1. Product Overview
The motorcycle ABS (Anti-lock Braking System) sensor is a core detection component of the motorcycle's anti-lock braking system, mainly installed on the front and rear wheel hubs of the motorcycle. It is responsible for real-time detecting the rotational speed of the motorcycle's wheels, converting the mechanical speed signal into an electrical signal, and transmitting it to the ABS control unit. The ABS control unit uses this signal to monitor the wheel speed in real time; when the wheel is about to lock during braking, the control unit will adjust the brake pressure in time to prevent wheel lock, avoid side slip and loss of control, and effectively improve the braking safety of the motorcycle under various road conditions (especially wet and slippery roads). This product is specially designed for motorcycles, with compact structure, strong environmental adaptability and high detection accuracy, compatible with most mainstream motorcycle models (including street cars, locomotives, scooters and off-road motorcycles).
2. Main Features
- High detection accuracy, fast response speed: Signal delay less than 2ms, ensuring the ABS control unit obtains real-time and accurate wheel speed data for timely braking adjustment.
- Strong anti-interference ability: Effectively resists electromagnetic interference from the motorcycle's electrical system and external environment, ensuring stable signal output even in complex riding conditions.
- IP67 waterproof and dustproof performance: Adapting to harsh riding environments such as rain, dust, mud and road debris, preventing water and dust from entering the sensor and causing damage.
- High temperature and vibration resistance: Able to work stably under high-temperature environment (up to 150°C) and strong vibration during motorcycle riding, with good structural stability.
- Compact and lightweight design: Easy to install and match with various motorcycle wheel hub structures, adopting high-quality magnetic materials and precision manufacturing process, with long service life.
- Direct fit design: Compatible with most original motorcycle interfaces, no need to modify the vehicle structure, reducing installation difficulty.
3. Installation Instructions
3.1 Installation Preparation
Before installation, turn off the motorcycle's power supply and remove the ignition key to avoid electrical shock or component damage. Prepare the following necessary tools and perform checks:
- Tools: 8-10mm socket wrench, screwdriver, non-magnetic feeler gauge, compressed air, lint-free cloth, brake cleaner, Loctite 243 thread locker.
- Sensor Check: Verify the sensor model matches your motorcycle (front/rear wheel distinction). Inspect the sensor for damage, deformation, wire breakage, or missing parts.
- Installation Area Cleaning: Clean the installation position (wheel hub, sensor mounting bracket, and pulse ring) to remove dust, oil stains, metal shavings, and rust.
- Pulse Ring Check: Examine the pulse ring (toothed ring) for tooth damage, deformation, or rust. Replace if necessary.
3.2 Mounting Steps
- Locate and Align: Find the designated installation position (front or rear wheel hub). Align the sensor's mounting hole with the motorcycle's fixing bracket hole, ensuring the sensor probe is aligned with the pulse ring (toothed ring) on the wheel hub.
- O-ring/Gasket Installation: If equipped, install the O-ring or sealing gasket on the sensor's mounting end. Apply a small amount of engine oil or grease to ensure a good seal and facilitate installation. Verify the O-ring is undamaged and correctly positioned.
- Secure Sensor: Screw the sensor into the mounting bracket by hand first. Then, use a socket wrench to tighten the fixing bolt to the specified torque (usually 6-8 N-m, refer to your motorcycle's torque specification). Apply Loctite 243 thread locker if needed. Do not overtighten.
- Adjust Sensor Gap: Use a non-magnetic feeler gauge to measure the gap between the sensor tip and the pulse ring. The ideal gap is between 0.3 mm and 1.0 mm (max 1.85 mm for some models). If the gap is outside this range, use a thin shim or adjust the mounting bracket.
- Route Signal Wire: Route the sensor's signal wire along the motorcycle's frame and brake hose. Fix it with cable clips to prevent squeezing, wear, or entanglement with moving parts. Ensure sufficient slack to avoid pulling or breaking when the wheel turns.
- Connect Electrical Connector: Connect the sensor's electrical connector to the corresponding interface of the motorcycle's ABS control unit or wiring harness. Press the release tab until a distinct click is heard for a firm connection. Avoid pulling wires forcibly. Protect the connector from water and dust intrusion.
- Reinstall Parts: Reinstall removed parts (wheel, brake disc, fender). Double-check the sensor's installation and wire routing for any omissions or errors.
4. Post-installation Test and Operation Method
4.1 Post-installation Test
After installation, perform the following test to ensure proper function:
- ABS Indicator Light Check: Turn on the motorcycle's power. The ABS indicator light on the instrument panel should turn on and then go off shortly after the motorcycle starts moving (typically above 5 km/h), indicating normal sensor and ABS system operation.
- Brake Test: Ride at a low speed (20-30 km/h) and gently apply the brake. You should feel a slight vibration in the brake pedal if the ABS system activates. Observe if the wheel speed signal is stable on the instrument panel (if equipped).
- Signal Verification: Test brake performance at different speeds to confirm the sensor stably transmits wheel speed signals.
