IKSLED Remote control motion function switch

Contents

IKSLED 12V Automatic PIR Motion Sensor Switch User Manual

Model: Remote Control Motion Function Switch

Product Overview

This product is a human body induction switch with remote control function, specifically designed for low-voltage LED lights. It supports automatic motion-activated lighting, delayed turn-off and remote-controlled constant-on mode, suitable for various DC 3.7-24V LED strips and lamps, widely used in wardrobes, corridors, storage rooms and other scenarios.

IKSLED PIR Motion Sensor Switch and Remote Control

Figure 1: PIR Motion Sensor Switch and Remote Control

Specifications

Working VoltageDC 3.7V-24V
Sensing MethodPassive Infrared (PIR) Motion Detection
Sensing DistanceUp to 3 meters
Detection Angle120 degrees
Delay Time30 seconds (automatic turn-off after person leaves)
Control ModeDual-mode control via remote ON/OFF
Installation Size (Opening)17.5 mm
Package Dimensions18 cm (L) x 15 cm (W) x 3 cm (H)
Package Weight0.065 kg
CertificationsCE, RoHS
PIR Sensor Switch with 17.5mm measurement

Figure 2: Sensor switch with 17.5mm installation size indicated

Setup and Installation

Safety Precautions

  • Always cut off the power supply before beginning any installation or wiring to prevent electric shock or equipment damage.
  • This device is designed for low-voltage DC 3.7V-24V LED loads only. Do not connect it directly to mains high voltage (e.g., 110V/220V AC) to avoid burning the device.

Installation Location

  • Install the induction switch in a well-ventilated, unobstructed position.
  • Avoid locations with direct strong light sources or heat sources (e.g., vents, heaters) blowing directly onto the sensor, as this can cause false triggering.

Wiring Instructions

Refer to the wiring diagram below for correct connections. Ensure all connections are secure and correct before applying power.

Wiring Diagram for PIR Motion Sensor Switch

Figure 3: Wiring Specifications Diagram

Diagram Description: The diagram shows a low voltage constant power adapter (AC 85-265V input, DC 3.7-24V output) connected to the PIR sensor switch. The sensor switch then connects to the LED lamps/load. The wires are color-coded: Red (V+) and Black (V-) for power input to the switch, and Red (LED+) and Yellow (LED-) for power output to the LED load.

  1. Power Supply Connection:
    • Connect the positive pole (V+) of your low-voltage power adapter (DC 3.7-24V output) to the red wire (V+) of the switch.
    • Connect the negative pole (V-) of your low-voltage power adapter to the black wire (V-) of the switch.
  2. Load Connection (LED Lamp/Strip):
    • Connect the positive pole (LED+) of your LED lamp/strip to the red LED+ wire of the switch.
    • Connect the negative pole (LED-) of your LED lamp/strip to the yellow LED- wire of the switch.
  3. Pre-Test Check: After completing all wiring, carefully confirm that there are no short circuits or reverse connections in the circuit before turning on the power for testing.

Remote Control Battery Installation

The remote control requires a battery (not included). Install the appropriate battery into the remote control. Ensure the remote control is free from strong obstructions to maintain a stable signal.

Remote control with note about battery not included

Figure 4: Remote control, note that battery is not included

Operating Instructions

The PIR Motion Sensor Switch offers two operating modes, easily switchable via the included remote control.

Remote control function explanation

Figure 5: Remote Control Functionality (PIR On/Off)

Description: The remote control has "ON" and "OFF" buttons. "ON" activates motion sensor mode (light on when motion detected, off 30 seconds after person leaves). "OFF" activates constant-on mode (light stays on, power off to turn off).

1. Motion Sensing Mode (PIR ON)

  • Activation: Press the "ON" button on the remote control. The switch will enter motion sensing mode.
  • Functionality: The LED light will automatically turn on when human activity is detected within the sensing range. It will automatically turn off approximately 30 seconds after the person leaves the sensing range.

2. Constant-On Mode (PIR OFF)

  • Activation: Press the "OFF" button on the remote control. The switch will enter constant-on mode.
  • Functionality: The LED light will remain on continuously. To turn off the light in this mode, you must cut off the power supply directly (e.g., via a main power switch).

Maintenance

  • Cleaning: To ensure optimal performance, periodically clean the sensor lens with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
  • Long-Term Storage: If the device will not be used for an extended period, it is recommended to cut off the power supply to prolong its service life.
  • Remote Control Battery: Replace the battery in the remote control as needed to ensure reliable operation.

Troubleshooting

ProblemPossible Cause / Solution
Light not turning on
  • Check if the power wiring is reversed or loose.
  • Confirm the output voltage of the power adapter is normal and within DC 3.7V-24V.
  • Check if the LED light circuit is short-circuited or damaged.
Insensitive sensing / False triggers
  • Check if the sensor head is blocked by any objects.
  • Adjust the installation position to ensure a clear line of sight for the sensor.
  • Avoid installing near heat sources or strong light sources that could interfere with the sensor.
  • Confirm there are no obstacles blocking the human signal within the sensing range.
Light does not stay on in Constant-On Mode
  • Check the battery level of the remote control and replace if necessary.
  • Confirm that pressing the "OFF" button on the remote control is effective in switching to Constant-On mode.
  • Check if the wiring is correct and there is no open circuit at the load end.

User Tips

  • Remote Control Button Functionality: Some users have reported that the "ON" and "OFF" buttons on the remote control may function in reverse (e.g., pressing "ON" turns the light off, and "OFF" turns it on). If you experience this, simply adapt your usage accordingly.
  • Sensing and Remote Range: The detection range of the PIR sensor and the effective range of the remote control may not be very far. This product is generally more suitable for indoor use in smaller areas such as bedrooms, kitchens, closets, lockers, and hallways, rather than large outdoor spaces.

Warranty and Support

This product comes with standard manufacturer support. For any warranty claims, technical assistance, or further inquiries, please contact your seller directly.

For customized consultation, you may contact via WhatsApp: +86 15289643001.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.