1. Safety Information
To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use.
When operating the device, always verify proper testing procedures and strictly adhere to the instructions provided. As automotive electrical systems may vary, you must assess potential risks and ensure a safe testing environment.
Always observe all safety warnings, use appropriate tools, and disconnect power sources when necessary. Improper operation may result in personal injury, equipment damage, or voided warranty.
Safety Messages
Safety messages use standardized signal words to indicate hazard levels and prevent injuries or equipment damage:
DANGER
Will result in death or serious injury if ignored
Indicates an immediately life-threatening hazard.
WARNING
Could result in death or serious injury if ignored
Indicates a potentially dangerous situation.
Safety Instructions
This manual covers known safety hazards, but cannot anticipate all possible risks. You are responsible for ensuring safe operating conditions and procedures.
DANGER
- Always ventilate the service area when engine is running or use building exhaust removal system if available.
- Carbon monoxide is odorless and deadly - can cause loss of consciousness or death.
WARNINGS
Always conduct testing in a safe, controlled environment.
- Wear ANSI-approved safety goggles during all operations.
- Keep all objects away from moving or hot engine components.
- Ensure proper ventilation to avoid toxic exhaust fumes.
- Secure the vehicle in PARK (automatic) or NEUTRAL (manual) with parking brake engaged.
- Place wheel chocks and never leave the vehicle unattended during tests.
- Exercise extreme caution around ignition systems - hazardous voltages are present.
- Maintain an ABC-rated fire extinguisher within immediate reach.
- Never connect/disconnect test equipment with ignition on or engine running.
- Keep all test equipment clean, dry and free from contaminants.
- Never operate test equipment while driving - focus solely on testing.
- Strictly follow the vehicle service manual's diagnostic procedures.
- Verify full battery charge and secure DLC connections before testing.
- Never place test equipment near the distributor due to EMI risks.
2. Device Description
The D501, D502, and D503 are a series of compact, dedicated diagnostic devices. They share the same powerful and comprehensive functionality, with the only difference being the specific vehicle brands they serve:
- D501: Engineered specifically for GM vehicles (including Buick, Chevrolet, Cadillac, and GMC).
- D502: Engineered specifically for Ford vehicles.
- D503: Engineered specifically for BMW Group vehicles (including BMW, Mini, and Rolls-Royce).
This powerful device offers comprehensive coverage of all vehicle systems, from engine and transmission to ABS, airbag, and HVAC. It supports essential special functions like Oil Reset and EPB Reset, and also provides full OBDII modes, bi-directional active tests, and FCA security access for advanced calibration.
With its in-depth vehicle-specific capabilities, the device ensures maximum compatibility and diagnostic power for your Ford car or truck, enabling you to accurately identify issues, perform maintenance, and verify repairs with confidence.
Beyond these integrated capabilities, the device is built on an advanced platform that supports powerful add-on services, such as J2534 programming, available for purchase within the app to meet professional diagnostic needs.

Figure 2.1: VDIAGTOOL D502 Key Features
3. Setup
3.1 Download & Install App
To get started, download the VDIAGTOOL app from the Google Play Store or Apple App Store. You can also visit our official download page: www.vdiagtool.com/support/downloads to get the download link.

Figure 3.1: Quick Start Guide for VDIAGTOOL D502
3.2 Registration & Activation
To begin using the app, you will need to register an account to bind your VCI device.
- Enter your email address and password.
- Tap 'Create Account' - a verification code will be sent to your email.
- Enter the verification code and tap 'Next' to complete the registration.
Note: If you don't receive the verification email, please check your spam or junk folder.
3.3 Adding a Device
If this is your first time using the device, you will need to add and activate it.
You can add the device by either:
- Scanning the QR code on the device, or
- Manually entering the serial number and activation code.
3.4 Connect the Device
After successfully adding your device, the app will prompt you to connect it to begin diagnostics.
This device is powered through the vehicle's OBD-II port and operates on 12V power from the vehicle. It will automatically turn on once plugged into a compatible Data Link Connector (DLC).
Connection Steps:
- Insert the device firmly into the vehicle's OBD-II port. Ensure it is fully seated and secure.
