Godox AD800Pro

Contents

Godox AD800Pro 800Ws TTL Outdoor Flash Instruction Manual

Thank you for purchasing the Godox AD800Pro. This all-in-one outdoor flash offers strong power, a detachable lithium battery pack, and great portability. It integrates with the Godox 2.4G wireless X system for versatile control and compatibility with various camera systems.

Important Safety Instructions

This product is professional photographic equipment and should be operated by professional personnel only. Please read and understand all safety instructions before use to prevent injury or damage.

General Safety Precautions

  • Always remove all transport protective materials and packaging before use.
  • High voltage exists when the flash is powered on. Internal capacitors remain charged for some time after power off.
  • Children must be closely supervised when near the fixture to prevent injury. This is not a toy.
  • Do not use this fixture for general illumination. Avoid looking directly at the flash, especially if you have eye damage or sensitivity.
  • Exercise extreme caution; do not touch high-temperature parts like flash tubes and metal components to avoid burns.
  • Do not point the flash directly at eyes, especially infants'. Turn off immediately if discomfort occurs and seek medical attention.
  • If the flash tube is damaged, stop use immediately and contact service personnel for replacement.
  • Do not use damaged equipment or accessories. Ensure professional inspection and repair before continued use.
  • Disconnect power or remove batteries before replacing flash tubes, protective glass, or fuses. Allow 10 minutes to cool and wear insulated/heat-resistant gloves.
  • Turn off power before connecting or disconnecting plugs. Ensure plugs are fully inserted.
  • Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid electric shock.
  • Place power cords properly to avoid contact with heat sources or tripping hazards. Use original power cords; damage from non-original cords is not covered by warranty.
  • Unplug the power cord from the socket before cleaning or maintenance. Pull by the plug end, not the cord.
  • This device is not waterproof. Keep it dry and avoid immersion in water or other liquids. Install in a ventilated, dry location. Do not place items above it or allow liquids to flow into it.
  • Do not disassemble without authorization. Repairs must be done by Godox or authorized personnel.
  • Before storing, ensure the device has cooled down and the power cord is unplugged. Store in a protective case or ventilated dry location.
  • Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases.
  • Do not use or store this device in potentially explosive environments.
  • Do not cover the heat dissipation port.
  • Do not use unapproved accessories, as this may cause fire, electric shock, or personal injury.
  • Clean gently with a dry cloth. Do not use a wet cloth.
  • Some products are equipped with protective covers that must be removed before use.

Battery Safety Instructions

  • Danger of explosion if the battery is replaced improperly. Replace only with the same or equivalent type by service personnel. Do not disassemble the product or battery.
  • Do not expose the battery to sunlight, fire, or excessive heat. Do not expose to rain or water.
  • Do not disassemble, hit, crush, or throw the battery into fire. Do not use if seriously inflated.
  • When using, place the device in a well-ventilated area. Do not place on bedding or in enclosed spaces. Keep out of reach of children.
  • Do not short circuit battery contacts.
  • Do not charge continuously for over 8 hours.
  • Store in dry, cool, ventilated places.
  • Dispose of dead batteries according to local regulations.
  • Recharge the battery every three months if not in use.
  • If battery fluid leaks, avoid contact. If fluid contacts eyes, rinse with water for at least 15 minutes and seek medical attention.

