BAOFENG UV-5R Mini Dual Band Radio User Manual
Model: UV-5R Mini
Brand: BAOFENG
1. Introduction
Thank you for purchasing the BAOFENG UV-5R Mini Dual Band Radio. This easy-to-use radio features dual band, dual display, and dual watch capabilities, designed to provide secure, instant, and reliable communications with peak efficiency. Please read this manual carefully before use to ensure you derive maximum performance from your radio.
2. Safety Information and Regulatory Compliance
2.1 General Safety Warnings
WARNING! European Users: Operation of this unit in Transmit mode requires a valid Amateur Radio License from your respective Country's Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the "EU" specification guide 2014/53/EU.
ATTENTION! Programming: When programming the radio, always start by reading the factory software data. Then, rewrite this data with your desired frequencies and settings to a new saved code plug. Failure to do so may result in errors. Use a programming cable with a PC to program authorized frequencies, bandwidth, power, etc. Your programming must comply with your FCC (or EU/other country) license certification.
ATTENTION! RF Energy Exposure: Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.
PMR446, FRS, GMRS, MURS: While you may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies, please note that there are restrictions on these bands that may make this transceiver illegal for use.
2.2 Precautions for Portable Terminals
Operating Prohibitions:
- Do not operate the product in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials. Only approved Ex-protection models are allowed in such locations, and any attempt to assemble or disassemble is strictly prohibited.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where wireless communication equipment is completely prohibited.
Important Tips:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an airbag, do not place the product in the area over the airbag or in the airbag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation. Keep it in a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify, or repair the product and its accessories without authorization.
2.3 Precautions for Batteries
Charging Prohibitions:
- Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
- Do not charge a wet battery. Dry it with a soft and clean cloth prior to charging.
- Do not charge a battery suffering from deformation, leakage, or overheating.
- Do not charge with an unauthorized charger.
- Do not charge in a location where strong radiation is present.
- Overcharging is prohibited as it may shorten battery life.
2.4 Regulatory Compliance
EU Regulatory Conformance:
As certified by the qualified laboratory, this product complies with the essential requirements and other relevant provisions of Directive 1999/5/EC (2014/53/EU). All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU, 2012/19/EU). This information is applicable to EU countries only.
FCC Part 15 / IC Compliance:
This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
FCC RF Exposure:
It is the user's responsibility to properly operate this radio transmitter to ensure safe operation. Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Contact your local dealer for a replacement antenna.
Hand-Held Operation (Held-to-Face): This device was evaluated for typical hand-held (held-to-face) operations with a 1-inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face to comply with FCC RF exposure requirements.
Body-Worn Operation: This device was evaluated for body-worn operations with the supplied belt-clip accessory. All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines. Third-party accessories (unless approved by the manufacturer) should be avoided as they might not comply with FCC RF exposure guidelines.
3. Package Contents
The package typically includes the following items:
Image: Contents of the 2-pack BAOFENG UV-5R Mini radio kit.
Image: Detailed view of single radio package contents.
| Item | Quantity (PCS) | Item | Quantity (PCS) |
|---|---|---|---|
| Radio | 1 | Lanyard | 1 |
| Battery | 1 | Operation Manual | 1 |
| Antenna | 1 | Belt Clip | 1 |
*Charger and power adapter are subject to the final configuration of the dealer. The charging instructions in this manual may not be appropriate if a Type-C charging method is used.
4. Product Overview and Parts Identification
Familiarize yourself with the components of your BAOFENG UV-5R Mini radio:
Image: Front, side, and top views of the radio with numbered parts.
- Antenna
- PTT-A (Transmit Key)
- PTT-B (Transmit Key)
- SK1 (Flashlight & Custom Key)
- Power/Volume Knob
- Color Screen (1.77")
- Headset/Prog Port
- A/B Band Key
- Mic (Microphone)
- V/M (Freq/Chan Key)
- Scan Key
- EXIT Key
- MENU Key
- Keypad
- Up/Down Keys
- Type-C Port (Charging)
- Charging Light (Type-C)
- Flashlight
- TX/RX Light (Transmit/Receive)
- Battery Latch
5. Basic Operations
5.1 Turning Your Radio On and Off
- To turn ON: Turn the [Volume/Power] rotary knob clockwise.
