Toyota B-LOGO-TOYOTA-E001

Contents

LED Car Door Welcome Courtesy Projector Lights

Model: B-LOGO-TOYOTA-E001

Introduction

These LED Car Door Welcome Courtesy Projector Lights are designed to project a clear logo onto the ground when your car door is opened, providing both illumination and a stylish aesthetic. This manual provides detailed instructions for installation, operation, and maintenance.

Safety Information

Please read all instructions carefully before installation and use.

  • Ensure the vehicle's power supply is turned off before beginning installation to prevent electrical shock.
  • Handle electrical components with care.
  • Do not attempt to modify the product.
  • Keep out of reach of children.
  • If you are unsure about any step, seek professional assistance.

Package Contents

Your package should contain:

  • 2 x LED Car Door Welcome Projector Lights

Setup

Installation Guide

Follow these steps to install your LED Car Door Welcome Projector Lights:

  1. Prepare for Installation: Ensure your vehicle's power supply is turned off. Locate the existing door entry light at the inner bottom of your car door.
  2. Remove Original Light: Carefully use a pry tool (or a flat-head screwdriver wrapped in tape to prevent scratches) to gently wedge into the gap around the original door entry light. Pry out the original decorative trim and the light assembly. The original light is typically held by two small clips.
  3. Disconnect Original Light: Once the original light is removed, disconnect its electrical connector.
  4. Connect New Light: Take your new LED Welcome Projector Light. Connect its plug to the vehicle's existing electrical connector. Ensure the connection is secure.
  5. Test Functionality: Before fully securing the new light, briefly open the car door to check if the light turns on normally and the projected pattern is clear. If it doesn't light up or the pattern is unclear, check the connection and the orientation of the plug (some connectors can be inserted in two ways).
  6. Install New Light: Once tested and confirmed working, carefully insert the new LED Welcome Projector Light into the opening in the car door until it clicks securely into place.
  7. Final Check: Close and open the door a few times to ensure the light is stable and functioning correctly.
Installation Steps Diagram

Figure 1: Visual guide for the installation process.

Video 1: Demonstration of LED car door light installation.

Important Note: If your original car door does not have door lights or the door light function is missing, you may need to install an adapter cable for modification. Please confirm this requirement for your specific vehicle model before purchasing.

Operating

These LED Car Door Welcome Projector Lights operate automatically. When the car door is opened, the light will turn on and project the chosen logo onto the ground. When the door is closed, the light will turn off.

Maintenance

To ensure the longevity and clarity of your projector lights:

  • Clean the lens periodically with a soft, dry cloth to remove dust or smudges that might affect projection clarity.
  • Avoid using abrasive cleaners or solvents, as these can damage the lens or housing.
  • Ensure the lights are kept free from excessive moisture or direct water spray.

Troubleshooting

If you encounter issues with your LED Car Door Welcome Projector Lights, try the following:

  • Light Not Turning On:
    • Check the electrical connection to ensure it is secure and properly seated.
    • Verify that the vehicle's power supply is active (e.g., door is open).
    • Ensure the polarity is correct if the connector allows for reversible insertion.
  • Projection Unclear or Dim:
    • Clean the projector lens with a soft cloth.
    • Ensure the light is fully seated and correctly oriented in its housing.
    • Check for any obstructions in the projection path.
  • Light Flickers:
    • Check for loose electrical connections.
    • Ensure the voltage supply from the car is stable.

If problems persist, consult a professional automotive technician.

Specifications

Product Specifications

ParameterDetail
Product Name3D Laser Lamp Projector
Model NumberB-LOGO-TOYOTA-E001
Item TypeWelcome Light
MaterialABS + Aluminum
ChipCREE (Imported from USA)
Working VoltageDC 9V-30V (DC 12V-24V recommended)
Output Power5W
Working Temperature40°C to 70°C
Product SizeConsistent with original lamp dimensions
Weight82g/set
Packing Size95mm x 93mm x 37mm
Applicable ModelsToyota Land Cruiser (2003-2014), Prado (2004-2010), Sequoia (2010-2014), Reiz (2006-2014), Camry (2006-2016), Highlander (2009-2014), E'Z (2011-2012), Corolla (2007-2011), Prius (2006-2012), Previa (2006-2012), Tundra (2011), Alphard (2011-2014), Sienna (2011-2014)
Product Specifications Table

Figure 2: Detailed product specifications.

User Tips

  • Before installation, double-check the compatibility list to ensure these lights fit your specific vehicle model and year.
  • When prying out the old lights, use a plastic trim removal tool to avoid scratching your car's interior panels.
  • If the projected logo appears upside down, try rotating the light unit 180 degrees before fully securing it, if the design allows.

Warranty and Support

For warranty information or technical support, please refer to your purchase documentation or contact the seller directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.