Main Features

  • Quick Recycle Time: Approximately 0.01s (minimum power) to 1.5s (full power).
  • Stable Color Temperature: Shift around ±100K over the entire power range.
  • LED Modeling Lamp: 40W bi-color large LED modeling light with adjustable brightness and CCT.
  • Studio Quality Light: Up to 800Ws, approximately 300 full power flashes per charge, with 1/8000s high-speed sync.
  • Precise Power Adjustment: From full power 1/1 to 1/512 with 0.1 increment per step.
  • Wide Compatibility: Fully supports M, Multi, and wireless TTL flash systems for Canon, Nikon, Fujifilm, OM SYSTEM, Sony, Leica, Pentax, etc. Functions as a receiver unit in a wireless flash group.
  • Wireless Control: Built-in 2.4G wireless X system for remote control via optional Godox flash triggers, and a 3.5mm sync cord jack for various sync triggering modes.
  • Distinct Group Colors: 16 groups with different colors for quick distinction in remote usage.
  • Simple Operation: Features a 2.8" color screen and a steplessly rotatable select dial. Detachable battery pack design.
  • Wide-range Accessories: Bowens mount ensures wide compatibility with various light modifiers.
Godox AD800Pro Outdoor Flash with key features highlighted
Overview of the Godox AD800Pro Outdoor Flash highlighting its main features like 800Ws power, 1/35710s flash duration, 300 full-power flashes, 0.01-1.5s recycle time, 1/512 fine power control, and 40W bi-color modeling lamp.
Godox AD800Pro with AC adapter and UC-46 charger
The AD800Pro supports flexible power solutions, including an optional AC26 adapter for continuous AC power and a UC-46 fast charger for quick battery charging.

What's Inside

The package includes the following items:

Contents of the Godox AD800Pro package
An image showing the contents of the Godox AD800Pro package, including the flash body, flash tube, battery, adapter, power cord, reflector, and reflector protection cover.
  • Flash Body × 1
  • Flash Tube × 1
  • Battery × 1
  • Adapter × 1
  • Power Cord × 1
  • Reflector Protection Cover × 1
  • Reflector × 1
  • Instruction Manual × 1

Name of Parts

Familiarize yourself with the different parts of your AD800Pro flash unit:

Diagram of Godox AD800Pro flash body with numbered parts
Detailed diagram of the AD800Pro flash body, indicating various components such as the flash tube, color screen, buttons, dials, ports, and indicators.
  1. Flash Tube
  2. Color Screen
  3. MENU Button
  4. MODE Button
  5. Select Dial
  6. SET Button
  7. Power Switch/Test Button
  8. Modeling Lamp Button
  9. Bracket Locking Knob
  10. Handle Fixing Fastener
  11. Handle
  12. Accessory Locking Pusher
  13. USB-C Port (firmware upgrade/insert FR433 receiver)
  14. 3.5mm Sync Cord Jack
  15. Group Indicator ×2
  16. Photocell Sensor
  17. Battery Indicator Button
  18. Battery Charging Port
  19. Battery Level Indicator
  20. Battery Detaching Pusher
  21. Reflector

Separately Sold Accessories

To enhance your photography experience, consider these optional Godox accessories:

Optional Bowens Mount Accessories for Godox AD800Pro
Various Bowens Mount accessories such as Flash Projection Attachment BFP, Beauty Dish, Barndoor Kit BD-04, Reflectors, Quick Release Umbrella Softbox, Snoot SN-05, Quick Release Parabolic Softbox, and Parabolic Light Focusing System.
Creative Accessory Ecosystem for Godox AD800Pro
The AD800Pro's native Bowens Mount provides access to a wide range of light-shaping tools. An optional H600P Extension Head with a 2m cable allows for flexible light placement.
  • Flash Head: H600P Portable Flash Head
  • Power Source: AC26 AC Power Source, UC46USB Power Adapter
  • Flash Trigger: XPro, XProII, X2T, X3 series
  • Optical Accessories: Umbrella Softbox, Collapsible Lantern Softbox, Quick-loading Parabolic Softbox, Beauty Dish, Umbrella Diffuser, Snoot, Light Stand, etc.

Setup

Installing and Disassembling Reflector/Flash Tube

Installing the Reflector: Insert the reflector into the accessory mount, press and hold, then rotate clockwise until it locks. The accessory locking pusher will lock up.

Disassembling the Reflector: Press down the accessory locking pusher, then rotate the reflector anticlockwise to unlock.

Installing the Flash Tube: Press down the accessory locking pusher, remove any other accessories. Match the flash tube with the tube socket and push until it is securely seated.

