1. Product Overview
The WenQia RF 433 Mhz Wireless Remote Control Switch is a versatile relay receiver designed to control various AC and DC devices wirelessly. It supports multiple operating modes, making it suitable for applications such as lighting, garage doors, and home automation.


2. Specifications
2.1. Relay Receiver Board Parameters
| Parameter | Value |
|---|---|
| Working Voltage | AC 85V~250V OR TYPEC 5V |
| Quiescent Current | <5MA |
| Max Current | 10 Amp |
| Max Load | 2200W |
| RF Frequency | 433MHz |
| Pin Configuration | COM, NO, NC |
| Working Temperature | -30°C ~ +80°C |
| Receiving Sensitivity | >97dbm |
| Storage Remote Controls | Up to 25 pieces |
| Receiving Range | More than 50 meters (open space) |
| Remote Operating Modes | Momentary, Toggle, Latched, Delay |
| Material | Plastic |
| Certification | RoHS, EMC, CE |
| Warranty | 1 Year |


2.2. Transmitter (Remote Control) Parameters
| Parameter | Value |
|---|---|
| RF Frequency | 433MHz |
| Support Encoding | 1527 Learning code |
| Transmitting Range | More than 50 meters (open space) |
| Battery | 1pc * CR2032 (included) |


3. Setup and Wiring
Before operation, ensure the receiver is correctly wired to your device and power source. The receiver supports both AC 110V~250V and Type-C 5V power input.
3.1. General Wiring Diagram

3.2. Garage Door System Wiring

3.3. Transforming a Manual Switch to Remote-Controlled

4. Operating Modes and Pairing
The wireless receiver supports four main operating modes. Each mode requires a specific pairing procedure. Refer to the video demonstration for a visual guide.
4.1. Resetting the Receiver
To clear all paired remote controls and reset the receiver to its default state:
- Press the learning button on the receiver 8 times.
- The indicator light will flash, confirming the reset.
4.2. Momentary Mode
Performance: Press and hold a button on the remote, the relay turns ON. Release the button, the relay turns OFF.
Pairing:
- Press the learning button on the receiver 1 time.
- Wait for 1 second.
- Press the desired button (e.g., 'A') on the remote control 1 time. The indicator light will flash, confirming successful pairing.
4.3. Toggle Mode
Performance: Press a button on the remote, the relay turns ON. Press the same button again, the relay turns OFF.
Pairing:
- Press the learning button on the receiver 2 times.
- Wait for 1 second.
- Press the desired button (e.g., 'A') on the remote control 1 time. The indicator light will flash, confirming successful pairing.
4.4. Latched Mode
Performance: Press button 'A' on the remote, the relay turns ON. Press button 'B' on the remote, the relay turns OFF.
Pairing:
- Quickly press the learning button on the receiver 3 times.
- Wait for 1 second.
- Press button 'A' on the remote control 1 time.
- Wait for 2 seconds.
- Press button 'B' on the remote control 1 time. The indicator light will flash, confirming successful pairing.
4.5. Delay Mode
Performance: Press button 'A' on the remote, the relay turns ON. The relay will automatically turn OFF after a set delay (5, 10, 15, or 20 seconds).
Pairing:
- Press the learning button on the receiver 4, 5, 6, or 7 times depending on the desired delay:
- 4 times for 5-second delay
- 5 times for 10-second delay
- 6 times for 15-second delay
- 7 times for 20-second delay
- Wait for 1 second.
- Press button 'A' on the remote control 1 time. The indicator light will flash, confirming successful pairing.
5. Troubleshooting
- Remote control not responding after pairing: Ensure the remote control has at least two buttons if you intend to use Latched mode.
- Weak signal or short range: Slightly stretch the antenna on the receiver for better reception. Ensure there are no major obstructions between the remote and the receiver.
- Remote control not working: Replace the CR2032 battery in the remote control if its voltage is low.
- Receiver not responding after reset: After a full reset (8 presses of the learning button), all previous pairings are cleared. You must re-pair your remote controls according to the desired operating mode.
6. Maintenance
- Battery Replacement: The remote control uses a CR2032 battery. Replace it when the indicator light on the remote becomes dim or the control range decreases. Refer to the remote control components diagram for battery location.
- Antenna Care: For optimal performance, ensure the receiver's antenna is slightly stretched and not obstructed.
- Cleaning: Wipe the devices with a dry, soft cloth. Do not use harsh chemicals or liquids.
- Water Resistance: The remote control features a waterproof silicone design, offering protection against splashes and accidental drops into water. However, prolonged submersion is not recommended.
7. User Tips
- Optimal Range: For best results, ensure a clear line of sight between the remote and the receiver. Walls and other electronic devices can reduce the effective range.
- Power Options: Take advantage of the dual power input options (AC 110V~250V or Type-C 5V) for flexible installation in various environments.
- Mode Selection: Carefully choose the operating mode (Momentary, Toggle, Latched, or Delay) that best suits your application before pairing.
- Testing: Always test the functionality of the paired remote and receiver after installation and before final deployment.
8. Warranty and Support
This product comes with a 1-year warranty from the date of purchase.
For technical support or inquiries, please contact:
- WhatsApp: +86135 0227 8583 / +86 1587521 692
- Email: dieseniectronic@163.com
A detailed user manual in PDF format is also available for download. You can find it by searching for "Item guides & documents" on the product page or by scanning the QR code provided in the product images.