ZASTONE MD9000

Contents

ZASTONE MD9000 DMR Digital Car Walkie Talkie User Manual

Model: MD9000 | Brand: ZASTONE

1. Introduction

Thank you for purchasing the ZASTONE MD9000 DMR Digital Car Walkie Talkie. This rugged, high-quality, long-range, high-performance multi-band vehicle-mounted transceiver is meticulously designed for car enthusiasts. It supports UHF/VHF wide-band analog + digital dual-mode systems, offering compatibility with existing conventional analog systems and direct mode dual-slot communication.

Key features include various calling methods, voice encryption (ARC4 and AES256), manual frequency input, one-touch calling, one-touch emergency alert, short messaging, GPS/BeiDou/GLONASS positioning, and Digital APRS functionality.

This manual provides detailed instructions for the proper installation, operation, and maintenance of your MD9000 transceiver. Please read it thoroughly before use to ensure optimal performance and safety.

ZASTONE MD9000 DMR Digital Car Walkie Talkie with microphone, showing Digital APRS Automatic Grouping Reporting System features.

Figure 1: ZASTONE MD9000 DMR Digital Car Walkie Talkie highlighting APRS features.

2. Safety Precautions

WARNING:

  • Do not use this device while driving, as it is dangerous.
  • This transceiver is designed to operate on a 12-13.8V DC power supply.
  • Do not place the device in dusty, humid, or splashed water environments, or on unstable surfaces.
  • If the device experiences external interference, move it away from interference sources (such as televisions, generators, etc.).
  • Do not expose the device to direct sunlight for extended periods or place it near heating devices.
  • If the device emits smoke or strange odors, immediately cut off the power, ensure the device is safe, and send it to the nearest service station for inspection.
  • Avoid prolonged high-power transmission, which may cause the transceiver to overheat.
  • Before using the device, ensure the antenna is installed properly before turning it on (operating radio equipment without an antenna can cause damage).

NOTICE:

According to Radio Regulation of the People's Republic of China, organizations and individuals setting up and using radio equipment within the territory of the People's Republic of China must apply for a station license from the relevant radio management agency and obtain a radio station license before use.

Your multi-band vehicle-mounted transceiver complies with Chinese standards, the US FCC, and European CE standards.

When programming the transceiver, first read the original factory data, then modify the frequency, signaling, etc., and write it back. Otherwise, errors may occur due to different models and frequency bands.

3. Supplied and Optional Accessories

Please check the packaging contents against the list below. It is recommended to keep the original box and packing materials for future use.

3.1. Supplied Accessories

  • Controller
  • Microphone [HM-66] (with DTMF keypad)
  • Power Supply [XT30-1F]
  • DC Power Cable and Fuse Holder [XT30-2F]
  • Metal Hardware Kit for Bracket (Black screws, Tapered screws, S-type washers)
  • Microphone Hook [TG-1]
  • USB Programming Cable [HPC-01]
  • Spare Fuses (one pair) [HF-01]
  • Mobile Mounting Bracket [HMB-02]

3.2. Optional Accessories

  • Wireless Microphone BE-1
  • External Speaker (SP-02)
  • Mobile Antenna [HCA-01]
ZASTONE MD9000 car intercom with included accessories: Type-C data cable, power line, GPS antenna, host bracket, hand mic, insurance, hand microphone hook.

Figure 2: Included accessories for the ZASTONE MD9000.

4. Setup

4.1. Mobile Installation

When installing the transceiver in a vehicle, choose a safe and convenient location that minimizes risk to passengers and does not interfere with driving. Ensure good ventilation and avoid direct sunlight.

  • Do not obstruct normal vehicle operation or airbags.
  • Avoid placing near air conditioning vents.
Diagram showing recommended installation location for the transceiver in a car dashboard.

Figure 3: Recommended installation location in a vehicle.

4.2. Microphone Connection

Connect the microphone to the transceiver's main unit or panel as shown in the diagram.

Diagram showing the connection of the microphone to the transceiver main unit.

Figure 4: Microphone connection diagram.

4.3. DC Power Cable Connection

The transceiver connects to a 12-13.8V battery. Ensure sufficient current capacity. Route the DC power cable directly from the transceiver to the battery terminals, keeping the cable as short as possible. Wrap heat-resistant tape around the fuse box and secure the cable.

  • Connect the red wire to the positive (+) terminal and the black wire to the negative (-) terminal.
  • Use the entire cable without cutting off any excess.
  • Secure connectors until the latch clicks into place.
  • Recommended power supply current capacity is 12A.
Diagram showing DC power cable connection to a car battery and external power plug.

Figure 5: DC Power Cable Connection.

4.4. Antenna Connection

Install a high-efficiency and precisely tuned 50Ω antenna with a low-loss coaxial feeder line. Transmitting without an antenna or matched load may damage the transceiver. All fixed stations should be equipped with a lightning arrester.