Disassembling the Flash Tube: Press down the accessory locking pusher, remove any other accessories. Grasp the flash tube and pull it out horizontally.

Note: Always power off the unit and wear gloves when handling the flash tube for safety.

Diagrams for installing and disassembling reflector and flash tube
Visual guide for attaching and detaching the reflector and flash tube from the AD800Pro unit.

Adjusting Flash Angle

  1. Rotate the handle anticlockwise to unlock it. Adjust the flash body to the desired angle, then rotate the handle clockwise to tighten.
  2. If the handle collides with the flash body during rotation, press the handle fixing fastener and pull out the handle to extend its reach, then repeat step 1.

Loading and Unloading the Battery

Loading: Match the battery's groove with the main battery compartment's ridge. Push down the battery pack until it locks into place.

Unloading: Press the battery detaching pusher and simultaneously push the battery pack upward to release it from the battery compartment.

Diagrams for loading and unloading the battery
Illustrations demonstrating the correct procedure for inserting and removing the battery pack from the AD800Pro flash unit.

Operation

Power Switch

  1. To Turn On: Long press the power switch button until the unlock icon (Unlock icon) is displayed, then rotate the select dial clockwise.
  2. To Turn Off: Long press the power switch button until the panel blacks out.

Note: Turn off the device if it will not be used for an extended period. This device has an automatic power off function, which can be set in the menu settings.

Battery Level Indication

After correctly installing the battery, press the battery indicator button to check the current battery level. The battery level indicator lights will show the charge status:

Battery Level IndicatorMeaning/Percentage of Battery Level
1 red grid + 3 green grids75% ~ 100%
1 red grid + 2 green grids50% ~ 75%
1 red grid + 1 green grid25% ~ 50%
1 red grid3% ~ 25%
2% flash red, 1% off< 2%. The battery level is going to be used out immediately. The flash will alarm for 1 minute and auto power off in 3 minutes. Recharge as soon as possible (within 10 days).

Note: The indications are almost the same except for slight variations during grid shifts.

Battery Instructions

This flash unit uses a li-ion battery with long runtime, providing about 300 full power flashes. The inner circuit is reliably safe against overcharge, overdischarge, overcurrent, and short circuit. A full charge with the standard charger takes approximately 2 hours.

MENU Settings

AD800Pro Smart Tools Effortless Control display
The AD800Pro features an HD Color Screen for smart control, a 40W Bi-color Modeling Lamp, and 16 Color Group Indicators for easy identification.

Press the MENU button to enter the menu interface. Use the select dial and SET button to navigate and adjust settings. The table below outlines the available options:

IconFunctionOptionsNotes
((()))WirelessOff, OnTurn off/on wireless function
④Flash ModeNormal, Color, FreezeNormal flash mode; Stable color temperature mode (non-HSS M mode); Freeze mode (M and Multi mode).
SPhotocellOff, S1, S2Turn off photocell; S1 (M and TTL mode); S2 (M manual flash mode).
HHSSOff, OnTurn off/on high speed sync (M and TTL mode).
◎ModelInter, ContModeling lamp off in triggering; Modeling lamp constant on.
BeepOff, OnBeep is off/on.
AType1/512, 1.0Flash step displays as 1/512-1/1; Flash step displays as 1.0-10.0 in non-HSS mode.
Standby30sec, 1min, 2min, 3minScreen blacks out after idle time.
Auto OffOff, 30min, 60min, 90min, 120minTurn off auto off function; Auto off after idle time.
Brightness20%-100%Rotate the select dial to adjust.
DelayOff, 0.01s-30.0sTurn off delay flash; Rotate the select dial to adjust delay flash.
MaskMask (Off, 2-8), Alt (1-8)Masks and alt must be used in combination. Mask represents total flashes, alt represents nth flash. Multi-selection available.
LanguageChinese, EnglishSimplified Chinese or English operating system.
ResetYes, NoFactory reset or cancel.
Device InfoNo optionDisplay current model and version.

