KEBETEME EM415Pro

Contents

Automotive Tester Cable Wire Short & Open Finder Instruction Manual

Model: EM415Pro | Brand: KEBETEME

1. Introduction

The KEBETEME EM415Pro Automotive Tester is designed to efficiently detect and alert you to open circuits, short circuits, broken wires, and current leaks in vehicle electrical systems. This professional tool allows for quick and easy tracing of wires and pinpointing problem locations, even intermittent circuit issues, by listening for changes in the receiver tone. It features a direction indicator to guide you to the short circuit, eliminating guesswork. The device operates on DC voltages ranging from 6 to 42 volts, making it suitable for a wide range of vehicles including automobiles, trucks, tractors, boats, and RVs.

Video: Overview of the Automotive Short and Open Finder in use.

2. Safety & Warnings

Important Safety Information:

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.

3. Package Contents

Your package should contain the following item:

  • 1 x Automotive Short and Open Finder (Transmitter and Receiver unit)

4. Product Features

  • Quickly and easily locate short circuits, open connections, broken wires, and current leaks.
  • Trace cables or wires and diagnose break points without damaging insulation.
  • Receive tone signals on cables or wires (including telephone lines).
  • Identify the state of a working telephone line (clear, ring, busy).
  • Send a single solid tone or a dual alternating tone to target cables or wires.
  • Tracing possible even inside bundles, conduits, behind panels, under carpets, upholstery, etc.
  • Easy to use: connect the transmitter in series with the circuit or wire under test (e.g., in place of a blown fuse, across a connector, in series with an open wire, a light bulb socket).
  • Scan the circuit/wire with the receiver's flexible probe to find the trouble spot.
  • 42V Ready: Compatible with new generation vehicles featuring mixed or single 42 Volt systems.
  • Operates on DC voltages from 6 to 42 volts.
  • Internally protected against power surges and overloads.
  • 7-inch flexible probe allows reaching wires in congested places.
  • Transmitter and Receiver LEDs indicate open or short circuit conditions.
  • Adjustable sensitivity for all tracing situations.
  • Non-contact technology, no wire piercing required.
Automotive Tester Cable functions and components

Image: Key functions including cable tracking, short circuit finding, break point checking, and cable identification.

5. Specifications

Feature Detail
Power Source Two 9V batteries (Not Included)
Operating Voltage 6 to 42 Volts DC
Material Type Coiled steel (probe)
Receiver Dimensions (approx.) 240mm (Length) x 44mm (Width)
Transmitter Dimensions (approx.) 68mm (Height) x 58mm (Width)
Probe Length 7 inches (flexible)
High-concerned chemical None
Electronic No
Wireless Support No
Batteries Included No
Origin Mainland China
Dimensions of the Automotive Short and Open Finder

Image: Dimensions of the EM415Pro Automotive Short and Open Finder.

6. Setup

6.1 Installing Batteries

The device requires two 9V batteries (not included). Locate the battery compartment on both the Transmitter and Receiver units, open it, insert the batteries with correct polarity, and close the compartment securely.

6.2 Connecting the Transmitter

To prepare for testing, connect the transmitter to the vehicle's electrical system:

  1. Connect the red test lead clip of the transmitter to the positive (+) terminal of the vehicle's battery.
  2. Connect the black test lead clip of the transmitter to the negative (-) terminal (ground) of the vehicle's battery.
  3. Connect the transmitter's test leads to the specific circuit or wire you intend to test. This can be done in series with the circuit, in place of a blown fuse, across a connector, or in series with an open wire or light bulb socket.
Automotive Tester Cable connected to a car battery

Image: Transmitter connected to a vehicle's battery for testing.

7. Operating Instructions

7.1 Component Overview

Labeled diagram of the Automotive Short and Open Finder components

Image: Labeled diagram showing the Receiver (Probe, Sensor, Rotary switch, Test button, Battery Compartment, Buzzer) and Sender (Test lead, Switch).