Recommended Specifications for Antenna:

  • Length: Approximately 1 meter.
  • Gain: Around 5.5 dB.
  • SWR (Standing Wave Ratio): Ideally below 1.5.
Diagram illustrating recommended antenna positions and mounting methods for a vehicle.

Figure 6: Recommended antenna installation positions.

The antenna uses an L16 connector and a Q9 connector. Detailed instructions on antenna installation are available in the full user manual PDF. If the feeder line is too long, arrange the excess cable in a serpentine (Z-shaped) pattern.

4.5. External Mono Speaker

If using an external speaker, choose an 8Ω dual-channel external speaker. The external speaker jack accommodates a 3.5mm mono plug.

4.6. PC Connection

To use programming software, connect the transceiver to the PC using the optional programming cable (HPC-01) via the TYPE-C port. Contact your dealer for information on purchasing the programming cable.

5. Operating Instructions

5.1. Power On and Off

  • Power On: Briefly press the [PWR] button. The transceiver will emit a double beep, and the LCD screen will display the startup message before showing indicators and the current operating frequency.
  • Power Off: Briefly press the [PWR] button. Current settings are saved and restored upon next power-on.

5.2. Volume Adjustment

Adjust the volume using the [VOL] knob. Turn clockwise to increase, counterclockwise to decrease. You can press and hold the monitor button to listen to background noise for more accurate adjustment.

5.3. Getting Acquainted with Controls

Front Panel

Front panel diagram with numbered buttons and their functions.

Figure 7: Front Panel Layout and Controls.

Front Panel Functions
No. Key Function
1Left Main Mode Button [MAIN*BAND]Sets left band as main band mode.
2Left Volume Knob [VOL]Increases radio volume (clockwise).
3Right Main Mode Button [MAIN*BAND]Sets right band as main band mode.
4Right Volume Knob [VOL]Increases/decreases radio volume.
5Left Band Selector Knob [DIAL]Selects left band's frequency or channel.
6Left [VFO*MW] ButtonSwitches between frequency/channel mode on left side.
7Right Band Selector Knob [DIAL]Selects right band's frequency or channel.
8Right [VFO*MW] ButtonSwitches between frequency/channel mode on right side.
9PWRLong press to turn on/off radio.
10LOW VFO/MRShort press to switch power levels. Long press to toggle VFO/channel mode.
11DUAL MONIShort press to switch single/dual band modes. Long press to activate monitor mode.
12MENUEnters menu interface.
13P1User-Defined Button (programmable).
14P2User-Defined Button (programmable).
15P3User-Defined Button (programmable).
16EXITReturns to main screen from menu.

Rear Panel

Rear panel diagram with numbered ports (RF antenna output, fan, 12-13.8V power, GPS antenna, speaker, external audio, ACC interface) and appearance parameters (model, size, weight, color).

Figure 8: Rear Panel Layout and Ports.

Rear Panel Ports
No. Port Function
1Antenna ConnectorConnects antenna (50 ohms impedance).
2External ACC PlugConnects to cigarette lighter for auto power on/off with vehicle engine.
3Cooling FanAutomatically activates when radio temperature rises.
4External Dual-Channel Speaker PortConnects an optional external speaker.
5Power Input12-13.8V power input port.

Microphone

Microphone diagram with numbered buttons and their functions, including a MIC connector diagram.

Figure 9: Microphone Layout and Functions.

Microphone Key Functions
No. Key Function
1IncreaseIncreases frequency values, memory channel numbers, or settings.
2DecreaseDecreases frequency values, memory channel numbers, or settings.
3Emergency Alarm ButtonLong press to activate emergency alarm; short press to cancel.
4Receive/Transmit Indicator LightGreen LED for receiving, Red LED for transmitting.
5Main/Sub Channel SwitchSwitches between left or right transceiver as main channel.
6Numeric KeypadUsed for function settings, VFO frequency input, or DTMF dialing.
7PTT ButtonPress to enter transmit state.
8MicrophoneSpeak here during transmission.

5.4. Display Indicators

LCD large screen display with Chinese and English options, showing menu interface and backlight color options (blue, red, green).

Figure 10: LCD Display and Backlight Options.