- Start the vehicle's engine.
- Enable Bluetooth on your phone, then select and pair the device in your Bluetooth settings. The connection will establish automatically within approximately 15 seconds.
IMPORTANT: Do not supply power to the device via the Type-C port while it is communicating with the vehicle.
Note: A green VCI indicator in the upper right corner of the app confirms a successful connection. You may then proceed with vehicle diagnostics.
4. Operating Instructions
4.1 Main Menu Overview
Upon launching the app, you will enter the main menu, which includes the following options:
- Auto Scan: Automatically identifies the vehicle's VIN and performs a comprehensive scan of all available electronic control modules for diagnostics.
- OBD II: Accesses the OBDII functions menu.
- Diagnosis: Opens the diagnostic menu for your dedicated vehicle brand. The system will automatically identify your vehicle via VIN, or you can manually select the specific model, year, and configuration to begin comprehensive full-system diagnostics. This section also provides access to the DEMO program and standard OBDII tests.
- Special Function: Provides a range of common maintenance services used by both DIY enthusiasts and professionals for everyday auto repair tasks.
- Updates: Allows internet-based updates of the diagnostic software.
- Report: View saved diagnostic reports, export them as PDF files, or share via email.
- Mall: Purchase additional features and functions.
- Home: Returns to the main menu screen.
- Application Center: Navigates to the APP center.
- Me: Manage account settings, configure device preferences, update the system, and adjust other personal settings.
4.2 Diagnose Vehicles
Accurate vehicle identification is required for the diagnostic tool to establish communication and perform diagnostics. The identification process is menu-guided—follow the on-screen prompts to enter the necessary information. Specific steps may vary depending on the vehicle's model and year.
You can identify a vehicle using one of the following four methods:
4.2.1 Auto Scan
Tap "Auto Scan" icon on the main menu screen, and the tool will scan the vehicle VIN and decode the VIN for vehicle identification automatically.
Note: Auto Scan does NOT work on all vehicles. When Auto Scan fails, try Diagnosis instead.
4.2.2 Diagnosis
Tap "Diagnosis" icon on the main menu screen, the tool will bring up vehicle selection menu.
Under this menu, you can also tap the Auto Scan to enter the diagnosis menu. Or, you can manually input the vehicle VIN number (17 digits).
Note: Some vehicle VINs may not be decodable. When Auto Scan and Manual Input fail, try manual vehicle selection instead.
4.2.3 Automatic Detection
Tap Manual Diagnosis, select the specific brand from your dedicated vehicle family (e.g., Buick, Chevrolet, or Cadillac for GM vehicles), and then tap Automatic Detection to allow the device to identify the connected vehicle.
Note: Automatic Detection is not supported on all vehicle models. If this method fails, please try Manual Selection instead.
4.2.4 Manual Selection
When the "Auto Scan", "Manual Input" and "Automatic Detection" fail to identify the vehicle, you can always try "Manual Selection" to identify the vehicle and proceed to diagnosis. Manual Selection is the most reliable vehicle identification option.
To identify a vehicle manually:
- Tap Diagnosis.
- From the main menu of supported brands, select the specific brand of your vehicle.
- Select Manual Selection.
- Specify the model year, model name, and any subsequent options until Automatic Scan and Full System Diagnosis appear.
4.3 Diagnosis Functions
When you enter the vehicle model diagnostic menu, it will show the following functions:
4.3.1 Automatic Scan
It will automatically scan all systems of your vehicle to see if there are any problems.
4.3.2 CAN Fast Scan (After 2005)
Rapidly scans all accessible vehicle systems for post-2005 vehicles using CAN protocol communication.
4.3.3 Full System Diagnosis
Select a specific vehicle control module for diagnostics when you already have an idea which system may be causing issues.
4.4 Diagnostics (Detailed)
After successful vehicle identification, the device can scan and access the vehicle's electronic control systems to Read DTC, read Live Data, Read Freeze Frame, access ECU information, and perform tests such as active tests (bi-directional controls or actuator tests), and more.
