Godox MF-T76

Contents

Godox MF-T76 TTL Macro Twin Flash Instruction Manual

Model: MF-T76

Brand: Godox

Foreword

Thank you for purchasing a Godox product! The MF-T76 is a TTL Macro Twin Flash with adjustable angles, suitable for macro photography subjects such as insects, plants, jewelry, and dental work.

  • MF-T76 C: For Canon cameras
  • MF-T76 S: For Sony cameras
  • MF-T76 N: For Nikon cameras

Note: The product images and interface displays in this manual are based on the MF-T76 C.

Key Features

  • Dual Flash Units: Independent settings for both flash tubes. Flash angles are adjustable using the included mounting ring.
  • 2.4G Wireless X System: Supports switching between Transmitter and Receiver modes.
  • Precise Light Control: Power range from 1/256 to 1/1 in 1/3 increments.
  • Outstanding Performance: Approximately 550 full power flashes on a full charge.
  • Built-in Modeling Lamp: Brightness adjustable from 1 to 10 levels.
Godox MF-T76 Macro Twin Flash with key features highlighted: Dual Flash Heads, TTL Auto Flash, Independent Flash Unit, Flexible Tilt Angles, 1.2s Full-power Recycling.

Figure 1: Key Features of the MF-T76 Macro Twin Flash

What's Inside (Package Contents)

The package includes the following items:

Contents of the Godox MF-T76 package including flash body, adapter, lithium battery, USB-C to USB-A cable, diffusers, adapter ring, adapter rings kit, storage bag, and instruction manual.

Figure 2: Package Contents

  • Flash Body ×1
  • Adapter ×1
  • Lithium Battery ×1
  • USB-C to USB-A Cable ×1
  • Diffuser ×2
  • Adapter Ring ×1
  • Adapter Rings Kit AR-R (49mm, 52mm, 55mm, 58mm, 62mm, 67mm, 72mm, 77mm) ×1
  • Storage Bag ×1
  • Instruction Manual ×1

Names of Parts

Controller

Diagram of the Godox MF-T76 controller unit with numbered parts: Display, MODE button, Modeling Lamp button, MENU/LOCK button, RATIO button, SET button, Test button/Recycle Indicator, Select Dial, Power Switch button, Hot Shoe Locking Ring, Hot Shoe, Battery Charging Indicator, USB Charging Port, 2.5mm Sync Cord Jack, USB Upgrading Port, Battery Release Button, Lithium Battery.

Figure 3: Controller Unit Overview

  1. Display
  2. <MODE> Button
  3. < > Modeling Lamp Button
  4. <MENU/> MENU/LOCK Button (Press and hold at the same time to reset)
  5. <RATIO> Button
  6. <SET> Settings Button
  7. Test Button / Recycle Indicator (Green: Ready / Red: Recycling)
  8. Select Dial
  9. Power Switch Button
  10. Hot Shoe Locking Ring
  11. Hot Shoe
  12. Battery Charging Indicator (Green: Fully Charged / Red: Charging)
  13. USB Charging Port
  14. 2.5mm Sync Cord Jack
  15. USB Upgrading Port
  16. Battery Release Button
  17. Lithium Battery

Flash Head

Diagram of the Godox MF-T76 flash heads with numbered parts: Flash Head A, Flash Head B, Flash Head Release Button, Installing Slot, Indicator Arrow, Modeling Lamp A, Modeling Lamp B.

Figure 4: Flash Head Overview

  1. Flash Head A
  2. Flash Head B
  3. Flash Head Release Button
  4. Installing Slot
  5. Indicator Arrow
  6. Modeling Lamp A
  7. Modeling Lamp B

Adapter Ring

Diagram of the Godox MF-T76 adapter ring with numbered parts: Detaching Mount, Installing Spot/Indicator Arrow, Adapter Ring Connecting Port.

Figure 5: Adapter Ring Overview

  1. Detaching Mount
  2. Installing Spot/Indicator Arrow
  3. Adapter Ring Connecting Port

Setup and Installation

1. Battery Installation and Removal

Installation: Insert the battery into the battery compartment in the correct orientation as shown until it locks into place.

