GGBEE COB LED Strip Light

Contents

GGBEE COB LED Strip Light Instruction Manual

Model: 12V/24V COB LED Strip Light

1. Introduction

Thank you for choosing the GGBEE COB LED Strip Light. This flexible LED tape light is designed for various indoor decorative lighting applications, offering high brightness, soft light, and no dark areas. It is available in 12V or 24V options and features 320 LEDs per meter for uniform illumination. This manual provides essential information for safe installation, operation, and maintenance of your LED strip light.

General view of the GGBEE COB LED strip light
General view of the GGBEE COB LED strip light.

2. Safety Information

  • Power Supply: This product is compatible with 12V/24V DC power supply only. Do not connect to AC mains power directly. Connecting to an incorrect voltage or AC power will damage the strip and may pose a safety hazard.
  • Indoor Use Only: This LED strip is designed for indoor use. Avoid exposure to water and direct sunlight.
  • Handling: Do not bend the LED strip in the chip area. Excessive force or sharp bends can damage the internal components.
  • Temperature: Keep the LED strip away from high temperatures to ensure optimal performance and longevity.
  • Disconnection: Always disconnect power before any installation, maintenance, or cleaning procedures.

3. Product Specifications

FeatureSpecification
Product NameCOB Soft Light Strip
Input VoltageDC12V / 24V
PCB Width8mm
LED Quantity320 LEDs/M
Cutting LengthEvery 50mm
Color Temperature OptionsWarm White (2700K), Natural White (4500K), Cool White (6000K)
Color Rendering Index (CRI)Ra > 90
Beam Angle180°
Product Brightness900~1000LM/M
Operation Temperature-20℃ to +45℃
Storage Temperature-20℃ to +60℃
Luminous Flux<60
LED Chip ModelCOB
CertificationCE, ROHS
Power Consumption (approx.)12V: ~12W/m (1m), ~23W (5m)
24V: ~12W/m (1m), ~50W (10m)
Product parameters table for COB LED strip
Detailed product parameters.
Comparison of COB LED Strip vs SMD LED Strip
COB LED strips offer softer light without glare or vignetting compared to traditional SMD strips.

4. Package Contents

The package includes:

  • GGBEE COB LED Strip Light (with 2 wires and DC female connector)

Note: A power adapter is NOT included and must be purchased separately. Ensure the power adapter matches the voltage (12V or 24V) and wattage requirements of your LED strip length.

5. Installation

  1. Prepare Surface: Ensure the installation surface is flat, dry, and clean.
  2. Measure and Cut (if necessary): The LED strip can be freely cut at designated cut marks (typically every 50mm). Use sharp scissors to cut only along the marked lines. The rest of the LED strip will continue to function normally.
  3. Apply Adhesive: The LED strip features double-sided tape on its back. Peel off the protective backing and firmly press the strip onto the desired surface.
  4. Connect Wiring: Connect the wires from the LED strip to your matching DC power adapter. Ensure positive (red wire) and negative (black wire) terminals are aligned correctly.
Diagram showing dimensions, cuttable points, and double-sided tape
Dimensions, cuttable sections, and double-sided tape for easy installation.
Examples of COB LED strip light applications in a kitchen and ceiling
Example applications in kitchen and ceiling areas.

6. Operation

Once installed and connected to a suitable DC power adapter, the LED strip can be controlled via a power on/off switch. If your power adapter or an inline controller supports it, you can also adjust the brightness (dimmer adjustment).

Display of three available color temperatures and their light effects
Choose from Warm White (3000K), Natural White (4000K), or Cool White (6000K) to suit your ambiance.

7. Maintenance

  • Cleaning: Disconnect power before cleaning. Gently wipe the surface of the LED strip with a dry, soft cloth. Do not use harsh chemicals or abrasive materials.
  • Handling: Do not pull the wires or bend the LED strip forcefully during cleaning or repositioning.

8. Troubleshooting

  • LED Strip Does Not Light Up:
    • Check the power supply connection and ensure it is receiving power.
    • Verify that the positive and negative wiring connections are correct (red to positive, black to negative).
    • If the strip was cut, ensure the cut was made precisely at the designated cut position.
  • Only Part of the LED Strip is Lit:
    • Check the wiring connections along the strip for any loose or damaged points.
    • Inspect the cut positions if the strip was modified, as an improper cut can interrupt the circuit for subsequent sections.

9. User Tips

  • Power Supply Matching: Always ensure your power adapter's voltage (12V or 24V) matches your LED strip's requirements. Using an incorrect voltage can permanently damage the strip.
  • Wattage Calculation: Calculate the total wattage needed for your LED strip length (e.g., 12W/meter) and choose a power adapter with sufficient capacity to avoid overloading.
  • Surface Preparation: For best adhesion, thoroughly clean the surface with isopropyl alcohol and let it dry completely before applying the LED strip.
  • Even Light Distribution: For a seamless and even light effect, consider installing the COB LED strip within an aluminum profile with a diffuser.

10. Warranty and Support

For detailed warranty information and customer support, please refer to the seller's policies or contact the seller directly. A user manual in PDF format is available for download for further reference: View User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.