Flash Modes

AD800Pro display screens for TTL, Manual, and Multi flash modes
Examples of the AD800Pro's color screen displaying settings for TTL Auto Flash, Manual Flash (M), and Multi Stroboscopic Flash modes.

TTL Auto Flash

In TTL mode, the camera's metering system detects the flash reflected from the subject and automatically adjusts the flash output for even exposure. This mode is only available when the wireless function is on.

To Turn On Wireless: Press the MENU button, select "Wireless", then SET to turn it on. Set the channel, group, and ID to match the transmitter unit. Press MENU twice to return to the main interface.

To Switch to TTL Mode: Press the MODE button until the screen displays <TTL> in the upper-left corner.

M: Manual Flash

The flash output is adjustable from 1/1 full power to 1/512 power with 0.1 step increments. Use a hand-held flash meter to determine the required flash output for correct exposure.

To Switch to M Mode: Press the MODE button until the screen displays <M> in the upper-left corner.

Power Adjustment: Rotate the select dial to choose the desired flash output amount.

Flash OutputEquivalent (0.1 to 0.9 increments)
1/5121/512 (0.1 to 0.9)
1/2561/256 (0.1 to 0.9)
1/1281/128 (0.1 to 0.9)
1/641/64 (0.1 to 0.9)
1/321/32 (0.1 to 0.9)
1/161/16 (0.1 to 0.9)
1/81/8 (0.1 to 0.9)
1/41/4 (0.1 to 0.9)
1/21/2 (0.1 to 0.9)
1/1(full power)

Multi: Stroboscopic Flash

Stroboscopic flash fires a rapid series of flashes to capture multiple images of a moving subject in a single photograph. You can set the flash output, number of flashes, and flash frequency (Hz).

  1. Press the MODE button until <Multi> is displayed. Turn the select dial to choose the desired flash output.
  2. Press the SET button and turn the select dial to set the number of flashes.
  3. Press the SET button again and turn the select dial to set the flash frequency.

Calculating Shutter Speed: During stroboscopic flash, the shutter remains open until firing stops. Use the formula: Number of Flashes / Flash Frequency = Shutter Speed. For example, 10 flashes / 5 Hz = 2 seconds shutter speed.

Note: Stroboscopic flash is most effective with a highly reflective subject against a dark background. A tripod and TTL flash trigger are recommended. Flash output of 1/1 and 1/2 cannot be set. Can be used with "bulb" mode.

Flash Output1 Hz2 Hz3 Hz4 Hz5 Hz6-7 Hz8-9 Hz10 Hz11 Hz12-14 Hz15-19 Hz20-50 Hz60-100 Hz
1/45432222222222
1/820151210865444444
1/1630303020202010888888
1/3260606050504030202020181612
1/6490909080807060504040353020
1/1281001001001001009080707060504040
1/2561001001001001009080707060504040
1/5121001001001001009080707060504040

High-Speed Sync (HSS)

High-speed sync (FP flash) allows the flash to synchronize with all camera shutter speeds, which is useful for fill-flash portraits using aperture priority.

To Enable HSS: Press the MENU button, select "High-Speed Sync", then SET to turn it on. The HSS icon <H> will appear on the main interface.

Note: If the shutter speed is equal to or slower than the camera's maximum flash sync speed, <H> will not be displayed. Faster shutter speeds with HSS reduce effective flash range. To return to normal flash, turn off HSS in menu settings. Multi flash mode cannot be set in HSS. Over-temperature protection may activate after 64 consecutive HSS flashes.

Power Output LevelNumber of Flashes (HSS)
1/164
1/2 (+0.3, +0.7)70
1/4 (+0.3, +0.7)90
1/8 (+0.3, +0.7)115
1/16 (+0.3, +0.7)140
1/32 (+0.3, +0.7)180
1/64 (+0.3, +0.7)210
1/128 (+0.3, +0.7)235
1/256 (+0.3, +0.7)255

Flash Duration Display

Flash duration refers to the time from flash firing to reach half peak at maximum. The product uses t=0.1 for more precise data, compared to t=0.5.