Image showing the battery being inserted into the controller unit.

Figure 6: Battery Installation

Removal: Press and hold the Battery Release Button, and slide the battery to the right to remove it.

2. Controller Installation and Removal

Installation: Turn the Hot Shoe Locking Ring counter-clockwise to the top. Slide the hot shoe into the camera hot shoe, then turn the ring clockwise to lock.

Image showing the controller unit being mounted onto a camera hot shoe.

Figure 7: Controller Installation

Removal: Press and hold the release button on the locking ring, turn the ring counter-clockwise to unlock, and remove the controller.

3. Flash Head Installation and Removal

Installation:

  1. Install the included lens adapter ring onto the camera lens.
  2. Hold the Mounting Position on the mounting ring. Insert the flash head in the correct orientation until it clicks into place.
  3. Press and hold the release buttons on both sides of the flash head to adjust its position.
  4. Align the mounting ring connector with the adapter ring, insert it vertically, and lock it into place.
Image showing the flash heads being mounted onto a camera lens via the adapter ring, demonstrating flexible tilt angles.

Figure 8: Flash Head Installation on Lens

Removal:

  1. Position the flash head at the mounting location and pull outward to detach.
  2. Pull the mounting ring outward to release the locking mechanism, then slide it upward to remove.

4. Diffuser Installation

Align the short bayonet mount with the upper slot on the flash head and the long bayonet mount with the lower slot. Push until it locks securely into place.

Image showing the installation of diffusers on the flash heads and the effect on lighting a beetle, with and without diffusers.

Figure 9: Diffuser Installation and Effect

Operating Modes

Power Switch

  • Power On: Slide the switch to the ON position.
  • Power Off: Slide the switch to the OFF position.

Flash Mode

Short press the < MODE > button to switch between TTL / M mode.

TTL Auto Flash

The flash unit works with the camera's metering system to automatically adjust optimal flash output. This mode triggers a pre-flash before the shutter releases, allowing the flash to receive camera data for the main flash.

Flash exposure compensation: Range -3.0 ~ +3.0, Step: 1/3

Four panels showing TTL and HSS modes, with example macro shots. Text: 'Fast, Intuitive Shooting with TTL and HSS', 'TTL Auto Flash', 'HSS Mode', 'TTL Mode'.

Figure 10: TTL and HSS Modes in Action

1. Set Overall Exposure Compensation
Short press the < RATIO > button to make "A+B" icon on the display. Turn the select dial to set exposure compensation.

2. A:B Flash Ratio Setting
Short press the < RATIO > button until "A: B" is displayed on the screen. Turn the Select Dial to set the flash ratio. (Range: 8:1-1:1-1:8, Step: 1/2). Short press the < SET > button and turn the select dial to set the exposure compensation.

3. Set Individual Flash Exposure Compensation
Short press the < RATIO > button until "A" and "B" are displayed. Press the < SET > Button to switch between flash tube A and B, then turn the Select Dial to set the Flash Exposure Compensation.

M Manual Flash

Manually set the flash output. Range: 1/256 - 1/1, Step: 1/3

Diagram showing independent power adjustment for left and right flash heads, with settings 1/32 for both. Text: 'Control Light Shape Depth', 'Left 1/32', 'Right 1/32'.

Figure 11: Independent Power Control for Flash Heads

1. Overall Flash Ratio Setting
Short press the RATIO button until "A+B" is displayed. Turn the Select Dial to set the Flash.

2. A:B Flash Output Setting
Short press the RATIO button until "A" and "B" are displayed with individual power values. Press the <SET> Button to switch between flash tube A and B, then turn the Select Dial to set the Flash.

3. Single Group Flash Output Setting
Short press the RATIO button to make "A" and "B" icon and single group output value on the display. Press the < SET > Button to switch between flash tube A and B, then turn the Select Dial to set the Flash.

