YIHUA 853AAA-I

Contents

YIHUA 853AAA-I Multi-Station Instruction Manual

Model: 853AAA-I

1. Introduction

Thank you for purchasing the YIHUA 853AAA-I Multi-Station. This comprehensive device integrates an LCD screen separator, a hot air rework station, and a soldering station, making it an ideal tool for electronics repair and assembly. This manual provides detailed instructions for safe and efficient operation, maintenance, and troubleshooting. Please read it carefully before use and keep it for future reference.

YIHUA 853AAA-I Multi-Station with accessories

Figure 1: YIHUA 853AAA-I Multi-Station with included accessories.

2. Applications

  • Screen Separation: This station is suitable for separating LCD screens, especially mobile phone screens.
  • Soldering and Desoldering: Ideal for a wide range of components including SOIC, CHIP, QFP, PLCC, BGA, SMD, and more. It is particularly effective for desoldering in-line sockets.
  • Other Applications: Can be used for heat shrinking, drying, paint removal, conformal coating removal, defrosting, preheating, and glue soldering.

3. Specifications

FeatureSpecification
Input Voltage110~127V/AC, 60Hz or 220~240V/AC, 50Hz
Rated Power1180W
Main Unit Dimensions (L×W×H)275×195×130mm ±5mm
Operating Ambient Temperature0~40°C / 32°F~104°F
Screen Separator
Temperature Range50~120°C / 122~248°F
Heating Surface Area200×110mm ±5mm
DisplayNixie LED
Hot Air Rework Station
Air DeliveryBrushless motor with smooth air delivery
Output Air Volume≤120L/min
Temperature Range100~480°C / 212~896°F
DisplayNixie LED
Soldering Station
Temperature Range200~480°C / 392~896°F
DisplayNixie LED
Tip to Ground Resistance<2 Ohms

4. Reference Diagram & Components

Familiarize yourself with the various parts of your YIHUA 853AAA-I Multi-Station:

Control panel diagram of YIHUA 853AAA-I Multi-Station

Figure 2: Front panel and component layout of the YIHUA 853AAA-I Multi-Station.

  1. Temperature Display (Screen Separator)
  2. Temperature Display (Hot Air Rework Station)
  3. Temperature Display (Soldering Station)
  4. Sleep Mode Indicator
  5. Simulated Air Volume
  6. Suction Pump Indicator
  7. Aluminum Heating Plate
  8. Power Switch (Screen Separator)
  9. Temperature Adjustment Knob (Screen Separator)
  10. Air Volume Adjustment Knob
  11. Power Switch (Hot Air Rework Station)
  12. Temperature Adjustment Knob (Hot Air Rework Station)
  13. Temperature Adjustment Knob (Soldering Station)
  14. Power Switch (Soldering Station)
  15. Hot Air Gun's Receptacle (or Hot Air Gun's Cord)
  16. Receptacle (Soldering Iron)
  17. Suction Activation Button
  18. USB Port
  19. Power Switch (Main)
  20. Hot Air Gun Holder

5. Initial Setup

  1. Unpacking: Carefully remove all components from the packaging. Inspect for any damage.
  2. Placement: Place the main unit on a stable, heat-resistant surface with adequate ventilation. Ensure there is enough space around the unit for safe operation.
  3. Hot Air Gun Holder: Install the hot air gun holder onto the left side of the station.
  4. Power Connection: Connect the station's power cord to an appropriate electrical outlet (110~127V/AC, 60Hz or 220~240V/AC, 50Hz, depending on your model).

6. Operating Instructions

6.1. Screen Separator

  1. Place the silicone gel pad onto the aluminum heating plate, aligning its holes with the plate's holes.
  2. Turn ON the main power switch (19), then turn ON the Screen Separator power switch (8).
  3. Use the Temperature Adjustment Knob (9) to set the desired temperature, typically around 80°C/176°F for initial heating. The plate will begin heating.
  4. CAUTION: Do not set the temperature too high to avoid damaging the screen due to overheating. The operation indicator (dot at bottom-right of screen) turns ON when heating, blinks when stable, and turns OFF when cooling.
  5. Once the temperature stabilizes, place the screen onto the silicone gel pad, covering the holes.
  6. Turn ON the Suction Activation Button (17) to secure the screen.
  7. Use separating rods to carefully pull left and right, applying appropriate pulling motion to separate the screen. Repeat as needed.
  8. After operation, turn OFF the suction button and power switch. Disconnect power and clean the plate once cooled.
LCD Screen Separator in operation with temperature and suction details

Figure 3: LCD Screen Separator features, showing temperature range (50-120°C), adjustable temperature, suction pad & pump, PID temperature stabilization, and a USB charging port.