- To turn OFF: Turn the [Volume/Power] rotary knob counterclockwise.
5.2 Setting the Volume
- To increase volume: Turn the [Volume/Power] rotary knob clockwise.
- To decrease volume: Turn the [Volume/Power] rotary knob counterclockwise.
CAUTION: Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.
5.3 Locking or Unlocking Keypad
To avoid accidentally changing radio settings:
- Press and hold the [*] key to lock the keypad until the screen displays the '🔒' icon.
- In lock mode, you can turn the intercom on and off, adjust the volume, receive, transmit, send call tones, send emergency alerts, and listen to channels. All other functions remain locked.
- In lock mode, press and hold the [*] key again to unlock the keypad until the '🔒' icon is no longer displayed.
5.4 Keypad Entry
You can enter radio aliases, channel aliases, numbers, etc., using the radio's numeric keypad.
- To switch between input methods, press the [#1] key.
- Press 1 to enter a special character (except in numeric input mode, where 1 is entered).
- Press 0 to enter a space (except in numeric input mode, where special characters are entered).
5.5 Select a Channel
The channel is the channel through which the signal is transmitted.
- Press the [V/M] button to toggle between VFO and channel mode to select channel mode.
- Press the Up/Down buttons or rotate the encoder to select the desired channel.
- Enter the channel number using the keypad (e.g., enter 064 for channel 64).
5.6 Channel Memory
In Frequency and Standby mode, you can store frequencies and parameters.
- Press [MENU] [3] [MENU] [1] [5]. The screen will display "MEMCH".
- Press [MENU] to enter the function.
- Press the Up/Down buttons or rotate the encoder to select the channel.
- Press [MENU] to store it. A sound tone will confirm successful storage.
- Press [EXIT] to return to standby mode.
NOTE: If you want to set CTCSS tones, DCS codes, or frequency offset, you must do so before storing the channel. Stored channels are displayed as CH-, other channels have no CH- display.
5.7 Delete a Channel (DEL-CH)
In VFO mode and standby mode:
- Press [MENU] [3] [MENU] [1] [6]. The screen will display "DELCH".
- Press [MENU] to enter the function.
- Press the Up/Down buttons or rotate the encoder to select the channel you want to delete.
- Press [MENU] to confirm.
- Press [EXIT] to return to standby mode.
NOTE: Channel 1 cannot be deleted.
5.8 Main Band/Sub Band Switch
In standby mode, press the [A/B] key to toggle between the A and B bands. The highlighted band is the main band; the darker displayed band is the sub-band.
5.9 VFO/Channel Switch
Press the [V/M] button to switch between VFO and channel display. VFO mode will display the 'VFO' icon. MR mode will display the channel serial number.
5.10 Setting the VFO Frequency
Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel.
- Input the VFO frequency directly with the keypad.
- Press the Up/Down buttons or rotate the encoder to adjust the VFO frequency in the set frequency step.
5.11 Call Service
All radios in the group must be set to the same channel and sub-code to communicate. To ensure optimal reception volume, keep the distance between the microphone and your mouth at 2.5 cm to 5 cm when transmitting.
- Initiate a call (PTT-A): Select a channel, press and hold the [PTT-A] key. The radio transmits on segment A (upper screen), and the red indicator light is on. Speak into the microphone with a normal voice tone.
- Initiate a call (PTT-B): Press and hold the [PTT-B] key. The radio transmits on the B segment (lower screen), and the red indicator light is on. Speak into the microphone with a normal voice tone.
- Receive a call: After releasing the [PTT] key, the radio is in a receivable state. When receiving a call, the green indicator light is on.
Note: In standby, press and hold the 8 key to toggle the transmission power.
5.12 Emergency Alarm
Emergency alarm allows the terminal to seek help from companions or a control center during an emergency.
