COXO COB/SMD LED Strip

Contents

Dimmable LED Neon Strip Light User Manual

Model: COB/SMD LED Strip

Brand: COXO

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Dimmable LED Neon Strip Light. Designed for both indoor and outdoor applications, this flexible and super bright LED strip offers versatile lighting solutions with its IP67 waterproof rating and dimmable functionality. Please read this manual thoroughly before use to ensure safe and optimal performance.

COXO Dimmable LED Neon Strip Light, IP67 Waterproof, 2700 lm/m

Image: COXO Dimmable LED Neon Strip Light, highlighting its IP67 waterproof rating and 2700 lm/m brightness.

2. Safety & Warnings

  • Always follow installation and operation guidelines to avoid injury.
  • Inspect the product before each use; do not use if damaged.
  • Do not turn on the LED strip when it's rolled together. The strip should be spread out to ensure proper heat dissipation.
  • Do not expose the LED strip to water or moisture unless it is explicitly stated as a waterproof strip. This product is IP67 rated for water resistance.
  • 12V and 24V LED strip lights are not designed for direct connection to 110V/220V AC electricity. Only high voltage 110V/220V LED strips can be connected directly to mains power. Always use a suitable power supply.

3. Package Contents

Your package should contain the following items:

  • 1 x 5-meter (16.4ft) Neon LED Strip Light

Note: A 24V power supply, RF remote + dimmer controller, power cords, and screwdriver are not included and must be purchased separately for full functionality.

4. Setup Instructions

A simple installation requires an LED light strip, a proper power supply, and in some cases, LED wires and a dimmer controller. Ensure all components are rated for DC24V.

4.1. Wiring Diagram Overview

The following diagram illustrates the two main connection methods for the LED strip light. A 24V 5A power supply is required for a 5m (16.4ft) strip and is not included.

Wiring diagram for COXO LED Neon Strip Light showing hard-wired connection to a 24V 150W power supply and direct connection to a DC 24V 5A power adapter.

Image: Wiring diagram for the LED Neon Strip Light, detailing connections to a power supply (hard-wired) or a power adapter (direct connection). Note the requirement for a 24V 5A power supply for a 5m strip.

4.2. Connection Steps

For a visual guide, please refer to the connection instruction video below.

Video: LED strip light connection instruction, demonstrating the wiring process and dimmer control.

  1. Connect Power Supply to Mains: Connect one end of the 24V power supply to the 110V/220V home electricity. Ensure the power supply provides the proper voltage and sufficient amperage for the light strip.
  2. Connect Power Output to Controller (Optional): If using a dimmer controller, connect the power output terminals of the power supply to the input terminals of the controller. Pay close attention to positive (+) and negative (-) polarities. Incorrect connection can damage the LEDs.
  3. Connect LED Strip to Controller/Power Supply: Connect the LED strip to the output terminals of the controller (if used) or directly to the power supply's output terminals. Again, ensure correct polarity (+ to + and - to -).
  4. Secure Installation: The LED strip features a stickable back for easy mounting. For more secure installations, use the included mounting clips and screws.
Image showing the LED strip light being cut and installed using adhesive and mounting clips.

Image: Demonstrates the cuttable design, flexibility, and silicone material of the LED strip, along with installation methods using adhesive and mounting clips.

5. Operating Instructions

5.1. Power On/Off and Dimming

Once properly installed and connected to a compatible dimmer controller (not included), you can control the LED strip light's power and brightness.

Image showing different brightness levels of the LED strip light from 20% to 100% with a dimmer control.

Image: Visual representation of the dimmable feature, showing brightness levels from 20% to 100% controlled by a dimmer.

  • Use the dimmer controller to turn the LED strip light on or off.
  • Adjust the light intensity smoothly from 1% to 100% to meet your desired ambiance.

5.2. Color Temperature Options

The LED strip is available in various color temperatures to suit different preferences and applications:

  • 3000K Warm White
  • 4000K Natural White
  • 5000K White
  • 6000K Cold White
Image displaying the different color temperatures available for the LED strip: 3000K Warm White, 4000K Natural White, 5000K White, and 6000K Cold White.

Image: Comparison of different color temperatures (3000K Warm White, 4000K Natural White, 5000K White, 6000K Cold White) for the LED strip.

6. Maintenance

  • Cleaning: Gently wipe the LED strip with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners. Ensure the strip is powered off before cleaning.
  • Inspection: Periodically check the strip for any signs of damage, such as cuts, cracks, or loose connections. If any damage is found, discontinue use and consult a qualified technician.
  • Storage: If storing the strip, ensure it is not tightly rolled or bent at sharp angles to prevent damage to the internal components.

