Dash Air Vent Heater Flap Motor Instruction Manual
Model: 6R1907511 / 6R1907511A
1. Introduction
Thank you for choosing the Dash Air Vent Heater Flap Motor. This component is crucial for the proper functioning of your vehicle's heating, ventilation, and air conditioning (HVAC) system. It controls the movement of internal flaps within the dashboard air vents, directing airflow and regulating temperature to ensure passenger comfort. This manual provides general guidelines for installation, operation, maintenance, and troubleshooting. For specific procedures related to your vehicle model, always consult your vehicle's official service manual or a qualified automotive technician.

Figure 1: Dash Air Vent Heater Flap Motor
2. Product Overview
The Dash Air Vent Heater Flap Motor is an electromechanical actuator responsible for adjusting the position of blend doors or flaps within the vehicle's HVAC system. This allows the system to control the mix of hot and cold air, as well as the direction of airflow to different vents (e.g., defrost, face, floor). A malfunctioning flap motor can lead to issues such as incorrect temperature output, air not blowing from the correct vents, or persistent clicking noises from the dashboard.
3. Specifications
| Feature | Detail |
|---|---|
| OEM NO. | 6R1907511, 6R1907511A, 6R2907511A |
| Item Type | Air-conditioning Installation |
| Is it Powered | Non-powered (refers to the motor itself not being a power source) |
| Origin | Mainland China |
| Dimensions (Approx.) | Length: 8.1cm (3.1in), Height: 5.5cm (2.1in) |
| Plug Type | Square 2 Pin Plug |

Figure 2: Product Dimensions
4. Fitment
This Dash Air Vent Heater Flap Motor is compatible with the following vehicle models:
- For VW: Polo 6R (2013-2024)
- For Skoda: Fabia (2011-2023), Rapid (2013-2022)
- For Seat: Ibiza (2013-2017), Toledo (2013-2019)
- For Audi: A1 (2011-2018)
Always verify the OEM part number (6R1907511, 6R1907511A, 6R2907511A) against your existing part to ensure correct fitment.
5. Setup (Installation)
Disclaimer: Installation of automotive components can be complex and may require specialized tools and knowledge. Improper installation can lead to damage to the vehicle or injury. It is highly recommended that installation be performed by a qualified automotive technician or by carefully following your vehicle's specific service manual.
5.1 Installation Preparation
- Ensure the vehicle is turned off, the ignition is removed, and the battery is disconnected to prevent electrical shorts or accidental activation.
- Gather necessary tools, which may include screwdrivers, trim removal tools, sockets, and a flashlight.
- Locate the existing flap motor. Its position varies significantly by vehicle model and the specific flap it controls (e.g., blend door, mode door). This often requires removing dashboard trim panels.
5.2 Installation Steps (General)
- Carefully remove any dashboard trim panels or components obstructing access to the flap motor. Use trim removal tools to avoid damaging plastic parts.
- Disconnect the electrical connector from the old flap motor.
- Remove the mounting screws or clips securing the old flap motor. Note its orientation before removal.
- Gently detach the old motor from the flap linkage. Ensure the flap itself is not damaged.
- Align the new flap motor with the flap linkage and secure it with the original mounting screws or clips. Ensure the motor's gear engages correctly with the flap mechanism.
- Reconnect the electrical connector to the new motor.
- Before reassembling all trim panels, reconnect the vehicle battery and test the HVAC system to ensure the new motor operates correctly across all settings (temperature, vent modes). Listen for any unusual noises.
- Once confirmed operational, reassemble all dashboard trim panels and components in reverse order of removal.
6. Operating
The Dash Air Vent Heater Flap Motor operates automatically as part of your vehicle's HVAC system. There is no direct user interaction with the motor itself. When you adjust the temperature settings, fan speed, or vent mode (e.g., defrost, face, floor) via your vehicle's climate control panel, the vehicle's computer (HVAC control module) sends signals to the flap motors to move the internal flaps to the desired positions.
Ensure your vehicle's climate control system is functioning correctly. If you notice discrepancies in temperature control or airflow direction after installation, refer to the troubleshooting section.
7. Maintenance
The Dash Air Vent Heater Flap Motor is a sealed unit and generally requires no routine maintenance. However, periodic inspection can help ensure its longevity and proper function:
- Visual Inspection: During other dashboard-related maintenance, visually inspect the motor and its wiring for any signs of damage, corrosion, or loose connections.
- Cleanliness: Keep the area around the motor free from excessive dust or debris, which could potentially interfere with its operation or cause premature wear.
- Listen for Noises: If you hear persistent clicking, grinding, or whirring noises from behind the dashboard when adjusting HVAC settings, it may indicate an issue with the flap motor or its linkage.
8. Troubleshooting
If you experience issues with your vehicle's HVAC system that you suspect are related to the flap motor, consider the following common problems and solutions:
| Symptom | Possible Cause | Action |
|---|---|---|
| Air not blowing from correct vents (e.g., stuck on defrost) | Mode door actuator failure | Check electrical connection; replace motor if faulty. |
| Temperature not changing (stuck on hot or cold) | Blend door actuator failure | Check electrical connection; replace motor if faulty. |
| Clicking or grinding noise from dashboard when adjusting HVAC | Stripped gears in motor, motor not fully seating, or obstruction | Inspect motor and linkage for obstructions; replace motor if gears are stripped. |
| No response from HVAC controls | Electrical issue, HVAC control module failure, or multiple motor failures | Check fuses; consult a professional for diagnosis. |
If troubleshooting steps do not resolve the issue, it is recommended to seek assistance from a certified automotive technician.
9. Safety Warnings
- Always disconnect the vehicle's battery before performing any electrical work to prevent injury or damage to electrical components.
- Use appropriate personal protective equipment (PPE) such as gloves and eye protection during installation.
- Ensure all electrical connections are secure and properly insulated to prevent short circuits.
- Do not force the motor into position; ensure proper alignment to avoid damaging the motor or the flap linkage.
- If you are unsure about any step of the installation process, consult a professional mechanic.
10. Warranty and Support
This product is covered by a limited warranty provided by Racbox. Please refer to the images below for detailed warranty terms and conditions.
10.1 Standard Warranty

Figure 3: Racbox Standard Warranty and Period
10.2 Warranty Coverage and Service

Figure 4: What is Covered, Not Covered, and How to Get Service
For warranty service or support, please contact the seller or manufacturer with your purchase invoice and installation records.
11. User Tips
- Double-Check Fitment: Always compare the OEM part number on your old motor with the replacement part number before starting installation.
- Document Disassembly: Take photos or videos during the disassembly process, especially when removing dashboard trim, to aid in reassembly.
- Test Before Final Assembly: Before putting all the trim back, perform a functional test of the HVAC system to ensure the new motor is working correctly. This saves time if adjustments or further troubleshooting are needed.
- Gentle Handling: Automotive plastic trim and internal components can be fragile. Use appropriate trim removal tools and avoid excessive force.