4.4.1 Read ECU Information
This function is to read ECU version information, which is the equivalent of System Identification or System Information in some electronic control systems, which means to read ECU-related software and hardware versions, models, and production date of the diesel engine, part number, etc.
4.4.2 Read DTC
Displays diagnostic trouble code (DTC) records stored in the vehicle's electronic control modules. Selecting this option may open a submenu with additional viewing choices.
If the tool displays "System is OK" or "No Trouble Code", this may indicate:
- No relevant fault codes are stored in the ECU;
- The fault is not within that specific ECU's domain (e.g., mechanical or circuit issues);
- A sensor signal is abnormal but still within its operational range — such cases can be further analyzed using Live Data (PID).
4.4.3 Clear DTC
Erases both current and historical DTC records, along with related data, from the vehicle's electronic control modules.
After initiating the erase command, the ECU will verify whether the issue has been resolved over several drive cycles. Note that:
- Some faults can be detected immediately with the ignition on, even if the engine is off.
- Other faults require specific conditions to be met (e.g., engine coolant temperature, vehicle speed, or throttle position within certain ranges for a defined duration) before they can be detected again.
4.4.4 Live Data
Displays Live Data from vehicle sensors and control modules. View data in list or graph formats, set custom value thresholds, and monitor up to 8 sensors simultaneously in list, individual graph, or merged graph views.

Figure 4.1: 8-IN-1 Live Data Stream Graphing
4.4.5 Read Freeze Frame
When a fault code is triggered, the vehicle ECU will save related data at that moment to generate a freeze frame. It is usually used to analyze the root cause that triggers the fault code, together with fault codes and PID data.
Freeze frame displayed varies across vehicles. Some vehicles may not have the option of freeze frame which means that the vehicle does not support this function.
4.4.6 Actuator Tests
Actuator Tests, also referred to as bi-directional controls, verify the operation of specific actuators—including solenoids, valves, and relays.

Figure 4.2: Bi-directional Control Examples
4.5 OBD II Functions
Global OBD uses the following five communication protocols:
- SAE J1850 PWM
- SAE J1850 VPW
- ISO 14230-4 (KWP2000)
- ISO 9141-2
- ISO 15765-4 / SAE J2480
4.5.1 Auto Scan & Protocol Selection
There are two methods to access OBDII data from the connected vehicle:
- Auto Scan: When this option is selected, the diagnostic tool automatically attempts to communicate using each available protocol to identify the one utilized by the vehicle.
- Protocol Selection: A communication protocol is a standardized method for data exchange between an ECM and the diagnostic tool. If the vehicle's protocol is known, you can manually select it to establish a direct connection.
4.5.2 Help
This section provides support information, including DLC location, a DTC library, common abbreviations, and background details such as OBDII modes.
4.5.3 Modes of OBDII
Menu options typically include:
- Read Trouble Code (Stored, Pending, Permanent Codes)
- Clear Trouble Code
- Live Data
- Read Freeze Frame
- Read ECU Information
- Component Test (Mode $08)
- On-Board Monitor Test (Mode $06)
- O2S Monitoring Test (Mode $05)
- I/M Readiness (Smog Check)

Figure 4.3: Full OBD2 Functions
5. Special Functions (Maintenance & Service)
This chapter introduces scheduled service and maintenance functions, known as "Special Functions". These are menu-driven commands that guide you through each process.
Note: Available functions differ between the D501, D502, and D503 devices, and also depend on the connected vehicle's year, model, and configuration.
Follow the on-screen instructions to select options, enter values, and perform actions as prompted.

Figure 5.1: Common Special Functions
5.1 Power Balance
This function sequentially disables individual fuel injectors and monitors the corresponding drop in engine RPM. By comparing the power output reduction across cylinders, it identifies underperforming or malfunctioning cylinders based on their relative contribution to engine power.
5.2 ABS Bleeding
The Anti-Lock Braking System (ABS) prevents immediate tire lock-up during braking. Maintaining ABS in optimal condition ensures full braking effectiveness, reduces braking time and distance, prevents skidding and loss of control during emergency stops, improves driving stability and steering control, and minimizes tire wear by avoiding excessive friction with the ground.