7.2 General Operation

  1. Ensure the transmitter is correctly connected to the circuit under test as described in the Setup section.
  2. Turn on the receiver unit.
  3. Adjust the sensitivity knob on the receiver to an appropriate level.
  4. Use the receiver's flexible probe to scan along the wire or circuit path.
  5. Listen for the audible tone from the receiver. A change in tone or its cessation indicates a problem area.

7.3 Checking Cable Break Point

Follow these steps to locate a break point in a cable:

  1. Turn the switch on the transmitter to the "TONE" position.
  2. Connect the transmitter's black clip to a ground wire. Fuse sockets and connectors can also serve as ideal access points. Connect the red clip to the cable you want to track.
  3. Turn on the receiver and rotate its sensitivity knob clockwise to the middle position.
  4. Press and hold the "TEST" button on the receiver.
  5. Slowly sweep the receiver's probe along the cable, pipeline, or other components.
  6. If there is a consistent sound, the cable is normal. If the sound becomes faint or stops, it indicates that the probe has passed over a damaged section, an open point, a disconnection, or a damaged connection point in the circuit.
  7. The exact location where the audio signal stops is the cable break point.
Instructions for checking cable break point and bendable probe

Image: Detailed instructions for checking cable break points and information on the bendable receiving probe.

7.4 Proper Use of the Probe

The receiver's probe is made of coiled steel and can be bent to access wires in confined or difficult areas. For optimal signal reception, position the receiver's probe tip (the black cap) perpendicular (at a 90-degree angle) to the wire being traced, either directly above or below it.

Diagram showing correct and incorrect probe positioning

Image: Diagram illustrating the proper (perpendicular) and improper (parallel) orientation of the probe for effective tracing.

8. Maintenance

  • Keep the device clean and dry. Wipe with a soft, damp cloth if necessary. Do not use abrasive cleaners or solvents.
  • Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
  • Remove batteries if the device will not be used for an extended period to prevent leakage.
  • Regularly inspect the test leads and clips for any signs of wear or damage. Replace if necessary.

9. Troubleshooting

9.1 No Signal or Weak Signal

  • Check Battery Levels: Ensure both the transmitter and receiver have fresh 9V batteries installed.
  • Verify Connections: Make sure the transmitter's clips are securely connected to the power source and the circuit under test.
  • Adjust Sensitivity: Increase the sensitivity on the receiver unit.
  • Probe Orientation: Ensure the receiver's probe is positioned correctly (perpendicular to the wire) for optimal signal pickup.
  • Circuit Integrity: Confirm the circuit you are testing is powered and has continuity up to the point of testing.

9.2 Inaccurate Readings

  • Interference: Electrical interference from other components or wiring can affect readings. Try to isolate the area being tested.
  • Probe Distance: Ensure the probe is close enough to the wire being traced.
  • Sensitivity Adjustment: Fine-tune the sensitivity to avoid picking up signals from adjacent wires.

10. User Tips

No specific user tips were available from provided reviews or Q&A. However, general tips for using automotive circuit testers include:

  • Always start with the lowest sensitivity setting and gradually increase it as needed to avoid false positives from nearby wires.
  • When tracing wires in complex harnesses, try to isolate the wire as much as possible to get a clearer signal.
  • For intermittent problems, gently flex and wiggle wires and connectors while listening for changes in the receiver's tone to help pinpoint loose connections or internal breaks.

11. Warranty & Support

11.1 Manufacturer Information

Name: Shenzhen Meiteai E-commerce Co., Ltd

Address: CN-Building A, Building 201A, No. 8-14 Jinyuan Road, He'ao Community, Yuanshan Street, Longgang District, Shenzhen, 518000, China

Email: qiujianqiang@youyuepin.cn

Telephone: 86-13714205204

11.2 EU Authorized Representative

Name: SUCCESS COURIER SL

Address: CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947, Spain

Email: successservice2@hotmail.com

Telephone: 34-+34910602659

12. Compliance Information

This product bears the CE marking, indicating its conformity with health, safety, and environmental protection standards for products sold within the European Economic Area (EEA).

CE

NOTE: This product must comply with all applicable safety and regulatory requirements in the market where it is sold. Sellers must assess which requirements and regulations apply based on the actual product type, function, and destination market.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.