BALASHOV Automatic Sense Soap Dispenser

Contents

BALASHOV Automatic Foam Soap Dispenser

User Instruction Manual

Introduction

Thank you for choosing the BALASHOV Automatic Foam Soap Dispenser. This device provides a hygienic and convenient way to dispense foam soap, suitable for kitchens, bathrooms, and offices. Please read this manual carefully before use to ensure proper operation and maintenance.

Product Overview

The dispenser features infrared sensing for touchless operation, a Type-C rechargeable battery, and an RGB indicator light system for clear status updates.

Automatic soap dispenser dispensing foam into a hand.

Figure 1: Automatic soap dispenser dispensing foam into a hand.

Close-up of the soap dispenser's top panel showing the RGB tri-color light display indicating charging, power-on, and working status.

Figure 2: Close-up of the dispenser's top panel with RGB tri-color light display for status indication.

Key Features:

  • Inductive Cleanliness: Touch-free operation.
  • Smart and Convenient: Easy to use and maintain.
  • Food Grade ABS Material: Safe and durable.
  • 0.2 Second Intelligent Sensing: Quick foam dispensing.
  • Dual Installation Modes: Desktop or Wall-mounted.

Specifications

FeatureDetail
Product NameAutomatic Soap Dispenser / Hand Sanitizer Foam
MaterialABS
Input VoltageDC 5V
Power4W
Battery Capacity1200mAh
Charging InterfaceType-C
Charging TimeApproximately 4 hours
Charging Current1A
Capacity350ml
Operating MethodInfrared Sensing
OriginMainland China

Setup

Initial Preparation

  1. Before using the product for the first time, please fully charge it using the provided Type-C cable. A red light stays on while charging.
  2. Rotate the main unit counter-clockwise to detach it from the bottle body.
  3. Fill the bottle with foam soap and water in a ratio of 1:6 to 1:10. Ensure you use foam hand sanitizer; do not use non-foam hand sanitizer.
  4. Reattach the main unit to the bottle body by rotating clockwise until secure. Shake well to mix the solution.

Installation Options

This dispenser supports both desktop placement and wall-mounted installation.

Image illustrating the dual installation modes (desktop and wall-mounted) of the soap dispenser, highlighting punch-free installation.

Figure 3: Dual installation modes: Desktop and Wall-mounted.

Desktop Placement

Simply place the dispenser on a flat, stable surface near your sink or desired location.

Wall-Mounted Installation (No-Drill)

  1. Clean and dry the desired wall surface thoroughly.
  2. Peel off the adhesive protective film from the back of the buckle base.
  3. Stick the buckle base firmly onto the prepared wall surface. Press firmly for a few seconds to ensure good adhesion.
  4. Hang the dispenser unit onto the installed buckle base, ensuring it is securely seated.

Operating Instructions

Power On/Off

  • To Turn On: Press and hold the power button (located on top) for 2 seconds. The green light will turn on for 3 seconds, then turn off.
  • To Turn Off: Press and hold the power button for 2 seconds. The red light will turn on for 3 seconds, then turn off.

Dispensing Foam

Once powered on, simply place your hand under the dispenser's sensor. The dispenser will automatically dispense foam within 0.2 seconds.

Adjusting Foam Volume (Modes)

The dispenser has three foam volume modes. You can switch between these modes by tapping the power button while the device is on:

  • Mode 1: Blue light on for 0.5 seconds (least foam).
  • Mode 2: Blue light on for 1 second (medium foam).
  • Mode 3: Blue light on for 1.5 seconds (most foam).

Indicator Light Status

  • Charging Status: Red light stays on while charging.
  • Low Battery: Red light flashes.
  • Power-On State: Green light briefly illuminates when turned on.
  • Working Status: Blue light indicates the selected foam volume mode.

Maintenance

Automatic Cleaning Mode

To clean the internal pump and nozzle:

  1. Before activating cleaning mode, replace the soap solution in the bottle with clean water.
  2. While the device is powered on, press and hold the power button for 5 seconds.
  3. The green and blue lights will flash alternately for 60 seconds, indicating the cleaning cycle is active.
  4. You can tap the power button again to stop the cleaning mode early if desired.
Top of the soap dispenser showing the touch button and LED indicators for charging, power, and work status, illustrating the one-click cleaning feature.

Figure 4: Activating one-click intelligent cleaning.

General Care

  • Do not immerse the product in water or rinse it directly with water. Use a damp cloth to wipe the exterior.
  • Avoid direct sunlight or proximity to heat sources for this product.
  • If you do not use this product for a long time, it should be charged and used every three months to maintain battery health.

Troubleshooting

  • Dispenser not turning on: Ensure the device is fully charged. Press and hold the power button for 2 seconds.
  • No foam dispensed: Check if the device is powered on. Ensure there is enough soap solution in the bottle. Verify that the solution is a foam-type soap and mixed in the correct ratio (1:6-1:10 soap to water). Clean the nozzle using the automatic cleaning mode.
  • Weak foam: Adjust the soap-to-water ratio (try slightly more soap). Ensure the battery is not low.
  • Indicator lights not working: Ensure the device is charged and powered on. If issues persist, contact support.

User Tips

  • For optimal foam consistency, experiment with the soap-to-water ratio within the recommended 1:6 to 1:10 range.
  • Fully charge the dispenser before its first use to ensure maximum battery life and performance.
  • Regularly use the automatic cleaning mode with water to prevent clogs and maintain hygiene.

Warranty & Support

For any issues not covered in this manual or for further assistance, please contact your retailer or the manufacturer's customer support. Keep your purchase receipt for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.