Note: Turn off the high-speed sync function in M mode for the flash duration to be displayed.

Modeling Lamp

The AD800Pro is equipped with a 40W bi-color LED modeling lamp. Press the modeling lamp button to enter settings. Use the select dial to choose among Off, Free, or Prop, then SET to adjust parameters.

Level 1 OptionsLevel 2 OptionsNotes
OFF/Turn off the modeling lamp
FREE10%-100% (with 1% increment)Brightness range
2800K-6000K (with 100K increment)CCT range
PROP2800K-6000K (with 100K increment)CCT range, and brightness follows flash power

Wireless (2.4G) Transmission

The AD800Pro uses Godox's 2.4G wireless X system, compatible with other Godox products. It automatically switches to receiver unit mode based on the transmitter unit. Compatible cameras include Canon, Nikon, Sony, OM SYSTEM, Panasonic, Fujifilm, Pentax, Leica, etc.

As a receiver unit, the AD800Pro can be controlled by XPROII, X3, X2T, V1Pro, V1, and V860III series transmitter units.

Wireless Settings: Press MENU, select "Wireless", then SET. Choose among wireless/channel/group/ID/wireless sync. Use the select dial and SET button to adjust parameters. Press MENU twice to return to the main interface.

SettingOptions
WirelessOn/Off
Channel1-32
Group0-9, A-F
IDOff, 1-99
Wireless SyncApprox. 100m wireless transmission

Note: When using a transmitter without wireless sync, channel, group, and ID must be set manually. With wireless sync, these can be set quickly.

Wireless Sync (Example with X3 flash trigger)

  1. Turn off camera, mount X3 on hot shoe, power on X3 and camera.
  2. On X3, slide screen down to <Setting>, press to enter C.Fn. menu, then select <Wireless> and <Wireless Sync>.
  3. On AD800Pro, press MENU, select "Wireless", turn it on, then select "Wireless Sync" with the dial.
  4. Both units' CHs and IDs will automatically be set to the same.
  5. Set flash mode and output power on the X3 trigger.
  6. Press the trigger button on X3 or camera shutter to trigger.
Diagrams for wireless flash shooting with one or multiple receiver units
Illustrations showing auto flash shooting with one receiver unit and multiple receiver units, demonstrating how to set up a wireless flash system.

Godox FT433 Function

For enhanced signal stability and anti-interference, use the Godox FT433 flash trigger (transmitter FT433 and receiver FR433). With a built-in 433MHz wireless module, it offers longer transmission distance and reduced interference. The FT433 is compatible with Canon, Nikon, and Sony cameras, controlling Godox flashes like AD800Pro, AD100ProII, AD200ProII, AD400ProII, AD600ProII, and AD600BMII.

Operation Instructions:

  1. Turn off flash trigger, camera, and flash. Mount FT433 transmitter on camera hot shoe. Insert FR433 receiver into AD800Pro's USB-C port. Rotate antennas out. Power on all devices.
  2. On FT433, press MENU, select <(())> to set channel and ID. Press MENU to return. Press MODE-LOCK to set flash trigger mode and level.
  3. On AD800Pro, press MENU, select "Wireless" with the dial, then SET to enter wireless settings. Turn on wireless, set the same channel, group, and ID as the FT433.
  4. Press camera shutter to trigger. The FT433 status lamp will turn red synchronously.

Note: Flash trigger FT433 is sold separately.

Sync Triggering

The 3.5mm sync cord jack allows the flash to be fired synchronously with the camera shutter by inserting a trigger plug.

Maintenance

Cleaning

Gently clean the device with a dry cloth. Do not use a wet cloth as it may damage the device. Always unplug the power cord before cleaning.

Battery Storage

Charge the battery to about 50% before storage. Charge it to about 50% at least every six months. Failure to perform maintenance charging over an extended period may cause permanent performance degradation. Removable batteries should be stored separately between 0°C and 40°C.