- In standby mode, press the preset [SOS] key to enable or disable the emergency alarm function.
5.13 Flashlight
- In standby mode, press the preset 🔦 key to turn the flashlight on or off.
5.14 FM Radio Function
Set the [SK1] key to the radio function via Menu >> Radio Set >> Press SK1.
Turn on the radio and press the SK1 key [FM Radio] to enter radio mode. The screen displays the tuning frequency.
- Press the Up/Down key to search for radio channels at the preset step frequency.
- Press the [#1] key to search for radio channels automatically. The screen displays 'SEEK...'.
- Press [EXIT] key to switch frequency band between 65.0/75.0MHz.
- Press SK1 key [FM Radio] to exit radio mode.
5.15 Monitor
Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals on the current channel. This also allows you to adjust the volume when not receiving. Release the [Monitor] key to exit monitor mode.
5.16 Frequency Search
Press the pre-programmed [SEARCH] key or press and hold 🔍 key. The radio enters frequency search state, and the screen displays "SEARCH...". Press [#1] key to switch the searching band (VHF/UHF, etc.). The frequency and CTCSS/DCS code will be displayed after searching is completed. Press [MENU] to save the channel.
5.17 Reverse Frequency Function
Short press the [*✪] key in relay mode to invert the receive and transmit frequencies. The screen shows the 'R' icon. This function is often used in repeater channels and is effective when there is a frequency difference between the receive and transmit frequencies.
5.18 Talk Around Function
In repeater mode, press [*☑] to switch between Talkaround Mode and Repeater Mode. The screen displays both 'T' and 'R' icons. In Talkaround mode, the receive frequency is equal to the transmit frequency.
5.19 Repeater Activation Tone
Turn on the radio, press and hold the [PTT] key, then press the [SK1] to transmit 1750Hz audio to activate a repeater in hibernation.
5.20 Voice-Activated Transmit (VOX)
Enable VOX function to transmit automatically via voice without pressing the PTT key. Transmission stops automatically when speech stops, and the radio waits for receiving.
To enable VOX:
- In Standby status, press [MENU][2][MENU][4] to enter Vox Switch.
- Press [MENU][2][MENU][5] to enter Vox Level, press Up/Down to select VOX level (1-9). The smaller the value, the higher the sensitivity. The 'V' icon is displayed at the top of the screen. Default is off.
- Press [MENU] key to save the setting and return to the upper menu.
To turn off VOX, select OFF OFF, and the 'V' icon disappears.
5.21 Dual Watch
When in Dual Watch mode, the radio can receive the frequency set for channel A or B.
- Press [MENU] [2] to enter Radio Set.
- Press [MENU] + Up/Down to select "15 Dual Watch".
- Press [MENU] key to enter Dual Watch Setting, press Up/Down to select "On".
- Press [MENU] key to save and return to the upper menu. The dual watch function will be turned on, and the icon 'D' will be displayed on the first line of the screen.
To turn off Dual Watch, repeat the above steps and select "Off". The icon 'D' disappears from the first line of the screen. The sub-band displays the 📶 icon.
5.22 Stopwatch Function
Press and hold the [MENU] key to enable the stopwatch function.
- Press the [MENU] key to start the stopwatch.
- Press the [MENU] key again to stop the stopwatch.
- Press the [EXIT] key to exit the stopwatch function.
5.23 Weather Radio/Scan Weather Channel
Your radio has a NOAA Weather Radio function to receive weather reports from designated NOAA stations, and a NOAA Weather Scan function to scan all 10 channels.
- To turn NOAA Weather Scan on, press and hold the [0] key for 3 seconds. The ☁ icon appears, and the radio enters Weather band mode.
- Press and hold the [#1] key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding [#1] key for 3 seconds during a NOAA weather scan will stop the scan.
- After stopping NOAA weather scan, you can manually select the weather channel by pressing the Up or Down key.
- To exit Weather Radio broadcast mode, press the ☁ key or [PTT] key.
