure attachment to the hot shoe.
  • If the flash ready indicator does not light up after a long wait, check battery power and replace/charge if low.

10.2 The power turns off by itself.

  • In Wi-Off/Sender mode with standby on, the flash enters sleep mode after 90 seconds of idle use. Press the camera shutter halfway or any button to wake it up.
  • In Wi-Off/Sender mode with auto off on, the flash shuts down after 60 minutes (or 30/90 minutes, depending on settings) of idle use. Restart the flash unit.
  • In Receiver mode with auto off on, the flash shuts down after 60 minutes (or 30/90 minutes) of idle use. Restart the flash unit.

10.3 Auto zoom does not work.

  • Ensure the camera flash's mounting foot is securely attached to the camera.

10.4 The flash exposure is underexposed or overexposed.

  • If using high-speed sync, the effective flash range is shorter. Ensure the subject is within the displayed effective flash range.
  • Adjust the proper FEC value.

10.5 Photos have dark corners or only parts of the target subject are illuminated.

  • The lens focal length may exceed the flash coverage. Check the flash coverage setting. The V480 has coverage between 24-105mm.
  • Set the flash coverage to auto flash zoom.

10.6 Not Triggering in Godox 2.4G Wireless.

  • 2.4G Signal Interference: Adjust the channel (CH) setting on the flash trigger (add 10+ channels) to an undisturbed channel, or turn off other 2.4G equipment.
  • Flash Recycle/Overheat: Ensure the flash has finished recycling and is not in an overheat state. Reduce flash power output. In TTL mode, try M mode (pre-flash needed in TTL).
  • Distance Too Close: If the distance between flash trigger and flash is <0.5m, turn on "close distance wireless mode" (refer to manual for specific trigger series).
  • Low Battery: Replace or charge batteries in both trigger and flash.
  • Outdated Firmware: Upgrade firmware for both flash trigger and camera (refer to respective manuals).

11. Specifications

FeatureSpecification (V480 C/S/N/F/O)
Guide Number (1/1 step, 105mm focal length)Approx. GN50 (ISO 100, in meters)
Flash Head AngleSwinging/tilting head (bounce flash): 0 to 330° horizontally and -7° to 120° vertically
Flash Duration (t0.1)1/600s-1/20000s
Exposure Control SystemTTL auto flash and manual flash
Flash Exposure Compensation (FEC)±3 steps with 1/3 increment each step
Sync ModeHigh-speed sync (up to 1/8000s, or 1/80000s with Sony global shutter), first-curtain sync, second-curtain sync
Multi FlashProvided (up to 100 times, 100Hz)
Wireless FunctionSender, Receiver
Sender GroupsA, B, C, D, E (V480 C) or M, A, B, C, D (V480 S/N/O/F)
Receiver GroupsA, B, C, D, E
Transmission Range (approx.)100m
Channels32:01~32
IDOFF/01~99
LED Modeling Lamp Power2W
Color Temperature5300K±300K
Lithium Battery7.2V/2200mAh
Recycle TimeUpto 1.7s (longer with continuous flashes)
Number of Flashes (1/1 step)Approx. 650
Power SavingStandby and auto off functions
Sync Triggering ModeHot shoe, 2.5mm sync cord
Dimensions (W x H x D)6.54" x 2.8" x 1.93" (166mm x 71mm x 49mm)
Net Weight Without BatteryApprox. 282g
Net Weight With BatteryApprox. 361g

Specifications and data are subject to change without notice.

12. Firmware Upgrade

The Godox V480 supports firmware upgrades via its USB-C port. Use a USB-C cable (sold separately) for this process.

Firmware upgrades require the Godox G3 V1.1 software. Download and install the "Godox G3 V1.1 firmware upgrade software" before upgrading. Then, select the appropriate firmware file.

For the latest electronic version of the instruction manual and firmware files, please visit the official Godox website:

https://www.godox.com.cn/firmware-G3/

13. Compatible Camera Models

The Godox V480 comes in different versions, each compatible with specific camera brands:

  • V480 C (Canon): 80D, 90D, 7D, 6D, 70D, 750D, 760D, 5D Mark IV, EOS 1DX, 6D Mark II, 77D, 800D, 5D Mark III, 5D Mark II, 60D, 7D Mark II, 600D, 50D, 30D, 40D, 500D, M5, M3, M50, R, RP, M6II, R5, 1500D, 3000D, R7, R6II, R50, R8, R5C, R10, R100, R5II, R3, 200DII.
  • V480 S (Sony): α77II, α99, α77, DSC-RX10, α6000, α7R, α350, α7RII(4.0), α7RIII, α7M3, α9, α7RIV, α7R5, α7MIV, ZV-E10, A9III, A7C, A7CII, α6400, α6500.
  • V480 N (Nikon): D800, D750, D700, D610, D500, D200, D300S, D5, D4, D810, D780, D5300, D5200, D5100, D5000, D3300, D3100, D60, Z6, Z7II, Z8, ZFC.
  • V480 O (Olympus/Panasonic):
    • Olympus: E-M1, PEN-F, E-M10II, E-PL8, E-P5, E-M10III.
    • Panasonic: GH4, LX100, DMC-GF1, DMC-G85, DMC-GX85, DMC-LX100, DMC-FZ2500GK, S1.
  • V480 F (Fujifilm):
    • A Series: X-Pro2, X-T20, X-T2, X-T1, GFX50s, GFX50R, X-T30, X-T4, X-T3, X-S20, X-T5.
    • B Series: X-Pro1, X-T10, X-E1, X-A3.
    • C Series: X100F, X100T.

These tables list tested models. For other models, self-testing is recommended. Godox reserves the right to modify this compatibility list.

14. User Tips

  • Battery Life: To maximize battery life, store the lithium battery at around 50% charge and recharge every six months.
  • Soft Light: For softer, more diffused light, always use the wide-angle diffuser or bounce the flash off a large, neutral-colored surface.
  • Creative Effects: Experiment with the flexible bounce head and modeling lamp to pre-visualize and achieve desired lighting effects.
  • Wireless Reliability: When using wireless flash, ensure your sender and receiver units are on the same channel and ID to avoid misfires. If experiencing issues, scan for a clear channel.
  • Firmware Updates: Regularly check the Godox website for firmware updates to ensure compatibility with new camera models and optimal performance.

15. Warranty and Support

The warranty period for this device is one year from the purchase date. Consumables such as batteries, adapters, power cords, and other accessories are not covered by the warranty.

Unauthorized repairs will void the warranty. For any quality issues upon receipt, please contact Godox or an authorized dealer.

For maintenance service, please contact your product distributor or authorized service institutions. You can also reach Godox after-sale service:

Godox After-sale Service Call: +86-755-29609320 (8062)

Email: godox@godox.com

Address: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao'an District, Shenzhen 518103, China

© 2024 Godox. All rights reserved.

Made in China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.