1. Introduction
The Tactical X300U-A is a high-performance weapon-mounted flashlight designed for tactical applications. Featuring a powerful LED light source, multiple operating modes, and a robust metal construction, it provides reliable illumination for various scenarios. This manual provides essential information for the safe and effective use of your flashlight.

Figure 1: Tactical X300U-A Flashlight with 1000LM output.
2. Safety Information
WARNING: Read all safety warnings and instructions carefully before use.
- Eye Safety: Do not shine the flashlight directly into human eyes (especially children's eyes), as this may cause temporary or permanent vision damage.
- Heat and Fire: Keep the product away from high temperatures, open flames, and flammable materials to prevent battery overheating, explosion, or fire.
- Battery Handling: Do not disassemble, modify, or puncture the battery. Replace batteries only with the same model/specification.
- Choking Hazard: Keep the flashlight and its small parts out of reach of infants and young children to prevent choking or accidental injury.
- Charging: Do not charge the flashlight with an uncertified charger to prevent short circuits.
- Choking Hazard - Small parts. Not for Children under 3 years.
3. Package Contents
Please check the package for the following items:
- 1 x Tactical X300U-A Flashlight
- 1 x Storage Case
- 1 x Hex Key
Note: Batteries are NOT included and must be purchased separately.

Figure 2: Included package contents (batteries not included).
4. Setup
4.1 Battery Installation
- Rotate the battery compartment cover (tail/lamp end) counterclockwise to unscrew and open.
- Insert two 16340 or CR123A batteries according to the positive (+) and negative (-) polarity marks inside the compartment. Ensure correct orientation to prevent damage.
- Tighten the cover clockwise to ensure tight contact. A loose cover may cause the flashlight to malfunction.
4.2 Mounting on Rail
The X300U-A flashlight is designed to fit standard 20mm Picatinny rails.
- Align the flashlight's rail clamp with the desired slot on your 20mm Picatinny rail.
- Secure the flashlight to the rail using the integrated mounting mechanism. Ensure it is firmly attached to prevent movement during use.

Figure 3: Illustrative diagram of the flashlight mounted on a rail.
5. Operating Instructions
5.1 Power On/Off
- Turn On: Press the tail/side switch once to turn on the light. It defaults to high brightness mode.
- Turn Off: Press and hold the switch for 2 seconds to turn off the flashlight directly (works in all light modes).
5.2 Mode Switching
After turning on the flashlight, click the switch quickly to cycle through the available modes:
- High brightness
- Low brightness
- Strobe
- SOS
5.3 Constant and Momentary Operation

Figure 4: Operating modes for momentary and constant light.
- Momentary: Tap the switch for temporary illumination. The light will stay on as long as the switch is pressed.
- Constant: Rotate the switch up or down to engage constant illumination. The light will remain on until the switch is returned to the off position.
5.4 Charging Operation (For Rechargeable Batteries)
If you are using rechargeable 16340 batteries, follow these steps:
- Connect a compatible USB cable (Type-C/Micro USB) to the flashlight's charging port.
- Connect the other end of the USB cable to a 5V USB power source (e.g., charger, power bank, computer USB port).
- The charging indicator light will be red while charging. It will turn green or blue when fully charged. Avoid overcharging for more than 24 hours.
- Unplug the cable immediately after the batteries are fully charged to protect battery life.
6. Maintenance
- Cleaning: Wipe the flashlight body with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Battery Care: If the flashlight will not be used for an extended period, remove the batteries to prevent leakage and corrosion.
- Storage: Store the flashlight in a cool, dry place away from direct sunlight and extreme temperatures.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Flashlight does not turn on | Batteries incorrectly installed or depleted; battery compartment cover loose. | Check battery polarity and ensure they are charged. Tighten the battery compartment cover. |
| Low light output or flickering | Low battery charge; poor battery contact. | Replace or recharge batteries. Ensure batteries are clean and making good contact. |
| Mode switching issues | Switch not fully pressed or debris in switch mechanism. | Ensure firm clicks when pressing the switch. Clean around the switch area. |
8. Specifications
| Feature | Specification |
|---|---|
| Product Name | Tactical X300U Flashlight |
| Light Source | LED bulbs |
| Brightness | 1000 Lumens (LM) |
| Fitment | 20mm Picatinny Rail |
| Functions | Constant / Momentary, High, Low, Strobe, SOS |
| Battery Type | 2 x 16340 or 2 x CR123A (Not included) |
| Dimensions (Length) | 96mm / 3.78 inches |
| Dimensions (Diameter) | 28mm / 1.1 inches |
| Weight | Approx. 0.32 kg |
| Origin | Mainland China |

Figure 5: Product dimensions.
9. User Tips
- Upon receiving your flashlight, carefully inspect the switch mechanism to ensure it operates smoothly and without obstruction.
- Familiarize yourself with the different light modes, including strobe timing and brightness levels, to best suit your operational needs.
- Always use high-quality batteries of the specified type for optimal performance and safety.
10. Warranty and Support
For any warranty claims, technical support, or inquiries regarding your Tactical X300U-A flashlight, please contact the seller or retailer from whom you purchased the product. Please refer to your purchase documentation for specific warranty terms and contact information.
For additional information, you may refer to the official user manual PDF available at: User Manual (PDF)