Weather Channel Frequencies and Names:
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| CH-01 | 162.550 | CH-06 | 162.500 |
| CH-02 | 162.400 | CH-07 | 162.525 |
| CH-03 | 162.475 | CH-08 | 161.650 |
| CH-04 | 162.425 | CH-09 | 161.775 |
| CH-05 | 162.450 | CH-10 | 163.275 |
NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
6. Advanced Features and Menu Functions
6.1 Functional Features Overview
- 6-band scan receiver: FM78-108MHz; AM108-136MHz; VHF136-174MHz, UHF400-520MHz, 350-390MHz
- Transmit frequency: VHF144-148MHz; UHF420-450MHz
- 5W/2W RF output, dual PTT transmitter
- Wireless read/write frequency
- 1.44" TFT large screen, full keyboard, full open menu operation, local channel storage and deletion
- Full keyboard manual frequency input, 999 channel memory
- One-click frequency pairing, easy pairing and grouping.
- Relay function settings: frequency difference, frequency difference direction, relay activation audio settings
- Alarm function (three types of alarm settings), to protect your security
- Built-in input method, supports local editing of channel name, receiving frequency, transmitting frequency
- DTMF encoding and decoding function, 20 DTMF calls
- Frequency hopping function
- Side button function customization: radio, scan, sweep, voice control, flashlight, alarm
- FM radio function (receive frequency 78~108MHz)
- Automatic or manual keypad lock, backlight selection
- Support Type-C charge, more convenient range
6.2 Using the Menu
Using with Arrow Keys:
- Press the [MENU] button to enter the menu.
- Use the Up/Down buttons or the encoder to navigate between menu items.
- Once you find the desired menu item, press [MENU] again to select that menu item.
- Use the Up/Down buttons or the encoder to select the desired parameter.
- To confirm your selection, press [MENU] to save your setting and return to the main menu. To cancel changes, press [EXIT] to reset the item and exit the menu.
- To exit the menu at any time, press the [EXIT] button.
Using with Short-Cuts:
- Press the [MENU] button to enter the menu.
- Use the numerical keypad to enter the number of the menu item.
- To enter the menu item, press the [MENU] button.
- For entering the desired parameter, you can use arrow buttons or the numerical keypad for short-cut code.
- To confirm your selection, press [MENU] to save your setting and return to the main menu. To cancel changes, press [EXIT] to reset the item and exit the menu.
- To exit the menu at any time, press the [EXIT] button.
6.3 Shortcut Menu Operations
| Menu # | Name | Setting | Description |
|---|---|---|---|
| 1 | Freq Ranger | NNNNnnn | Input VFO range lower and upper frequency |
| SCAN | Time | Time Operation - scanning will resume after a fixed time has passed | |
| Carrier | Carrier Operation - scanning will resume after the signal disappears | ||
| Search | Search Operation - scanning will not resume | ||
| 2 | Scan Memory | ALL | RX_TX are saved (default is all, encoding and decoding are the same) |
| DECODER | Save only in Transmitter CTCSS/DCS | ||
| ENCODER | Save only in Receiver CTCSS/DCS | ||
| 3 | Step | 2.5-100K | Selects the amount of frequency change in VFO/Frequency mode when scanning or pressing the ▲ or ▼ keys. |
| 4 | Squelch | OFF, LEVEL1-LEVEL5 | Squelch silences the receiver when there is no signal. Setting the squelch to 0 will open up the squelch entirely. |
| OFF | Turn off radio sleep. The battery consumption is large, and the standby time may be shortened | ||
| 5 | Power Save | ON | Turn on radio sleep. Turning on is more power efficient, but you might miss the first few syllables before the RX turns on. |
| OFF | Turn off the radio VOX. | ||
| 6 | VOX Switch | ON | Turn on the radio VOX. |
| LEVEL1-LEVEL9 | When enabled it is not necessary to push the [PTT] button on the transceiver. Adjust the gain level to an appropriate sensitivity to allow smooth transmission. | ||