When air enters the ABS, the ABS Bleeding function must be used to purge the brake system and restore braking sensitivity.
When to Perform ABS Bleeding:
- After replacing the front or rear brake distributor pump
- Severe brake fluid loss
- Brake fluid replacement
5.3 TPMS Reset
This function supports learning, matching, and resetting operations for tire pressure sensors.
When to Perform TPMS Reset:
- After replacing tires
- When troubleshooting tire pressure-related issues
- When the tire pressure sensor signal is lost
Important: Some vehicle models require a TPMS activation tool for sensor matching. After resetting, driving for a period may be necessary to clear the fault light. Tire pressure imbalance can also trigger the tire pressure warning light. This function only works with pre-activated sensors. For new sensors, use a professional TPMS tool.
Even for the same vehicle model, the tire pressure monitoring system may vary depending on the region of manufacture. To accommodate these differences, the TPMS Reset function provides six regional sub-menus covering major automotive manufacturing regions: Korea, Japan, USA, China, Australia, and Europe.
5.4 Injector Coding
This function writes the identification code of a fuel injector into the ECU, enabling the ECU to recognize and accurately control the new injector.
Injector coding is required after replacing the ECU or an injector to ensure proper cylinder-specific fuel injection control. Coding is typically not necessary after cleaning. The injector identification includes both precision and type values.
5.5 EPB (Electronic Parking Brake)
The Electronic Parking Brake (EPB) reset function allows you to perform maintenance operations such as resetting the brake system, retracting or releasing brake pistons, and calibrating the G-sensor and vehicle level. It ensures safe and effective servicing of the electronic brake system, including deactivating/activating control systems, assisting with brake fluid procedures, and applying/releasing brakes after replacing pads or discs.
Typical Use Cases:
- After replacing worn brake pads or sensors, a reset is required to clear related fault codes and prevent false warnings.
- A reset is also necessary in the following situations:
- The brake pad or wear sensor has been replaced
- The brake pad indicator is illuminated
- The brake sensor circuit is shorted
- The servo motor has been replaced
5.6 Seat Calibration
Also referred to as Seat Configurations, this function is used to match or configure replaced or repaired seats equipped with memory functions.
5.7 Oil Reset
The diagnostic tool allows you to reset the engine oil life system, which estimates the optimal oil change interval based on driving conditions and climate. The oil life reminder must be reset after each oil change so the system can calculate the next service due date.
This function is used in the following scenarios:
- The service lamp is illuminated, indicating required maintenance. After servicing, reset the mileage or time to turn off the lamp and start a new service cycle.
- After an oil change or replacement of oil life monitoring sensors, the service lamp must be reset.
5.8 Control Unit Reset
This function resets the ECU software to resolve faults caused by abnormal operating temperatures or voltage fluctuations.
5.9 EPS Adaptation
The EPS Adaptation procedure permanently stores the current steering wheel position as the straight-ahead reference in the EPS control module's EEPROM. Before performing the adaptation, ensure the front wheels and steering wheel are precisely aligned in the straight-ahead position. The VIN is also read from the instrument cluster and stored in the EPS module's memory. Upon successful completion, all EPS-related fault codes will be cleared automatically.
This process establishes the zero reference point for straight-line driving, enabling the EPS ECU to accurately determine steering angle and provide appropriate assistive torque.
When to Perform EPS Adaptation:
After any of the following services:
- Replacing the steering angle sensor
- Replacing steering mechanical components (e.g., gearbox, column, tie rod, knuckle)
- Performing a four-wheel alignment
- Repairing the vehicle body
5.10 Gearbox Adaptation
This function performs transmission self-learning to improve shift quality after disassembly or repair, resolving issues such as shifting delays or harsh engagement.
5.11 Airbag Reset
This function is used to reset the airbag system and turn off the airbag warning light after replacing an airbag component. It can also clear crash data from the control module.
Note: Clearing crash data is only supported on specific vehicle models.
5.12 Throttle Adaptation
This function resets the throttle actuators and clears learned values stored in the ECU, restoring them to default settings. This ensures precise control of throttle or idle regulation and accurate adjustment of air intake.