7. Troubleshooting

ProblemPossible CauseSolution
LED strip does not light up.No power, incorrect wiring, faulty power supply/controller.Check power connections, ensure correct polarity, test power supply/controller.
LED strip flickers.Loose connection, insufficient power, incompatible dimmer.Secure all connections, ensure power supply meets wattage requirements, use a compatible dimmer.
LED strip is dim.Dimmer setting too low, insufficient power, aging LEDs.Adjust dimmer to higher brightness, verify power supply output, consider replacement if very old.
Portions of the strip are not lighting up.Damage to a segment, internal wiring issue.Inspect the damaged segment. If cuttable, isolate the faulty section. Contact support if under warranty.

8. Specifications

The COXO Dimmable LED Neon Strip Light boasts high efficiency and durability. Refer to the table below for detailed technical specifications.

Technical Specification table for COXO LED Neon Strip Light, detailing input voltage, LED type, color temperature, lumens, wattage, CRI, IP rating, adhesive, strip width, length, cut segment, view angle, operating temperature, lifespan, and UL rating.

Image: Detailed technical specifications table for the LED Neon Strip Light.

FeatureDetail
Product NameLED Strip
ModelCOB/SMD LED Strip
LED ModelNeon Strip Light (SMD2835)
Strip Length5m / 16.4ft
LED Quantity240 LEDs/m
Working VoltageDC24V
Power20W/m (approx. 6W/ft)
Luminous Flux2700lm/m (approx. 793lm/ft)
PCB Width12mm / 0.47in
PCB Height5mm
Color Rendering Index (CRI)>90
SDCM<5
DimmableYes
Strip Thickness3OZ Copper PCB
Cutting Length33mm / 1.3in (every 1.3in cuttable)
Lifespan>50,000 hours
Protection RateIP67 Waterproof
ApplicationIndoor & Outdoor
Working Temperature-20℃ to 50℃
CertificationsCE, UL, RoHS, ERP, BIS, EMC, LVD
Warranty5 years
Special FeaturesFlame Resistant, UV Resistant, IK08 Protection, Saltwater Resistant, Flexible, Anti-Yellowing Food Grade Silicone
Image highlighting durability features of the LED Neon Strip Light: Flame Resistant, UV Resistant, IP67 Waterproof, IK08 Protection, Saltwater Resistant, Bending Diameter, and Beam Angle.

Image: Key durability and design features of the LED Neon Strip Light.

9. User Tips

  • For optimal brightness and longevity, ensure your power supply is adequately rated for the total length of the LED strip used.
  • When planning your installation, consider the flexibility of the strip. While highly flexible, avoid extreme sharp bends to prevent damage.
  • If installing outdoors or in wet environments, double-check all connections are properly sealed and the IP67 rating is maintained.
  • Experiment with different dimmer settings and color temperatures to create various moods and lighting effects in your space.

10. Warranty & Support

This COXO LED Neon Strip Light comes with a 5-year warranty, ensuring long-term reliability and performance. For any technical assistance, troubleshooting, or warranty claims, please contact COXO Official Store customer support.

For additional information and detailed documentation, you may refer to the official user manual PDF: User Manual (PDF).

Manufacturer: Shenzhen Coxo Technology Co., Limited
EU Representative: KD EUROPE

Certifications: CE, UL, RoHS, ERP, BIS, EMC, LVD

11. Frequently Asked Questions (FAQ)

Q: Is the LED strip truly waterproof?

A: Yes, the LED Neon Strip Light has an IP67 waterproof rating, making it suitable for both indoor and outdoor use. It is designed to withstand dust and temporary immersion in water.

Image showing the COXO LED Neon Strip Light submerged in water, demonstrating its IP67 waterproof capability.

Image: The LED Neon Strip Light submerged in water, illustrating its IP67 waterproof feature.

Q: Can I cut the LED strip to a shorter length?

A: Yes, the strip features a cuttable design, allowing you to cut it every 33mm (1.3 inches) at designated marks. Ensure to seal the cut end properly if used in a wet environment.

Q: Do I need a special power supply?

A: Yes, a DC24V power supply is required. The power supply is not included with the strip and must be purchased separately. Ensure the power supply's wattage matches or exceeds the total wattage of your LED strip length.

Q: How bright is this LED strip compared to others?

A: This LED strip offers high efficiency and brightness, rated at 2700lm/m. It is designed to provide superior illumination compared to many standard LED strips.

Comparison image showing the high efficiency and brightness of COXO LED strip versus other brands, with COXO rated at 2600 LM/m (793 lm/ft) and 6 W/ft.

Image: Brightness comparison between COXO LED strip and other brands, highlighting COXO's high efficiency.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.