| 7 | VOX Level | 0.5......2.0s | When the VOX is enabled, set up the VOX delay to help to extend the transmission time to avoid stopping a transmission too early. 0.5s-2s, Step 0.1 second. a total of 16 times offered. |
| 8 | VOX Delay | OFF | Allow continuous launch, launch time is not limited |
| 15;30;45...180 | Maximum allowed time for transmission while holding down the PTT key. | ||
| 9 | TOT | OFF | Disable TOA function |
| 10 | TOA | 1......10 | Activate TOA function. Range 0-10 seconds, Step 1 second. |
| OFF | Disable voice prompts | ||
| 11 | Voice | ON | Activate voice prompts |
| Chinese | Display menus and voice prompts in Chinese language | ||
| 12 | Language | English | Display menus and voice prompts in English language |
| OFF | Disable ROGER function. Release PTT key without ROGER audio. | ||
| 13 | ROGER | BEEP | Activate the ROGER function. Sends an end-of-transmission tone to indicate to other stations that the transmission has ended. |
| TONE 1200 | Activates the ROGER function. Sends the DMC1200 transmission end tone to indicate to other stations that the transmission has ended. | ||
| OFF | Disable key confirmation tone. | ||
| 14 | Beep | ON | Activation key to confirm tone. Allows audible confirmation of a key press |
| ALWAYS ON | The backlight is always on. | ||
| 15 | BackLight | 5......20 | Set the backlight off time in no-operation delay time. 5-20, step value is 5. |
| PICTURE | Show preset picture when radio is on | ||
| 16 | Power on | OFF | Disable dual table, dual receive. |
| ON | Monitor [A] and [B] at the same time. The display with the most recent activity ([A] or [B]) becomes the selected display. | ||
| 17 | Dual Watch | OFF | Disable automatic keypad lock. Allow manual keypad lock (press and hold the 🔒 key to lock/unlock the keyboard) |
| ON | When ON, the keypad will be locked if not used in 8 seconds. Pressing the 🔒 key for 2 seconds will unlock the keypad. | ||
| 18 | AutoLock | On Site | Sounds alarm through your radio speaker only |
| 19 | Alarm Mode | Send Sound | Transmits a cycling tone over-the-air |
| Send Code | Transmits '119' (911 in reverse) followed by the ANI code over-the-air | ||
| 20 | Alarm Tone | OFF | The radio speaker blocks the alarm sound. |
| ON | The radio speaker sounds an alarm | ||
| 21 | ANI-Edit | 100 | View the ANI ID, and if necessary, will allow to change the ANI ID |
| 22 | Display ANI | OFF | Disable the ANI code display function |
| ON | Enable ANI code display | ||
| 23 | DTMF-ST | OFF | No DTMF Side Tones are heard |
| DT-ST | Side Tones are heard only from manually keyed DTMF codes | ||
| ANI-ST | Side Tones are heard only from automatically keyed DTMF codes | ||
| DT+ANI | All DTMF Side Tones are heard | ||
| 24 | PTT-ID | OFF | No ID is sent. |
| BOT | The selected S-CODE is sent at the beginning | ||
| EOT | The selected S-CODE is sent at the ending | ||
| BOTH | The selected S-CODE is sent at the beginning and ending | ||
| 25 | PTT-DLY | 100-3000ms | Signal code sending delay. PTT-ID Delay (milliseconds) |
| 26 | ALERT | 1000Hz | PTT + SK1 = Transmits 1000Hz Tone Burst |
| 1450Hz | PTT + SK1 = Transmits 1450Hz Tone Burst | ||
| 1750Hz | PTT + SK1 = Transmits 1750Hz Tone Burst | ||
| 2100Hz | PTT + SK1 = Transmits 2100Hz Tone Burst | ||
| 27 | TAIL | OFF | Disable Squelch Tail Elimination. |
| ON | Enable Squelch tail elimination. to prevent any squelch tails from being heard. | ||
| 28 | Press SK1 | FM Radio | FM Radio on/off |
| SCAN | SCA on/off | ||
| SEARCH | Search on/off | ||
| VOX | VOX on/off | ||
| LAMP | Flashlight on/off | ||
| SOS | SOS on/off | ||
| 29 | Reset | VFO MODE | Reset the radio's VFO menu to factory defaults (no reset for bank, scan settings) |
| RESET ALL | Resets the radio to factory defaults, with some exceptions. | ||