Battery Activation

If the battery has not been used for more than a month, it will automatically enter sleep mode. To reactivate it, short press the battery indicator button.

Troubleshooting

Over-Temperature Protection

To prevent overheating and damage, do not fire more than 64 continuous flashes at 1/1 full power in fast succession. After 64 flashes, allow at least 10 minutes of rest. If more flashes are fired in short intervals, the over-temperature protection may activate, extending recycling time to over 10 seconds. If this occurs, allow 10 minutes of rest for the flash unit to return to normal. When over-temperature protection is active, the icon <Over-temperature icon> is shown on the screen.

Power Output LevelNumber of Flashes (Normal)
1/180
1/2 (+0.7)105
1/2 (+0.3)128
1/2160
1/4 (+0.3, +0.7)210
1/8 (+0.3, +0.7)375
1/16 (+0.3, +0.7)800
1/32 (+0.3, +0.7)1060
1/64 (+0.3, +0.7)2130
1/128 (+0.3, +0.7)2130
1/256 (+0.3, +0.7)2130
1/512 (+0.3, +0.7)2130

Other Protections (Error Codes)

The system provides real-time protection. Refer to these prompts:

DisplayMeaning
Error1A failure occurs on the recycling system so that the flash cannot fire. Restart the flash unit. If the problem still exists, send this product to a maintenance center.
Error3The voltage on two outlets of the flash tube is too high. Send this product to a maintenance center.
Error9Errors occurred during the upgrading process. Use the correct firmware upgrade method.

Reason & Solution of Not Triggering in Godox 2.4G Wireless

  1. Disturbed by 2.4G signal in outer environment (e.g., wireless base station, 2.4G WiFi router, Bluetooth, etc.): Adjust the channel (CH) setting on the flash trigger (add 10+ channels) to find an undisturbed channel, or turn off other 2.4G equipment.
  2. Flash not recycled or caught up with continuous shooting speed, or under over-heat protection: Downgrade the flash power output. If in TTL mode, try changing to M mode.
  3. Distance between flash trigger and flash is too close (< 0.5m): Turn on "short distance wireless mode" on the flash trigger. For X1 Series, press and hold the triggering button then turn on the device until the indicator blinks twice. For XPro and X2T Series, set C.Fn-DIST to 0-30m. For X3 Series, set the triggering distance to 0-30m.
  4. Flash in low battery state: Charge or replace the battery in time, ensuring both devices have enough battery power.
  5. Flash trigger's firmware is an older version: Upgrade the firmware of the flash trigger (refer to its instruction manual).
  6. Camera's firmware is an older version: Upgrade the firmware of the camera (refer to its instruction manual).

Specifications (Technical Data)