Compatible devices for LCD separator and suction hole note

Figure 4: Compatible devices (smartphones & watches) for the LCD separator. Note: Cover selective suction holes with the silicone pad provided before removing glass from the LCD.

6.2. Hot Air Rework Station

  1. Place the hot air gun in its holder (20).
  2. Turn ON the main power switch (19), then turn ON the Hot Air Rework Station power switch (11).
  3. Use the Temperature Adjustment Knob (12) to select the desired temperature and the Air Volume Adjustment Knob (10) for air output.
  4. The station will begin heating. The operation indicator (dot at bottom-right of display) turns ON when heating, blinks rapidly when stable, and turns OFF when cooling.
  5. Once stable, the hot air gun is in high precision thermostatic state.
  6. After operation, turn OFF the Hot Air Rework Station power button. The heating will cut off, and the gun will cool down. Once below 100°C (212°F), the display turns OFF.
Hot Air Gun features diagram

Figure 5: Hot Air Gun features, including extremely low noise (45dB), air volume (≤120L/min), rotating wind tunnel for steady temperature, and smart warming for precise output. Warning: Do not touch the nozzle when in use.

6.3. Soldering Station

  1. Connect the soldering iron to the receptacle (16) and place it in its holder.
  2. Turn ON the main power switch (19), then turn ON the Soldering Station power switch (14).
  3. The soldering iron will begin heating. The operation indicator (dot at bottom-right of display) turns ON when heating, blinks rapidly when stable, and turns OFF when cooling.
  4. CAUTION: For first use, set temperature to 250°C/482°F. Once hot enough to melt solder, coat the tip with solder (rosin core recommended), then set to desired value.
  5. After operation, clean the tip with a wet sponge or metal wool ball, tin it with a new layer of solder, then return it to the holder. Turn OFF the power switch.
Soldering Station in operation with sleep mode details

Figure 6: Soldering Station features, showing temperature range (200-480°C), adjustable temperature, PID temperature stabilization, and sleep mode. Sleep mode idles at 200°C after 10 minutes of inactivity to reduce wear, heating up quickly when reactivated.

7. Function Configuration

7.1. Sleep Mode

The sleep mode automatically detects inactivity. If the soldering iron is not used for approximately 10 minutes, it enters sleep mode to prevent tip oxidation and prolong lifespan.

  1. To activate/deactivate: Press and hold the suction activation button (17) for ~5 seconds. The display will show "SLP 10" (10-minute countdown).
  2. Press the soldering station's power switch (14) to toggle the sleep mode function ON/OFF.
  3. Press the suction activation button (17) twice to exit the setting interface.
  4. To wake the soldering iron from sleep mode: Shake the soldering iron handle a few times, or turn OFF then ON the soldering station's power switch.

7.2. Buzzer Prompt

  1. To activate/deactivate: Press and hold the suction activation button (17) for ~5 seconds. The display will show "SLP 10".
  2. Press the suction activation button (17) again. The display will show "bEL ON" (buzzer ON) or "bEL OFF" (buzzer OFF).
  3. Press the soldering station's power switch (14) to toggle the buzzer ON/OFF.
  4. Press the suction activation button (17) once to exit the setting interface.

7.3. Fahrenheit/Celsius Conversion

This function allows you to switch between temperature units.

  1. With the station OFF, press and hold the suction activation button (17), then turn ON the main power switch (19). The display will show "C" or "F".
  2. Press the soldering station's power button (14) to switch between Fahrenheit and Celsius.
  3. Press the suction activation button (17) once to exit the setting interface.

7.4. Digital Temperature Calibration

Temperature discrepancies can occur. This function helps correct them and extends tool lifespan.

  1. Set the temperature value that requires calibration (e.g., 80°C/176°F for screen separator, 300°C/572°F for hot air rework/soldering station).
  2. Once the temperature is stabilized, press and hold the respective power button (Screen Separator (8), Hot Air Rework (11), or Soldering Station (14)) for approximately 8 seconds. The display will show 3 dots and the set temperature.
  3. Turn the respective temperature adjustment knob to enter the measured temperature.
  4. After the temperature reaches the calibrated temperature, press the respective power button to confirm. The system will save the calibration and exit.

7.5. Automatic Shut-down

If the soldering station is not woken from sleep mode within approximately 30 minutes, it will automatically shut off. To restart, turn OFF and then ON the main power switch (19). This function is only active when sleep mode is ON.