Operation Mode (Wireless)

To enter the wireless operation mode menu:

  1. Short press the < MENU/ > button to enter the menu.
  2. Turn the Select Dial to select "WIRELESS", then press the < SET > Button to enter.
  3. Turn the Select Dial to cycle through OFF / TX / RX, then press the <SET> Button to confirm.
  4. Press the < MENU/ > Button to exit.

TX Transmitter Mode

Wirelessly controls other Godox X system flashes.

Turn the Select Dial to select a group, then press the < SET > Button to enter. Press the <MODE> Button to switch among TTL / M / -- (OFF). Turn the Select Dial to Flash Exposure Compensation or power output.

Transmitter Groups:

  • Groups A, B, C, D (MF-T76 C)
  • Groups M, A, B, C (MF-T76 S/N)

RX Receiver Mode

Receives wireless trigger signals as a receiver unit. Press the < SET > Button or turn the Select Dial to switch groups.

Receiver Groups:

  • Groups A, B, C, D (MF-T76 C)
  • Groups A, B, C (MF-T76 S/N)

Other Function Settings

Modeling Lamp

The MF-T76 features built-in modeling lights for easier focusing and previewing light direction.

Image showing the flash heads with modeling lights on, illuminating a subject for easier focusing.

Figure 12: Built-In Modeling Lights

To adjust the modeling lamp:

  1. Long press the < > button to enter settings.
  2. Short press the < SET > button to switch between Modeling Lamp A and B.
  3. Short press the < > button to turn the lamp on or off.
  4. When turned on, rotate the select dial to adjust brightness (Range: 01-10).
  5. Long press the < > button to return to the main interface.

Quick Control in Main Interface:

  • Short press once: Turn Modeling Lamp A on/off.
  • Short press twice: Turn Modeling Lamp B on/off.

Locking Function

Long press the < MENU/ > button to lock or unlock the display. Note: Long press the < MENU/ > button won't work in menu interface means it's not locked.

Sync Cord Jack Triggering

The sync cord can be inserted into the 2.5mm sync port to fire the flash.

Factory Reset

Long press the < > button and the < MENU/ > button until "RESET" icon appears on the display, the icon disappears means resetting is completed.

Wireless Multi-Flash Photography (2.4G Wireless Transmission)

This section describes how to use the MF-T76 as a transmitter for wireless multi-flash photography when paired with flashes featuring 2.4G wireless receiving functions (sold separately).

Compatible models include: Outdoor Flashes: AD100ProII, AD200ProII, AD600ProII, AD600BMII, etc; On-camera Flashes: MF-T76, iT32, iT30Pro, V100, V480, etc; Retro Flashes: LUX Master, etc.

In this chapter, the MF-T76 mounted on the camera is referred to as the "Transmitter," and the controlled flashes are referred to as "Receivers."

Image showing the Godox MF-T76 integrated into a multi-flash setup with other Godox X System flashes, demonstrating seamless wireless integration.

Figure 13: Seamless Wireless Integration with Godox X System

Note:

  1. Ensure the transmitter and receivers are set to the same channel, group, and wireless ID.
  2. The MF-T76 is compatible with various receiver models; those listed above are for reference only.
  3. The MF-T76 S transmitter does not support Group D.

TTL: Wireless Multiple Flash Shooting in TTL Auto Flash Output Mode

Set the transmitter groups (A, B, C, D) to TTL mode and adjust the exposure compensation. Receivers will fire automatically based on their assigned group settings.

M: Wireless Multiple Flash Shooting in M Manual Flash Output Mode

Set the transmitter groups (A, B, C, D) to M mode and adjust the power output. Receivers will fire automatically based on their assigned group settings.

Wireless Multiple Flash Shooting in Different Flash Modes

Set the transmitter groups (A, B, C, D) to different flash modes and adjust the exposure compensation or power output. Receivers will fire automatically based on their assigned group settings.

Note:

  1. When the camera is set to fully automatic mode or program image control area mode, the operations in this chapter cannot be achieved. The wireless flash shooting can be achieved when the camera is set to P/Tv/Av /M/B (creative shooting).
  2. Do not set obstacles between the transmitter and the receivers to avoid interference.
  3. Please conduct flash test and shooting test before wireless multiple flash shooting.