| 30 | CH.NAME | Channel 1 | View channel name, allows to rename the current channel. Press the ⌨ key to switch the input method, allowing the input of letters, numbers and symbols. |
| 31 | RX Frequency | View the current channel Receiver frequency. | |
| 32 | TX Frequency | View the current channel Transmitter frequency. | |
| 33 | Trans Power | High | Selects between HIGH transmitter power when in VFO/Frequency mode. |
| Low | Selects between LOW transmitter power when in VFO/Frequency mode. | ||
| 34 | Bandwidth | Wide | Wideband (25 kHz bandwidth) |
| Narrow | Narrowband (12.5 kHz bandwidth) | ||
| 35 | RX CTCSS | OFF;67-254.1 | Mutes the speaker of the transceiver in the absence of a specific and continuous sub-audible signal. If the station you are listening to does not transmit this specific and continuous signal, you will not hear anything. |
| 36 | RX DCS | OFF;023N-7541 | Mutes the speaker of the transceiver in the absence of a specific low-level digital signal. If the station you are listening to does not transmit this specific signal, you will not hear anything. |
| 37 | TX CTCSS | OFF;67-254 | Transmits a specific and continuous sub audible signal to unlock the squelch of a distant receiver (usually a repeater). |
| 38 | TX DCS | OFF;023N-7541 | Transmits a specific low-level digital signal to unlock the squelch of a distant receiver (usually a repeater). |
| 39 | Encryption | OFF | Disable encrypted mode, your conversations are not private. |
| ON | Activating encryption mode ensures the privacy of your conversations. To use the Encryption function, the other part of the radio must also have Encryption activated and must be tuned on the same DCS code. | ||
| 40 | Signaling | 1-20 | Selects 1 of 20 DTMF codes. The DTMF codes are programmed with software and are up to 3 digits each. |
| 41 | CH-MDF | NAME | MR/Channel mode is displayed in NAME format. Note: NAME allows CPS program or edit in the channel name (Munu 1). |
| FREQ | MR/Channel mode is displayed in frequency format. | ||
| CH | MR/Channel mode is displayed in CH format. | ||
| 42 | SP-Mute | QT | When radios is set in this mode, the monitor feature is activated only when the radio receives the correct CTCSS/DCS. |
| QT+DTMF | With this option, the monitor is activated when the radio receives the correct CTCSS/DCS and the correct DTMF code. | ||
| 43 | SCAN ADD | OFF | Forbid the current channel to join the scan group. |
| ON | Add the current channel to the scan group. | ||
| 44 | Busy Lockout | OFF | The [PTT] button on the channel is always allowed. |
| ON | Disables the [PTT] button on a channel that is already in use. The transceiver will sound a beep tone and will not transmit if the [PTT] button is pressed when a channel is already in use. | ||
| 45 | OffSet | Specifies the difference between the TX and RX frequencies | |
| 46 | Direction | None | TX = RX (simplex). Disable access to repeaters in VFO/Frequency mode |
| Plus | Plus frequency shift direction. TX will be shifted higher in frequency than RX | ||
| Minus | Minus frequency shift direction. TX will be shifted lower in frequency than RX | ||
| 47 | CH_Memory | CH001-CH999 | This menu is used to either create new or modify existing channels (1 through 999) so that they can be accessed from MR/Channel Mode. |
| 48 | CH_Delete | CH001-CH999 | This menu is used to delete the programmed information from the specified channel (1 through 999) so that it can either be programmed again or be left empty. |
7. Wireless Programming
You can program the radio wirelessly using a dedicated app. Before programming, install the app by scanning the QR codes below:
Android App
iOS App
Radio Operation for Wireless CPS:
- Press [MENU] + [4] to enter Wireless CPS.
- Press [MENU] + Up/Down to select "On". The 📶 icon will be displayed on the first line of the screen.