Display Indicators Overview
No. Indicator Function
1MAINMain Channel Indicator
2Mute
3Message Received
4VOXVoice-Activated Transmission
5RECRecording Function
601:54Time
7GPS On (Located)/GPS On (Not Located)
8Monitor
9Auto Power-Off
10Keypad Lock
11DIGDigital Channel
12DCOMDirect Mode Dual Time slot
13ANAAnalog Channel
14T1Time slot 1
15Scan Active/Paused (Signal Found)/Priority Channel Found
16H M LHigh/Medium/Low Power
17Encryption On
18NNarrow Band (Digital Mode Time slot)
19CTC DCSAnalog CTCSS/Digital CTCSS
20Repeater Channel (Negative/Positive Offset)/Off-Network
21140.125Current Channel Frequency
22Digital ZoneVFO/Zone/Channel Name
23VFOEditable Frequency in VFO Mode
24BUSYSignal Strength Indicator
25MRChannel Mode
26001Channel 1
27Bluetooth On (Connected)/Bluetooth Off (Not Active)

5.5. Setting Frequency

The transceiver operates in two modes: Frequency Mode (VFO) and Channel Mode (MR). Press and hold the preset LOW/VFO/MR key to toggle between modes.

  • Adjusting Frequency in VFO Mode: Use the [DIAL] control knob. Clockwise increases, counterclockwise decreases.
  • Inputting Frequency via Microphone Keypad: In VFO mode on the main band, use the microphone keypad. Input six digits for the frequency.

5.6. Transmitting and Receiving

  • Transmitting: Press and hold the [PTT] button. Speak 2.5-5 cm away from the microphone. Release PTT to listen.
  • Receiving: The radio monitors both left and right units. When a signal is received, the "BUSY" icon and signal strength indicator appear.
  • Canceling Squelch: In analog mode, press and hold the [DUAL MONI] key for 2-3 seconds to monitor weak signals.

5.7. Calls

The MD9000 supports various call types and features:

  • Digital Call: Private Call (one-to-one), Group Call (one-to-group), All Call (one-to-all).
  • Initiating a Call: Use the PTT button with a pre-programmed contact, or dial manually via the menu.
  • Receiving and Replying: Radio rings if caller's DMR ID is programmed. Display shows caller info. Press PTT to reply.
  • DMR Emergency Alarm: Programmable alarms (Siren Only, Secret, Secret with Voice, Normal) for critical situations.
  • Working Alone: Triggers an alarm if the radio is inactive for a pre-programmed time.
  • Encryption: Supports ARC4 and AES256 encryption for secure voice and data.

5.8. Scan Settings

The scan function monitors multiple channels. You can create up to 32 scan lists, each with a maximum of 16 channels.

  • Scan Switch: Start scanning via the pre-programmed [Scan] key or through the main menu.
  • Scan Resume Methods: Time (TO), Carrier (CO), or Search (SE).
  • VFO Scan Range: Set start and end frequencies for scanning in VFO mode.

5.9. Digital APRS Functionality

The digital APRS function provides automatic grouping and reporting. It supports Beidou+GPS dual star positioning, real-time information transmission, and identity identification.

Digital APRS function explanation with satellite positioning and real-time information transmission.

Figure 11: Digital APRS Function Overview.

  • APRS Switch: Enable to display GPS information of transmitting party.
  • Reporting ID/Type/Channel/Interval: Configure these settings via the menu.
  • Delete All APRS Data: Option to clear all stored APRS data.

5.10. Bluetooth Settings

The MD9000 supports Bluetooth connectivity for wireless microphones and PTT functions.

  • Bluetooth Pairing: The wireless microphone automatically searches for previously paired transceivers.
  • Bluetooth PTT: Supports Bluetooth headsets and PTT.
  • Bluetooth Volume/MIC Gain: Adjust audio input/output levels for Bluetooth devices.

6. Maintenance

6.1. Fuse Replacement

If a fuse blows, first determine and correct the cause, then replace the fuse. If a newly installed fuse blows, disconnect the power cable and contact an authorized dealer. Only use the specified type and rating of fuse (Transceiver: 15A, DC Power Cable: 20A).

Note: Using the transceiver when the vehicle battery is not fully charged or when the engine is off may drain the battery to the point where there is not enough power left to start the vehicle. Avoid using the transceiver in these situations.

6.2. Cleaning

Clean the keys, controls, and case with a neutral detergent and warm water. Use a damp cloth to clean the case. Do not use strong chemicals.

7. Troubleshooting

This section addresses common operational malfunctions. These issues are often caused by improper hook-up, incorrect settings, or operator error, rather than circuit failure.