8. Maintenance & Precautions

8.1. General Precautions

  • Always disconnect the power cord before cleaning or performing maintenance.
  • Ensure the unit is completely cooled before handling components like nozzles or soldering tips.
  • Do not expose the unit to moisture or operate in wet conditions.

8.2. Screen Separator Maintenance

  • Do not knock the aluminum heating plate with hard objects.
  • Keep the aluminum heating plate clean. Prevent foreign objects from falling into the vacuum pump holes, as this can negatively impact suction performance.
  • CAUTION: The screen separator is not suitable for use in environments with excessive air turbulence, which can lead to insufficient temperature.

8.3. Hot Air Rework Station Maintenance

  • Keep the air outlet clear and free of blockages.
  • Install hot air nozzles ONLY when the steel pipe and nozzle have cooled. Install correctly without brute force; do not pull the edge with tweezers or over-tighten.
  • Select appropriate nozzles. For smaller nozzles, use maximum air volume with a lower temperature setting for the shortest duration to avoid damaging the hot air gun.
  • Maintain a minimum distance of 2mm between the object and the hot air gun's air outlet.
  • Do not allow hot air to contact facial parts; beware of burn injuries. Initial use may emit white fumes, which will dissipate shortly.
  • NOTE: The hot air gun and soldering iron handles use high-strength stainless steel tubes. A slightly bronzed steel tube is normal due to quality control and testing.

8.4. Soldering Station Maintenance

  • If an oxidation layer forms on the soldering iron tip, clean it with a metal wool ball. First, set the temperature to 300°C (572°F). Once stable, gently rub the tip inside the metal wool ball. When oxidation is partially removed, apply solder onto the tip while rubbing until it adheres completely. If severely oxidized, replace the tip.
  • Do NOT use metal files to remove oxidation from the tip. Replace deformed or rusted tips.
  • Do NOT apply excessive force when soldering, as this damages the tip and does not improve heat transfer.
  • When idling after high-temperature operation, adjust the temperature to 250°C (482°F) or below. Idling at high temperatures accelerates aging of the heating element and shortens tip lifespan.
  • Always clean and tin the soldering iron tip with solder after every operation to prevent oxidation.

9. Troubleshooting

  • "S-E" Error: Indicates a faulty sensor module or disconnected soldering iron. Turn OFF the station, re-connect the soldering iron, and reboot. If the issue persists, replace the heating element (which includes the sensor modules).
  • Heating Element Replacement: When replacing, note the original connecting order and colors of the wires; they MUST NOT be connected incorrectly.
  • "F-1" or "F-2" Error: Indicates activation of hot air fail-safe measures. Check the hot air gun and its power circuitry.
  • "SLP" Indication: The soldering station is in sleep mode.

10. Compatible Parts

10.1. Soldering Tip Styles

The YIHUA 853AAA-I is compatible with 902 Series soldering tips, with an outer diameter of 6.5mm. Various tip styles are available for different soldering tasks, including conical, chisel, and knife tips.

Diagram of various 902 Series soldering tip styles

Figure 7: Examples of 902 Series soldering tip styles (e.g., 902-B, 902-3.2D, 902-KI, 902-30).

10.2. Hot Air Nozzle Styles

A variety of nozzle styles are available for the hot air rework station, corresponding to different IC sizes and applications such as QFP, SOP, PLCC, SOJ, and BGA/CSP components. These nozzles ensure precise heat application for various rework tasks.

Diagram of various hot air nozzle styles and sizes

Figure 8: Examples of hot air nozzle styles and their corresponding IC sizes (e.g., QFP 10x10, PLCC 20x20, SOP 11x21).

11. User Tips

  • For optimal performance and longevity, always ensure proper grounding of the unit.
  • When working with the screen separator, use a heat-resistant mat to protect your workbench.
  • Regularly check and clean the air filter of the hot air rework station to maintain consistent airflow.
  • Keep a variety of soldering tips and hot air nozzles on hand to suit different project requirements.
  • Always use appropriate personal protective equipment (PPE), such as safety glasses and heat-resistant gloves, when operating the station.

12. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official YIHUA website or contact your authorized dealer. Keep your purchase receipt as proof of purchase for any warranty claims.

A detailed user manual in PDF format is available for download: YIHUA 853AAA-I User Manual (PDF)

13. Product Overview Video

Video: A visual demonstration of the YIHUA 853AAA-I multi-station's features and operation.

© 2024 YIHUA. All rights reserved. Product specifications are subject to change without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.