Troubleshooting

Please refer to the guide table below when problems occur.

ProblemsPossible ReasonsSolutions
Flash does not fireNot correctly installedPlease mount the hot shoe of the flash securely on the camera.
The electronic contacts of the flash and camera are dirtyClean the electronic contacts of the flash and camera.
Power down automaticallyThe power will automatically shut down over 90s of idle use when using as a transmitter unit and the STBY is on.Press any button to wake up
The power will automatically shut down over 60min or 30min of idle use when using as a receiver unit and the RX STBY is set as 60mins or 30mins.Press any button to wake up
Can not boot upBattery runs out or damagesPlease charge or replace the battery.
Flash does not fire as a receiver unitThe receiver's flash group is incorrect. For example, group B of the transmitter is off but the receiver is set as group B.Set the flash group of receiver correctly.
The channels of transmitter and receiver are inconsistent.Please set the channels of transmitter and receiver to the same, e.g., set the channel of transmitter to 01, and receiver's to 01 as well.
The receiver is out of the transmission distance of the transmitter.Please set the receiver within the transmission distance (0-100m) of the transmitter.
The transmitter and receiver are too close for transmission.Please set the triggering distance in MENU-RF DIST as 0.3m to 10m.

Over-Temperature Protection

To avoid overheating and deteriorating the flash head, do not fire more than 40 continuous flashes in fast succession at 1/1 full power, or fire more than 30 continuous flashes in fast succession at 1/1 full power in HSS mode.

If you fire multiple continuous flashes mentioned below in short intervals, the inner overtemperature protection function may be activated and < > is shown on the display. If this occurs, allow a rest time of about 10 minutes.

Number of flashes that will activate over-temperature protection:

Power Output LevelNumber of Flashes
1/1, 1/2+0.740
1/2+0.350
1/260
1/4+0.3, 1/4+0.7100
1/4120
1/8 (+0.3, +0.7)200
1/16 (+0.3, +0.7)300
1/32 (+0.3, +0.7)500
1/64 (+0.3, +0.7)1000
1/128 (+0.3, +0.7), 1/256 (+0.3, +0.7)2000

Number of flashes that will activate over-temperature protection in HSS mode:

Power Output LevelNumber of Flashes
1/130
1/2 (+0.3, +0.7)30
1/4 (+0.3, +0.7)34
1/8 (+0.3, +0.7)40
1/16 (+0.3, +0.7)50
1/32 (+0.3, +0.7)50

Other Protections

Prompts on the panelMeaning
E0A failure occurs on the temperature sensor inside the device, need to be repaired.
E1A failure occurs on the recycling system so that the flash cannot fire. Please restart the flash unit. If the problem still exists, please send this product to a maintenance center.
E2The system gets excessive heat. Please allow a rest time of 10 minutes.
E3The voltage on two outlets of the flash tube is too high. Please send this product to a maintenance center.

Compatible Camera Models

MF-T76 C (For Canon):

A type cameras: 80D, 90D, 7D, 6D, 70D, 750D, 760D, 5DMarkIV, EOS 1DX, 6DMarkII, 77D, 800D, 5DMarkIII, 5DMarkII, 60D, 7D Mark II, 200DII, 1500D, 3000D

B type cameras: 600D, 50D, 30D, 500D, Digital X

C type cameras: M5, M50, R, RP, R7

MF-T76 S (For Sony):

α77II, α99, α77, DSC-RX10, α6000, α7R, α350, α7RII(4.0), α7RIII, α7M3, α9, α7RIV, α7R5, α7MIV, ZV-E10, A9III, A7C, A7CII, α6400, α6500

MF-T76 N (For Nikon):

D800, D750, D700, D610, D500, D200, D300S, D5, D4, D810, D780, D5300, D5200, D5100, D5000, D3300, D3100, D60, Z6, Z7II, Z8, ZFC

Note:

  1. This table only lists the tested camera models. For the compatibility of other models, a self-test is recommended.
  2. A type cameras don't support 2.4G wireless second curtain sync, B type cameras don't support 2.4G wireless second curtain sync and Gr mode, C type cameras don't support 2.4G wireless second curtain sync and AF focus assist beam.
  3. Rights to modify this table are retained.