5.13 Tire Size Reset
This function resets the tire size configuration in the vehicle system when tires are replaced or upgraded.
5.14 BMS Reset
The Battery Management System (BMS) Reset function enables the diagnostic tool to evaluate the battery state, monitor current, register battery replacement, and activate the vehicle's rest state. This process clears existing low-battery fault information and performs battery matching to ensure accurate power management.
When to Perform BMS Reset:
- After replacing the main battery, to clear previous fault data and prevent false detection by control modules.
- To rematch the control module and monitoring sensor for accurate battery usage tracking, avoiding error messages on the instrument cluster.
Failure to reset may disable electric features such as auto start-stop, one-touch sunroof, or automatic power windows.
5.15 Suspension
This function adjusts the vehicle height sensor and performs level calibration in air suspension systems. It is used after replacing the height sensor or control module, or when the vehicle level is incorrect.
5.16 Windows Initialization
This function restores the power window automatic operation and ECU memory by performing window matching, typically required after vehicle battery disconnection causes window malfunction.
5.17 Headlight
Also referred to as Headlight Adjustment, Headlight Matching, or AFS Reset, this function initializes the adaptive headlight system. It enables automatic headlight activation based on ambient light, and adjusts the lighting angle according to vehicle speed, body posture, and other driving conditions.
5.18 Transport Mode
Vehicles are placed in a partially activated state called Transport Mode during factory shipment to minimize battery drain. This function is used at the dealership to deactivate Transport Mode and fully enable all vehicle systems.
5.19 Coolant Bleeding
Also known as Electric Water Pump Activation, this function activates the electric water pump following its replacement to ensure proper coolant circulation.
5.20 Crank Sensor Relearn
This function performs crankshaft position variation learning to turn off the Malfunction Indicator Lamp (MIL).
It is required in the following cases:
- After replacing the engine ECU, crankshaft position sensor, or crankshaft flywheel.
- When a DTC indicating "tooth not learned" is present.
5.21 A/F Reset
This function resets or relearns the air/fuel ratio parameters to optimize combustion efficiency.
6. Reports
After completing diagnostics and returning to the main screen, tap 'Save' in the report generation form to create a diagnostic report. This report can be reviewed or shared later.
The report is available in two types:
- Diagnosis Report
- CSV View
6.1 Diagnosis Report
Diagnosis reports are automatically generated after performing diagnostic operations—such as auto-scanning, reading ECU information, retrieving trouble codes, or viewing live data. You can also manually generate a report by selecting DTC Report in the diagnostic menu.
All saved reports are available under the Report menu, where you can compare results, view details, or delete reports as needed.
From the report review screen, you can share the report via email or export it as a PDF file.
6.2 CSV View (Data Playback)
This feature enables you to replay recorded live data from the diagnostic process. Data recording begins only when you tap the Data Recording button during a live data session, and valid data is being displayed.
Recorded files can be accessed via Me → Related to me → CSV View.
Note: Recorded CSV View sessions cannot be exported and can only be played within the app.
7. Application Center
Application Center is a comprehensive hub designed to expand your diagnostic capabilities. It offers advanced tools and features to help you monitor, analyze, and troubleshoot vehicle systems efficiently.
Key functions include:
- Performance Test: Evaluate engine performance and identify potential issues through real-time diagnostics.
- Smog Check: Conduct emissions testing to ensure compliance with environmental regulations.
- Mode 6: Access detailed diagnostic data for deeper analysis of vehicle systems.
- MIL Status: Check the status of the Malfunction Indicator Light (MIL) to quickly identify active faults.
- OBD DTC Query: Retrieve and interpret Diagnostic Trouble Codes (DTCs) for precise troubleshooting.
- Vehicle Coverage: Check the compatibility. However, this is for reference only. For better compatibility confirm, please provide your device S/N, your vehicle VIN and the desired functions to our tech support team at support@vdiagtool.com.
- Warning Light Symbols: Identify and understand all dashboard warning lights, with detailed explanations for their causes.
8. User Profile / Settings
Profile serves as your personalized control center, where you can manage account settings, device configurations, and system updates.
