eletechsup 4831

Contents

eletechsup 3A Synchronous Buck-Boost Voltage Regulator User Manual

Model: 4831

High-Efficiency 3A Synchronous Buck-Boost Voltage Regulator for Solar Lead-acid Batteries DC 3-23V to 3.3V 4.2V 5V 6V 10V 12V

1. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.
  • This is a DC-DC voltage converter module. When using, please note:
    1. Input voltage cannot be greater than the maximum input range.
    2. Output power cannot be greater than the maximum load for a long time.
    3. Input power must be greater than the output power, due to the module's own power consumption.

2. Product Overview

The eletechsup 3A Synchronous Buck-Boost Voltage Regulator is a high-efficiency DC-DC converter module designed to provide stable output voltages from a wide input range. It features a 4-switch buck-boost topology for optimal performance.

Video demonstrating the physical appearance and size of the eletechsup buck-boost converter module.
Top view of the eletechsup NDU B22TA buck-boost converter module
Top view of the eletechsup NDU B22TA buck-boost converter module, showing VIN, VOUT, and GND pads.
Bottom view of the eletechsup NDU B22TA buck-boost converter module with output voltage selection pads
Bottom view of the eletechsup NDU B22TA buck-boost converter module, indicating selectable output voltages (3.3V, 4.2V, 5V, 6V, 10V, 12V) via solder pads.

3. Setup and Connections

Before first use, remove any protective films from the device.

3.1. Wiring Diagram

Connect your input power source to the VIN and GND pads, and your load to the VOUT and GND pads as shown in the diagram below. Ensure correct polarity.

Wiring diagram for the 4-Switch Buck-Boost Converter
Diagram illustrating the input (DC 3-23V) and output (selectable 3.3V, 4.2V, 5V, 6V, 10V, 12V) connections for the 4-Switch Buck-Boost Converter.

3.2. Output Voltage Selection

The module supports multiple fixed output voltages. To select the desired output voltage, solder the corresponding pads on the bottom of the module. Refer to the image showing the selectable output points.

  • Available Output Voltages: 3.3V, 4.2V, 5V, 6V, 10V, 12V.
  • Ensure soldering is clean and creates a solid connection for the chosen voltage.

4. Operating Instructions

Once the module is correctly wired and the output voltage is selected, apply power within the specified input voltage range (DC 3-23V). The module will automatically regulate the output to the chosen voltage.

4.1. Performance Characteristics

The module's performance varies with different input and output voltage combinations. Always ensure your application's current draw does not exceed the maximum output current for the selected voltage.

Performance tables for various input and output voltages
Detailed performance tables showing input voltage, input current, output voltage, output current, and conversion method (Boost/Buck) for various output voltage settings.

5. Maintenance

  • After use, turn off the device and store it in a dry place.
  • Keep the module clean and free from dust and debris.
  • Avoid exposing the module to extreme temperatures or humidity.

6. Troubleshooting

  • No Output: Check input voltage, wiring connections, and ensure the output voltage selection pads are correctly soldered. Verify input power is sufficient.
  • Module Overheating: This could indicate excessive load or insufficient input power. Reduce the load or ensure the input power source can supply enough current. The module has Over-Temperature Warning and Shutdown protection.
  • Intermittent Operation: Check for loose connections or cold solder joints. Ensure the input voltage is stable and within the specified range.
  • Protection Features Triggered: The module includes Under-voltage protection (UVP), Internal Soft Start (SS), Over-Current Protection (OCP), and Output Short-Circuit Protection (SCP). If the module stops working, check for conditions that might trigger these protections (e.g., short circuit at output, excessive current draw, or too low input voltage).

7. Specifications

Feature Specification
Product Name Max 3A Synchronous 4-Switch High Efficiency DC-DC Buck-Boost Converter Module
Model 4831
Input Voltage DC 3-23V
Output Voltage 3.3V / 4.2V / 5V / 6V / 10V / 12V (Selectable)
Max Output Current 3A
Max Input Current 4A
Conversion Mode 4-Switch Buck-Boost
Switching Frequency 500KHz
Conversion Efficiency 88-93%
Quiescent Current >1mA
Operating Temperature –40°C to +105°C
Dimensions (L x W x H) 25mm x 18mm x 6.5mm
Weight Approx. 3g
Protection Features Under-voltage protection (UVP), Internal Soft Start (SS), Over-Current Protection (OCP), Output Short-Circuit Protection (SCP), Over-Temperature Warning and Shutdown

8. User Tips

  • For optimal efficiency, try to keep the input voltage reasonably close to the desired output voltage, especially when operating at higher currents.
  • Consider adding heat sinks if operating continuously at maximum load or in high ambient temperatures, although the module has over-temperature protection.
  • Always double-check your soldering for the output voltage selection to prevent incorrect voltage output.

9. Frequently Asked Questions (FAQ)

Q: Can I use this module to charge a 3.7V Li-ion battery?
A: Yes, you can select the 4.2V output option, which is suitable for charging single-cell Li-ion batteries.
Q: What happens if the input voltage drops below the selected output voltage?
A: The module is a buck-boost converter, meaning it can both step up (boost) and step down (buck) the voltage. It will attempt to maintain the selected output voltage as long as the input is within the 3-23V range and the current limits are not exceeded.
Q: Is this module suitable for continuous operation?
A: Yes, it is designed for continuous operation within its specified limits. Ensure proper ventilation, especially when drawing higher currents.

10. Manufacturer and Support

Manufacturer Information:

Guangzhou Keshen Electronic Technology Co., Ltd
Room 301, No. 8-1 Beixin Street, Kemulang Aotou, Tianhe District, Guangzhou City, China
Phone: 86-18102739603
Email: eletechsup@163.com

EU Authorized Representative:

TOCYA TRADING
79 rue de patay, 75013, Paris, France
Phone: 33-143443019
Email: TOCYATRADING75013@outlook.com

For further assistance or inquiries, please contact the manufacturer or your local distributor.

A PDF version of the user manual is available for download: User Manual (PDF)

© 2024 eletechsup. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.