Common Problems and Solutions
Problem Cause Analysis Potential Solution
Power is on, nothing appears on Display.Power connection polarities reversed.Connect red lead to plus, black to minus.
Fuse is blown.Replace fuse with new fuse after solving the problem.
Display is too dim.Display brightness regulator set too low.Set brightness to high level.
No sound comes from speaker.Squelch is muted or Tone/CTCSS/DCS squelch is active.Decrease squelch level or turn off Tone/CTCSS/DCS squelch.
Key and Dial do not function.Key-lock function is activated.Cancel Key-lock function.
Rotating Dial will not change memory channel.Transceiver is in CALL mode.Exit CALL mode.
PTT key is pressed but transmission does not occur.Microphone connection is poor.Connect microphone properly.
Cannot communicate with other members in the group.Frequency or signaling settings are different.Configure same frequency and signaling.
Incorrect digital or analog channel settings.Set same digital or analog channel.
Distance between devices is too far.Stay closer to other group members.
GPS Unable to LocatePoor location, unable to receive GPS signals.Move to an open, flat area and retry.
Digital Channel Cannot Perform Individual or Group CallsIncorrect frequency, channel, color code, or time slot settings.Configure same settings as group members.
Other (Non-group) Voices Heard on the ChannelInterference from users on same frequency. No signaling configured.Switch to new frequency or adjust squelch level. Configure signaling for all radios.
Communication distance is too far.Move closer to other group members.
Excessive Noise During CommunicationPoor location (blockage by tall buildings, basement).Move to an open, flat area and restart device.
Interference from external environment or electromagnetic sources.Avoid equipment that may cause interference.

8. Specifications

General Specifications
Feature Specification
Radio Response Bandwidth136-174MHZ 400-480MHZ
Out Power50W
Item Weight0.4kg (Unit+Microphone: 1373g)
Item Size (L*W*H)150*75*58 mm
OSD LanguageEnglish
Voltage12 V (Nominal 13.8V DC)
PlacementIn-Dash
Display Size6.2 inches (240x64 full dot matrix LCD)
MaterialMetal (Zinc alloy body)
Special FeaturesRadio Tuner
Product NameDMR Digital Car Walkie Talkie
FrequencyVHF UHF digital walkie talkie
Transmission power50W DMR Car Two Way Radio
FunctionAPRS Radio
Modulation TypeDMR Mobile Radio
EncryptionAES256 DMR Car Mobile Radio
OptionalWireless microphone
SignalingMDC1200 Radio
PositioningGPS Beidou GLONASS

8.1. Transmitter

  • RF Power Output: UHF:50W/25W/5W; VHF:50W/25W/5W
  • FM Modulation: 11K0F3E@12.5KHz, 16K0F3E @25KHz
  • Digital Modulation: 12.5KHz Only Digital: 7K60FXD12.5KHz
  • Digital & Voice: 7K60FXW
  • Modulation Distortion: <5%
  • FM Noise: ≥45dB@25KHz / ≥40dB@12.5KHz
  • Adjacent Channel Power: ≤-60dB @ 12.5KHz
  • Digital Protocol: ETSI-TS102361-1-2, -3
  • Spurious Emission: At least 60 dB below
  • Microphone Impedance: 2KΩ

8.2. Receiver

  • Sensitivity Radio Band: 2uV TYP for 12dB SINAD (64-108MHz, WFM)
  • L&R Band: 0.8uV TYP for 10dB SN(113-134MHz,AM), 0.2uV for 12dB SINAD (136-174MHz,FM), 0.2uV for 12dB SINAD (400-470MHz,FM)
  • Squelch Sensitivity: 0.16uV(144/430MHz Band)
  • Selectivity: NFMAM 12KHz/30KHz(-6dB/-60dB)
  • AF Output: 6W@4Ω for 10%THD(@13.8V)EXP SP, 3W@8Ω for 10%THD(@13.8V)Normal EXP
  • SP/CH AF Output Impedance: 4-16Ω
  • Digital Receive Sensitivity: 0.25 µV (BER: 5%)

Note: All stated specifications are subject to change without notice or obligation.

9. Warranty and Support

9.1. Service

This product has been factory aligned and tested to specification before shipment. Any service or alignment without factory authorization may void the transceiver warranty.

If equipment repair is necessary, pack it in its original box and packing material. Include a full description of the problems, your contact information (telephone, fax, e-mail), and the model and serial number of the transceiver. Do not return accessory items unless directly related to the service problem.

You may return this product for service to the authorized dealer from whom you purchased it, or any authorized service center.

CAUTION:

Do not pack the equipment in crushed newspapers for shipment! Extensive damage may result during rough handling or shipping.

Note: Record the date of purchase, serial number, and dealer information. Retain a written record of any maintenance performed. For warranty claims, include a photocopy of the bill of sale or other proof of purchase.

10. User Tips

  • Narrow Band Operation: The MD9000 supports narrow band operation (12.5K) in analog channels. This can be configured in the 'Bandwidth Settings' menu under 'Analog Device Programming'.
  • Optimal Performance: For best results, ensure your antenna is properly tuned and installed, and that the power supply is stable and sufficient.
  • Programming: While many settings can be adjusted directly on the device, using the PC programming software allows for more comprehensive configuration, especially for channel lists and contacts.

11. Additional Resources

For a complete and detailed user manual, please refer to the official PDF document available at: ZASTONE MD9000 User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.