- Troubleshooting Abnormalities: If the ABS indicator light remains on, ABS does not activate, or the signal is unstable, stop immediately. Check installation gap, wiring, pulse ring, and sensor integrity.
- Learning Process (if required): Pinch the brake switch, turn on the ignition, repeat 8 times. Then ride to 50 km/h and slow down to stop until the ABS indicator light goes out.
4.2 Operation Method
- Automatic Activation: Start the motorcycle normally. The ABS sensor will automatically activate and begin detecting wheel speed, transmitting signals to the ABS control unit in real time.
- Braking Control: During riding, the ABS control unit monitors wheel speed. In emergency braking or on wet/slippery roads, if a wheel is about to lock, the control unit adjusts brake pressure (up to 20 times per second) to maintain wheel slip rate between 10% and 30%, ensuring directional control and optimal braking.
- Indicator Light Interpretation: If the ABS indicator light is off during riding, the system is normal. If it is on or blinking, it indicates a fault in the sensor or ABS system, and the ABS function may be invalid (conventional braking still works).
- Low Voltage Indication: A blinking ABS indicator light may signal low battery voltage. Turn off the ignition, charge the battery, and restart. If the fault persists, refer to the troubleshooting section.
- Automatic Shutdown: After the motorcycle stops and the power is turned off, the ABS sensor will stop working automatically. The ABS control unit records the last working data for maintenance reference.
5. Maintenance
- Daily Maintenance: After each use, wipe the sensor's surface and probe with a lint-free cloth. Check wiring and connectors for looseness, oxidation, damage, or water intrusion. Tighten, clean, or dry as needed. Check the pulse ring for dirt or damage.
- Regular Maintenance (Every 2000-3000 km or 3 months): Check and adjust the sensor's installation gap. Inspect the O-ring or sealing gasket for aging or damage and replace if necessary. Use compressed air to clean pulse ring slots. Check signal wire for wear or breakage.
- Long-term Storage: If the motorcycle is stored for a long time, disconnect the sensor's electrical connector, clean the sensor and installation position, and store the motorcycle in a dry, cool, dust-free environment. Store the sensor in multi-layer anti-static packaging.
- Professional Inspection (Every 10000 km): Have professional technicians inspect the sensor's performance and internal circuit. Use an oscilloscope to detect the signal waveform (normal waveform is a continuous sine wave). Replace the sensor if any potential fault is found.
6. Troubleshooting
- ABS indicator light remains on after startup:
- Check for loose, disconnected, or short-circuited sensor wiring.
- Check if the sensor's probe is blocked by dust, oil, or metal shavings.
- Check if the sensor is damaged (measure resistance between pins; normal range for two-wire sensors is 800-2300Ω).
- Check if the pulse ring (toothed ring) is worn, deformed, rusted, or has missing teeth.
- Check if the installation gap is within the specified range.
- No ABS activation during braking:
- Check for broken or poorly connected sensor signal wire.
- Check if the ABS control unit is faulty.
- Check if brake system pressure is normal.
- Check if the sensor's probe is misaligned with the pulse ring.
- Unstable ABS operation (abnormal brake pedal vibration):
- Check if the sensor's installation gap is too large or too small.
- Check if the pulse ring is dirty or damaged.
- Check if the sensor's internal electronic circuit is faulty.
- Check if wiring is interfered by external factors.
- Sensor fault code displayed (e.g., DTC 1-1, 1-2 for front wheel sensor abnormality): Use an OBD diagnostic tool to read the fault code. Check the corresponding circuit and sensor. Verify proper installation and connection. Erase the fault code and test-ride.
- Sensor damage (no resistance, short circuit, or open circuit): Replace with a new sensor of the same model. Re-adjust installation gap and wiring. Perform a post-installation test. Replace the pulse ring if damaged to prevent secondary damage.
7. Specifications
| Attribute | Value |
|---|---|
| Item Name | ABS Speed Sensor |
| Brand Name | HM TECH |
| Model Number (OE) | 10.0711-6260.3 (B000526) |
| Type | Speed Sensor |
| Origin | Mainland China |
| Item Weight | 0.1 kg |
| Applicable Models | BMW R nineT / BMW R1200GS 1200R Air/Oil Cooled GS 07-12 Motorcycle |
| Waterproof/Dustproof Rating | IP67 |
| Operating Temperature Range | -40°C to 150°C |
| Signal Delay | Less than 2ms |
| Normal Resistance (Two-wire sensors) | 800-2300Ω |
8. User Tips
No specific user tips were available from provided reviews or Q&A content. Always ensure the sensor is clean and properly gapped for optimal performance.
9. Warranty and Support
This product is covered by standard warranty terms. For detailed information regarding warranty claims or technical support, please contact our customer service team.
- Fast Delivery & Refunds: We offer fast delivery and provide refunds for delayed packages, lost packages, or damaged items.
- Security & Privacy: We do not share your personal details with third parties without your consent and protect your privacy.
An official user manual in PDF format is also available for download. Please refer to the product page for the direct link.