Firmware Upgrade

Visit the official Godox website at https://www.godox.com.cn/firmware-G3/ to download the Godox G3 software and the latest firmware file.

  • Connect: With the device powered off, connect it to a computer using the included USB-C cable.
  • Upgrade: Open the Godox G3 software, select the firmware file, and execute the upgrade.

Technical Data (Specifications)

Product NameMacro Twin Flash
ModelMF-T76 C/MF-T76 S/MF-T76 N
Flash Power (1/1 step)76Ws
Guide No. (1/1 step)Approx. GN22.4 (ISO100, in meters)
Flash Power Range1/1-1/256 (with ±1/3 increment)
FEB±3 step, with ±1/3 increment
Flash Duration (t0.1)1/700s~1/19300s
Number of Flashes (1/1 step)Approx. 550
Recycle Time (1/1 step)Approx. 1.2s
Flash ModeTTL Flash, M (Manual) Flash
Flash Head Angle0°~150°
Modeling Lamp Power1W×2
Modeling Lamp CCT4800K±300K
Wireless Transmission Distance0-100m
CH32 groups: 01-32
ID99:01-99
HSSYes
Second Curtain SyncYes
First Curtain SyncYes
Lithium Battery7.2V/2980mAh
Working Environment Temperature-10~50°C
Flash Head Dimension (excluding connecting cable)2.97"×3.21"×1.18"
Controller Dimension (excluding connecting cable)5.35"×2.78"×2.44"
Net Weight (excluding battery)≈466g

All specifications are based on Godox test standards. Designs and specifications are subject to change without notice.

Maintenance

  • Impact Protection: The device may malfunction if subjected to strong shocks or vibration.
  • Keep Dry: This product is not waterproof. Do not operate with wet hands or use in the rain, bathrooms, or other humid environments.
  • Temperature Precautions: Avoid sudden temperature changes, such as moving from a cold environment to a warm one, which may cause internal condensation. To prevent this, place the device in a protective bag beforehand to allow it to adjust to the temperature change.
  • Magnetic Interference: Keep away from strong electromagnetic field sources, such as radio transmitters, to prevent electromagnetic interference from affecting device performance.

User Tips

  • For optimal macro photography, experiment with different flash head angles and power ratios to achieve desired lighting effects.
  • Utilize the modeling lamps to preview your lighting setup before taking a shot, especially in low-light conditions.
  • When using the wireless X system, ensure all units (transmitter and receivers) are on the same channel, group, and ID to avoid misfires.
  • If experiencing interference with wireless triggering, try changing the channel (CH) setting on your flash trigger and turning off other 2.4G equipment nearby.

Warranty and Support

The warranty period for this device as a whole is one year. Consumables (such as batteries), adapters, power cords, and other accessories are not covered by the warranty. Unauthorized repairs will void the warranty and will incur charges.

How to Get Maintenance Service:
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact Godox after-sale service. When applying for maintenance service, you should provide a valid warranty card. If you cannot provide a valid warranty card, service may still be offered if the product or accessory is confirmed to be within the maintenance scope, but this is not an obligation.

Contact Information:
GODOX Photo Equipment Co., Ltd.
Add: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao'an District, Shenzhen 518103, China
Tel: +86-755-29609320 (8062)
Fax: +86-755-25723423
E-mail: godox@godox.com

PDF User Manual: For a detailed PDF version of the user manual, please refer to the official documentation available at this link.

Product Video

Watch this video for a quick overview of the Godox MF-T76 Macro Twin Flash, demonstrating its quick setup, TTL auto flash, built-in modeling lamp, dual flash units, flexible dual heads, and versatile accessories.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.