Using the Radio APP:
After opening the app, allow Bluetooth and location services on your mobile phone. Select the "5Rmini Series" walkie-talkie model, connect the radio, and click "Walkie-talkie". A confirmation message will indicate successful connection, and you will return to the home page.
- Read the radio data: After frequency reading, click to enter program details. In the program details interface, you can program channel information, frequency mode, and optional functions.
- Save Profile: The programmed profile allows you to save it as a new profile. If you select "Replace Program", click "Replace Program" and save.
- Write data to radio: Click the home page, select the program, click 'Write' to enter write frequency. The radio will restart automatically after writing the frequency.
8. Technical Specifications
Image: Technical specifications and dimensions.
| Feature | Specification |
|---|---|
| Receiver Frequency | FM 76-108 MHz; VHF 136-174MHz, UHF 400-520MHz, 350-390MHz |
| Transmission Frequency | VHF 144-148MHz, UHF 420-450MHz |
| Channel Spacing | 25.0KHz (Wide) / 12.5KHz (Narrow) |
| Memory Channel | 999 Groups |
| Operation Voltage | DC 7.4 V ±10% |
| Dimensions | 108mm × 52mm × 37mm (No antenna) |
| Weight | 200g (Battery pack included) |
| Transmission current | ≤1600mA |
| Receive Sensitivity | 0.25µV (12dB SINAD) |
| Rated Audio Power Output | 1W @ 16 ohms |
| Receive current | ≤380mA |
| Connection for accessories | 2 pin Kenwood jack |
| Antenna impedance | 50 Ohm |
NOTE: All specifications may be modified without prior notice or liability.
9. Troubleshooting
If you encounter issues with your radio, please refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Radio won't turn on | Low battery; Battery not properly installed; Power knob off | Charge battery; Reinstall battery; Turn power knob clockwise |
| No sound/low volume | Volume too low; Squelch level too high; Headset not connected properly | Increase volume; Adjust squelch level; Reconnect headset |
| Cannot transmit or receive | Wrong frequency/channel; Antenna damaged; Battery low; Keypad locked | Verify frequency/channel settings; Replace antenna; Charge battery; Unlock keypad |
| Interference/poor signal | Obstructions (mountains, trees); Distance too far; Weak signal area | Move to an open area; Reduce distance; Consider a higher power radio or larger antenna for challenging terrain |
| Wireless programming issues | Bluetooth off; Location services off; Incorrect app version; Radio not in Wireless CPS mode | Enable Bluetooth and location; Ensure correct app is installed; Set radio to Wireless CPS mode (MENU + 4) |
10. Maintenance
Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and to enjoy this product for many years.
- Do not attempt to open the radio for any reason! The radio's precision mechanics and electronics require experience and specialized equipment; for the same reason, the radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty.
- Do not store the Radio under direct sunlight or in hot areas. High temperatures can shorten the life of electronic devices and warp or melt certain plastics.
- Do not store the radio in dusty and dirty areas.
- Keep the Radio dry. Rainwater or damp will corrode electronic circuits.
- If the Radio diffuses a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
- Do not transmit without an antenna.
10.1 Battery Maintenance Instructions
To help your battery work normally or prolong its life, observe the following:
- Accumulated dust on the charging connector may affect normal charging. Use a clean and dry cloth to wipe it regularly.
- It is recommended to charge the battery between 5°C and 40°C. Violation of this limit may reduce battery life or cause leakage.
- To fully charge a battery attached to the product, turn the product off.
- Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight for a long time or place it close to other heating sources.
- Do not squeeze, penetrate, or remove the housing of the battery.
11. User Tips
- Optimal Performance: For environments with many mountains and trees, consider using a radio with higher power and a larger antenna for better range and signal penetration.
- Interoperability: This equipment works very well and can be paired with other compatible radio equipment.
12. Warranty and Support
For warranty information and technical support, please refer to the documentation provided at the time of purchase or contact your authorized BAOFENG dealer. Keep your proof of purchase for warranty claims.
A user manual in PDF format is available for download: View User Manual (PDF)