Technical Data table for Godox AD800Pro
Detailed technical specifications for the Godox AD800Pro, including flash modes, power, and modeling lamp features.
Technical Data table for Godox AD800Pro (continued)
Continued technical specifications for the Godox AD800Pro, covering wireless features, power supply, dimensions, and weight.
FeatureSpecification
ModelAD800Pro
Wireless Receiver Unit ModeWireless Mode (compatible with Canon E-TTL II, Nikon i-TTL, Sony, OM SYSTEM, Panasonic, Fujifilm, Leica, Pentax)
Flash ModeWireless off: M/Multi; Wireless receiver mode: TTL/M/Multi
Guide No. (1/1 step)110 (ISO 100, in meters, with efficient reflector)
Flash Duration (t=0.1)Normal: 1/350s ~ 1/11400s; Color: 1/350s ~ 1/9220s; Freeze: 1/5020s ~ 1/35710s
Power (1/1 step)800Ws
Power Output10 steps: 1/512 ~ 1/1 (with 0.1 increment each step) Note: 9 steps in CCT mode
Stroboscopic FlashProvided (up to 100 times, 100Hz)
Sync ModeHigh-speed sync (up to 1/8000 seconds), first-curtain sync, and second-curtain sync
Delay Flash0.01 ~ 30s
Mask√
Fan√
Beep√
Flash Duration Indication√
PhotocellS1/S2/OFF
DisplayColor screen
Modeling Lamp
Max. Input Power40W
Brightness Range10%-100%
CRIAverage≥97
TLCIAverage≥98
CCT2800K-6000K
Wireless Flash (2.4G transmission)
Wireless FunctionReceiver, Off
Controllable Receiver Groups16: 0-9, A-F
Transmission RangeApprox. 100m
Channels32: 1-32
ID01-99/OFF
Power Supply
Power SupplyLithium battery (28.8V/2900mAh)
Full Power FlashesApprox. 300
Recycle TimeQuickest approx. 0.01s ~ 1.5s
Battery Level Indicator√
Power SavingAuto off function is available in menu settings (30min to 120min of idle use)
Sync Triggering Mode3.5mm sync cord
Flash Tube Color Temperature5800±200K
Dimensions and Weights
Dimension (with battery, flash tube and reflector)≈4.96"×6.1"×13.5" (126mm×155mm×343mm)
Net Weight (with battery, flash tube and reflector)≈8.16lb (3.7kg)

Specifications and data may be subject to changes without notice.

Firmware Upgrade

  • The flash supports firmware upgrade through the USB-C port. Update information will be released on the official website.
  • Use a USB-C cable (sold separately) for firmware upgrade.
  • Firmware upgrade requires Godox G3 software. Download and install the software from the Godox official website (https://www.godox.com.cn/firmware-G3/) before upgrading. Then, choose the related firmware file.
  • Refer to the latest electronic version of the instruction manual for specific instructions.

User Tips

  • For optimal performance, ensure the battery is fully charged before important shoots.
  • Experiment with different flash modes (TTL, Manual, Multi) to understand their effects and find the best setting for your creative vision.
  • When using wireless triggering, always double-check that the channel, group, and ID settings match between the flash and the trigger to avoid misfires.
  • Utilize the modeling lamp to preview lighting effects before taking a shot, especially in complex setups.
  • Keep the firmware updated to benefit from the latest features and bug fixes.

Warranty and Support

This document applies to the products listed in the Product Maintenance Information. Other products or accessories (e.g., promotional items, giveaways, and additional accessories) are not included in this warranty scope.

Warranty Period

The warranty period for products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the purchase date, which is recorded on the warranty card.

Inapplicable Cases

The guarantee and service are not applicable in the following cases:

  • The product or accessory has exceeded its warranty period.
  • Breakage or damage caused by inappropriate usage, maintenance, or preservation (e.g., improper packing, plugging/unplugging external equipment, falling off, squeezing, exposure to improper temperature, solvents, acids, bases, flooding, damp environments).
  • Breakage or damage caused by non-authorized installation, maintenance, alteration, addition, or detachment.
  • The original identifying information of the product or accessory is modified, altered, or removed.
  • No valid warranty card.
  • Breakage or damage caused by using illegally authorized, nonstandard, or non-public released software.
  • Breakage or damage caused by force majeure or accident.
  • Breakage or damage not attributable to the product itself.

In such cases, Godox assumes no responsibility. Normal discoloration, abrasion, and consumption are not considered breakage within the maintenance scope.

Maintenance and Service Support Information

Product TypeNameMaintenance Period (month)Warranty Service Type
PartsCircuit board12Customer sends the product to designated site
Battery3Customer sends the product to designated site
Electrical parts (e.g., battery charger)12Customer sends the product to designated site
Other ItemsPower cord, Sync cord, flash tube, modeling lamp, shell, lamp cover, locking device, package, etc.NoWithout warranty

Godox After-sale Service Call: 0755-29609320-8062

QC Pass certificate and Godox contact information
QC Pass certificate and contact information for GODOX Photo Equipment Co., Ltd., including address, phone, fax, email, and website.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.