KASK Protone KP Series

Contents

KASK Protone KP Series Cycling Helmet User Manual

Model: Protone KP Series

Brand: KASK

Introduction

This manual provides essential information for the proper use, setup, and maintenance of your KASK Protone KP Series cycling helmet. Designed for both road and mountain cycling, this helmet offers integrated safety features and a comfortable fit. Please read this manual thoroughly before using your helmet to ensure maximum safety and performance.

Safety Warnings

  • This helmet is designed to absorb the energy of a single impact. After any significant impact, even if no visible damage is present, the helmet should be replaced.
  • Do not modify or remove any original components of the helmet.
  • Avoid exposing the helmet to extreme temperatures or corrosive substances.
  • Ensure the helmet fits snugly and the straps are securely fastened before each ride.
  • This helmet is intended for cycling use only and does not provide protection for motor sports or other activities.

Setup and Adjustment

1. Head Circumference Measurement

To ensure a proper fit, measure your head circumference before adjusting the helmet. Use a flexible measuring tape and wrap it around your head, just above your eyebrows and ears.

Diagram illustrating head circumference measurement
Figure 1: Head circumference measurement guide. Measure around the widest part of your head, just above the ears and eyebrows.

The KASK Protone KP Series helmet is designed for head circumferences between 52-62cm, typically available in M (52-58cm) and L (58-62cm) sizes.

2. Adjusting the Fit

  1. **Placement:** Position the helmet squarely on your head, ensuring it covers your forehead. It should not be tilted back or forward.
  2. **Retention System:** Use the rear retention system (often a dial or slider) to tighten the helmet until it feels snug but comfortable. The helmet should not move excessively when you shake your head.
  3. **Strap Adjustment:** Adjust the side straps so that they form a 'V' shape just below your ears. The straps should be flat against your face and not twisted.
  4. **Chin Strap:** Fasten the chin strap buckle and tighten it so that it is snug under your chin. You should be able to fit one or two fingers between the strap and your chin, but no more.
  5. **Final Check:** Open your mouth wide. The helmet should press down on the top of your head. If it doesn't, tighten the chin strap further.

Operating Instructions

Once your helmet is properly fitted, it is ready for use. Always wear your helmet when cycling, regardless of the distance or terrain. Ensure the helmet is securely fastened before starting your ride.

Cyclist wearing a white KASK Protone helmet
Figure 2: Properly worn KASK Protone KP Series helmet during cycling.

Care and Maintenance

  • **Cleaning:** Clean the helmet's exterior with a soft cloth, mild soap, and water. Avoid harsh chemicals, solvents, or abrasive cleaners, as these can damage the helmet's shell or internal components.
  • **Interior Padding:** The internal padding can often be removed and hand-washed with mild soap and water. Allow it to air dry completely before reinserting.
  • **Storage:** Store your helmet in a cool, dry place, away from direct sunlight and heat sources. Do not store it in a car on a hot day, as excessive heat can damage the EPS foam liner.
  • **Inspection:** Regularly inspect your helmet for any signs of damage, such as cracks in the shell, dents in the foam, or frayed straps. If any damage is found, replace the helmet immediately.

Troubleshooting

  • **Helmet feels loose:** Re-adjust the retention system dial/slider and ensure the chin strap is snug. Refer to the 'Adjusting the Fit' section.
  • **Helmet is uncomfortable:** Check for proper placement on your head. Ensure no hair is caught in the straps or retention system. Adjust the padding if possible.
  • **Straps are twisted:** Unbuckle the chin strap and untwist the side straps, ensuring they lie flat against your face.
  • **Visible damage:** If you notice any cracks, dents, or significant wear, the helmet's protective capabilities may be compromised. Replace the helmet immediately.

Specifications

Product dimensions and specifications diagram for KASK Protone KP Series helmet
Figure 3: Detailed product dimensions and specifications.
KASK Protone KP Series Helmet Details
Feature Detail
Model Number KP
Material PC outer shell + EPS foam
Weight Approx. 260g
Head Circumference Universal (52-62cm)
Available Sizes M (52-58cm), L (58-62cm)
Vents 19 holes
Approximate Dimensions (L x H x W) 27cm x 15cm x 21.5cm (Note: Manual measurements, 1-3mm error possible)
Applicable People Unisex
Recommended Age >14 Years
Season Universal
Key Features Precise 1:1 molding, Integrated molding
Available Colors Chameleon, Red Bull, Matte Black, All Red, Tour de France Yellow, Dark Grey, Chocolate, Brown, Green, Black, Clear (Color options may vary by model variant)

User Tips

  • For optimal ventilation, ensure the helmet's internal padding is clean and free of debris.
  • Consider wearing a thin cycling cap or bandana under the helmet for added sweat absorption and comfort, especially in warmer weather.
  • Always double-check the fit and strap tension before every ride, as adjustments can shift over time.

Warranty and Support

For detailed warranty information and customer support, please refer to the official user manual PDF provided by the manufacturer. You can access the PDF document for further guidance:

View User Manual (PDF)

For additional assistance, please contact your retailer or the official KASK support channels.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.