Viladepot Smart Lock D6 User Manual

1. Introduction

The Viladepot Smart Lock D6 is an advanced door locking system offering multiple unlocking methods for enhanced security and convenience. This smart lock is designed for both indoor and outdoor use, featuring a waterproof rating of IP63. It integrates seamlessly with the Tuya Smart Life app for remote control and management.

Important Notes:

• This lock is equipped with mechanical keys for manual unlocking. Always keep these keys in a safe place and accessible for emergencies.
• The lock requires 4 x AAA Alkaline batteries (not included) for power.
• For optimal performance of the fingerprint scanner, ensure your fingers are clean and dry.

2. Specifications

3. What's in the Box

The product package includes the following items:

• Exterior Lever *1
• Interior Lever *1
• Adjustable latch *1
• Strike plate *1
• Latch holding plastic box *1
• Emergency Unlock Key *2
• Installation Hardware (screws, square bar, etc.)
• ID Card *2
• User Manual (PDF)

4. Setup and Installation

The Viladepot Smart Lock D6 is designed for easy installation, typically taking around 10 minutes. No extra drilling is required for standard door preparations.

4.1 Door Compatibility

The lock is compatible with door thicknesses between 35mm and 50mm (1-3/8" to 2"). It supports a 2-3/8" (60mm) or 2-3/4" (70mm) backset and a 2-1/8" (54mm) door hole. The handle direction is reversible for both left-handed and right-handed doors.

4.2 Installation Steps

Before starting, ensure the front and rear handles are covered with protective film. This film should only be removed after the installation is complete.

1. Install the Lock Body: Adjust the backset of the lock latch as needed, then fix it to the door with 2 self-tapping screws. If the striking plate does not match your door grooves, you may change the door hole or use the old latch directly.
2. Install the Front Panel Copper Column: Pull out the cable and straighten it. Thread the hollow square bar through the cable to the bottom of the front handle. Attach the 2 screw bolts to the front cover. Be careful not to damage the cable.
3. Install the Square Bar: Insert the square bar into the mechanism.
4. Remove the Rear Panel Baffle: Carefully remove the baffle from the rear panel.
5. Connect the Data Cable: Connect the cable to the interface of the rear PCB according to the diagram, ensuring the connections align with the red mark to prevent crooked pins.
6. Install the Spring and Rear Panel: Attach the spring to the rear handle to prevent the hollow square bar and drive shaft from disengaging. Inset the front handle into the door hole, ensuring the screw bolts and hollow square bar pass through the latch bolt. If the door is more than 1.5 inches (38mm) thick, a spring needs to be placed on the rear handle.
7. Secure and Power On: Screw on the screws, install 4 x AAA alkaline batteries (ensure they are high-quality to avoid performance issues), and then close the battery baffle.

Important Safety Note: Do not use the mechanical key to unlock the device until the installation is fully complete and the drive shaft is homed. Using the key prematurely can damage the drive shaft. The mechanical key should only be used as a last resort for unlocking.

Installation Video:

5. Operating Instructions

The Viladepot Smart Lock D6 offers multiple convenient ways to unlock your door.

5.1 Tuya App Settings

The smart lock can be controlled and managed via the Tuya Smart Life app. Download the app by scanning the QR code in the manual or searching for "Tuya Smart" in your app store.

1. Create Family: Open the app, click "Me" in the lower right corner, then select "Home Management" and "Create a home". Follow the prompts to set up your home and invite family members.
2. Add Device:
   1. Tap the "+" symbol in the upper-right corner of the app and select "Add Device".
   2. Approve requests to enable Bluetooth and location services.
   3. Wake up the device by pressing the "#" key on the lock.
   4. The app should automatically detect the device. Click on the device's icon to add it.

   Note: If the device is not found, ensure Bluetooth & Location are on, then fully restart the app. Only one phone can be connected to a device at a time. To switch connections, first remove the device from the original phone or reset the device to factory settings.

3. Add Fingerprint:
   1. In the app, navigate to the lock's settings and select "Add Fingerprint".
   2. You will be prompted to press your finger on the fingerprint sensor 6 times. Ensure the fingerprint reader is completely covered by your finger each time.
   3. It is recommended to enter fingerprints from multiple angles to increase recognition rate.
   4. After successful registration, you can name the fingerprint for identification.
4. Add Password:
   1. In the app, navigate to the lock's settings and select "Add Password".
   2. You can choose to generate a random password or set a fixed one. Make sure to record or memorize the password.
5. Add Card (Key Fob):
   1. In the app, navigate to the lock's settings and select "Add Card".
   2. Place the ID card (key fob) on the recognition area of the lock until it is added successfully.

5.2 Unlocking the Door

• Fingerprint: Place your registered finger on the sensor.
• Passcode: Enter your registered password on the keypad.
• Card: Tap your registered ID card (key fob) on the card reader area.
• Mechanical Key: Insert the emergency key into the keyhole and turn to unlock.
• App Control: Use the Tuya Smart Life app to remotely unlock the door.

5.3 Personalization

• Temporary Password: Generate time-limited passwords for guests or service providers through the app.
• Silent Mode: Enable or disable sound feedback from the lock via the app.
• Normal Open Mode: Set the lock to remain unlocked for a specified period.

6. Maintenance

6.1 Battery Management

The lock is powered by 4 x AAA alkaline batteries. We recommend replacing all batteries every 6 months to ensure consistent performance.

Low Battery Alert: The lock will provide low battery alerts when power is below 30%. It is highly recommended to replace the batteries promptly when this alert occurs.

Emergency Power: If the batteries completely die, you can use the USB-C emergency power port on the exterior handle to provide temporary power with a power bank. This allows you to unlock the door and replace the batteries.

DO NOT attempt to recharge the AAA batteries through the emergency power port; it is for temporary power only.

6.2 Cleaning

Regularly clean the fingerprint scanner to remove any built-up dust or oil, which can reduce its sensitivity and lead to failed entries.

7. Troubleshooting

7.1 Fingerprint Scanner Not Responding Well

If the fingerprint scanner is not consistently recognizing your fingerprint:

• Re-register Fingerprint: Try deleting and re-registering your fingerprint in the app. You can store the same fingerprint multiple times to improve accuracy.
• Clean Sensor: Ensure the fingerprint sensor is clean and free from dust, dirt, or oil.

7.2 Door Not Unlocking

If the door lock is not responding or unlocking:

• Check Battery: Verify that the batteries are not depleted. Use the emergency USB-C port if needed, and replace batteries immediately.
• Handle Level: Ensure the handle is level. If it hangs down, it can affect unlocking. Lift the handle to unlock and adjust it to be level.
• Cable Connection: Check if the internal data cable is properly connected and that the pins are not deformed.
• Mechanical Key: Use the mechanical key as an emergency backup.

7.3 App Connectivity Issues

If the app cannot find or connect to the device:

• Ensure Bluetooth and Location services are enabled on your smartphone.
• Fully restart the Tuya Smart Life app.
• If you are trying to connect with a new phone, first remove the device from the original phone or reset the device to factory settings.

8. User Tips

• For optimal performance, ensure the installation is done carefully, paying attention to cable connections and handle alignment.
• Regularly check battery levels and replace AAA batteries proactively to avoid being locked out.
• Keep your mechanical keys in a secure, easily accessible location outside the door for emergencies.

9. Warranty & Support

The Viladepot Smart Lock D6 comes with a 90-day limited warranty.

For any problems or support inquiries, please feel free to contact us:

Email: support@viladepot.com

We aim to respond to all inquiries within 12 business hours.