I. Warning & Safety Information
- Sharp Edges: Always wear protective gloves when installing or replacing wiper blades to prevent injury.
- Dry Operation: Do not operate wiper blades at high speed on dry glass surfaces, as this can cause damage to the wiper blades and the windshield.
- Handle with Care: Do not pull the wiper arm directly with your hands, as this can cause breakage or damage to the wiper mechanism.
II. Product Overview
This set includes front and rear windshield wiper blades designed specifically for Renault Scenic 3 and Grand Scenic 3 models manufactured between 2009 and 2016. The blades are made from high-grade natural rubber and feature a special vehicle interface for a perfect fit.

Figure 1: VENDY Wiper Blades installed on a Renault Scenic 3.
III. Setup (Installation)
Ensure your vehicle is parked safely with the engine off before beginning installation. This product is only suitable for left-hand drive vehicles.
- Prepare the Windshield: Clean the windshield thoroughly to remove any dirt or debris.
- Lift Wiper Arm: Gently lift the existing wiper arm away from the windshield until it locks into an upright position. Place a soft cloth or towel on the windshield to prevent damage if the arm accidentally springs back.
- Remove Old Blade: Carefully detach the old wiper blade from the wiper arm. This usually involves pressing a small tab or button and sliding the blade off.
- Install New Blade: Align the mounting clip of the new VENDY wiper blade with the hook or pin on the wiper arm. Gently press the blade into place until you hear a click, indicating it is securely fastened.
- Lower Wiper Arm: Carefully lower the wiper arm back onto the windshield.
- Test Operation: After installation, spray water on the windshield and operate the wipers to ensure they function correctly and provide a clear, streak-free wipe.

Figure 2: Visual guide for various wiper blade installation types. Ensure your specific arm type matches the corresponding installation method.
Video 1: Demonstration of wiper blade installation and operation.
IV. Operating Instructions
Your VENDY wiper blades are designed for high cleaning efficiency, effectively removing rainwater and dirt for clear visibility.
- Normal Operation: Use your wipers as needed during rain, snow, or when the windshield is dirty.
- Ice Formation: If ice forms on the windshield or wiper blades after use, ensure you remove the ice layer completely before operating the wipers. Do not force the wipers through ice.

Figure 3: Comparison showing the clear wipe of VENDY wipers versus the blurred vision from other wipers.

Figure 4: Demonstrates clearly visible driving conditions with VENDY wipers compared to vague visibility.
V. Maintenance
- Replacement Interval: It is recommended to replace your wiper blades every 6-12 months, or immediately if you notice wiper blade skipping, abnormal noise, or streaking.
- Cleaning: To clean the wiper blades, wipe the rubber strip with a soft cloth dampened with a neutral detergent. Do not use gasoline, alcohol, or corrosive cleaning agents, as these can damage the rubber.
- Storage: When not in use for extended periods, store the wiper blades in a cool, dry place, away from direct sunlight and high-temperature environments (above 70°C). Covering them with a protective sleeve can also extend their lifespan.
- Compatibility: Wiper blades are designed for glass surfaces and are not suitable for non-glass applications. When replacing, always select the original equipment manufacturer (OEM) specification and model for optimal performance.
VI. Troubleshooting
- Wiper Skipping: If your wiper blades are skipping across the windshield, this may be caused by aging of the rubber strip or an oily film on the glass. Clean the windshield and blades thoroughly. If the issue persists, consider replacing the blades.
- Excessive Noise: If your wipers are making excessive noise, check for any foreign objects trapped under the blade or inspect the rubber strip for deformation. Ensure the wiper arm is not bent and the blade is properly seated.
- Poor Wiping Performance: If the wipers are leaving streaks or not clearing the windshield effectively, the rubber may be worn or damaged. Clean the blades and windshield, and if the problem continues, replace the wiper blades.
VII. Specifications
| Product Name | Upgraded Intelligent Boneless Windshield Wiper Blades |
| Brand | VENDY |
| Placement | Front & Rear Windshield |
| Material | High-Grade Natural Rubber, Memory Steel Sheet, Double Carbon Steel Bar |
| Temperature Tolerance | +158℉ to -40℉ (-40℃ to +70℃) |
| Lifespan | 1 Million Times of Wiping |
| Front Wiper Sizes | 30 inches (750mm), 26 inches (650mm) |
| Rear Wiper Size | 12 inches (300mm) |
| Item Weight | 0.35 kg (approx.) |
| Package Dimensions | 53 cm (L) x 28 cm (W) x 7 cm (H) |

Figure 5: Detailed product parameters including temperature tolerance and lifespan.
VIII. User Tips
- Regular Inspection: Periodically check your wiper blades for any signs of wear, cracks, or damage to the rubber. Worn blades can snap or detach unexpectedly.
- Secure Installation: Always ensure the wiper blades are securely clicked into their mounting clips. A loose blade can detach during operation, potentially causing damage to your windshield.
- Clean Windshield: A clean windshield free of oily films or debris will significantly improve wiper performance and reduce noise.
IX. Warranty & Support
For any product-related inquiries, technical support, or warranty claims, please contact your original seller or retailer. This product complies with CE marking requirements, indicating conformity with relevant EU directives for safety and hygiene.
CE Marking Information:
The CE marking is a mandatory requirement for products entering the European market, indicating compliance with the essential requirements of relevant EU directives, such as safety, hygiene, and environmental protection.