This section allows you to:
- Customize Your Profile: Change your username and profile picture for personal identification.
- My Device: View essential details including model, serial number. You can also add another device or unbind your current device.
- CSV View: Replay Live Data recording.
- Subscription Service: Review active plans and available renewal options.
- Firmware Upgrade: Download the latest firmware to maintain peak device performance.
- Software Management: Manage installed applications and diagnostic modules.
- Other Settings: Configure preferences including language, units, and display options.
8.1 Other Settings
Tap the Other Settings to adjust the default settings and view the information of the app. There are several options available in the system setting:
- Language: The languages supported by the device are listed in Settings. The default language is set as English. If you need to switch to other languages, please contact the dealer or reach out to the tech support at support@vdiagtool.com to authorize the new language. Once authorized, go to Other Settings - Language and select the target language, then navigate to Updates to download and install all available target-language software packages.
- Unit: This setting provides 3 (three) sets of units to measure various sensor values:
- Metric Units: Centimeters, kilometers, grams, kilo, °C, litres, pa, kpa
- Imperial Units: Inch, foot, yard, oz, lb, °F, PSI, mile, gallon
- US Units: Inch, foot, yard, oz, lb, °F, PSI, mil, mile
- Clear Cache: Quickly free up storage space and resolve performance issues by removing temporary system files and residual diagnostic data with one simple action.
- About: Access essential information about your app including the current software version, User Agreement, Privacy Policy, and support contacts in one convenient location.
9. Updates
All the available software is shown on this page. You can choose to download the specific software individually by tapping the arrow button next to the required software or choose to update all available software at once by tapping 'Updates'.

Figure 9.1: Software Update Screen
10. User Tips
- Regular Updates: Ensure your device software is always up-to-date to benefit from the latest vehicle compatibility and diagnostic features.
- Battery Check: Always ensure your vehicle's battery is fully charged before performing any diagnostic tests to prevent data loss or incorrect readings.
- Secure Connection: Double-check that the D502 is firmly seated in the OBD-II port and that the Bluetooth connection is stable before starting any diagnosis.
- Review Reports: Utilize the diagnostic reports to track vehicle health over time and share with mechanics for clearer communication.
- Explore Special Functions: Familiarize yourself with the various special functions to perform common maintenance tasks efficiently and accurately.
11. Specifications
| Attribute | Value |
|---|---|
| Brand Name | VDIAGTOOL |
| Model | D502 |
| Item Type | Code Readers & Scan Tools |
| Communication Interface | OBD-II |
| Wireless Support | Bluetooth |
| Free Update Period | Lifetime |
| Software Update | Yes |
| Software Version | 2026 |
| Hardware Version | 2026 |
| Battery Included | No |
| Certification | CE |
| Origin | Mainland China |
| Package Length | 10 cm |
| Package Width | 8 cm |
| Package Height | 5 cm |
| Package Weight | 0.3 kg |
Package Contents:

Figure 11.1: VDIAGTOOL D502 Package Contents
- VDIAGTOOL VCI Main Unit
- Type C Cable
- User Manual (this document)
- Tool Kit
12. Warranty & Support
12.1 Limited Two-Year Warranty
This warranty is expressly granted to buyers who purchase the VDIAGTOOL product for resale or for use in the ordinary course of their business.
VDIAGTOOL warrants that the VCI device shall be free from defects in materials and workmanship for a period of two years (24 months) from the date of delivery to the original buyer.
This warranty does not cover any part that has been subjected to misuse, alteration, used for unintended purposes, or operated in a manner inconsistent with the product instructions. The exclusive remedy for any tool found to be defective under this warranty shall be, at VDIAGTOOL's option, repair or replacement of the product. VDIAGTOOL shall not be liable for any consequential or incidental damages arising from the use or inability to use the product.
12.2 Contact Us
Warranty & Technical Support
- Email: support@vdiagtool.com
- Website: www.vdiagtool.com
- US Hotline: +1-213-355-7171
- Online Form: https://www.vdiagtool.com/support/tech-support
Training Videos
Free product operation videos:
- Visit Training Center: https://www.vdiagtool.com/support/training-center
- Select Diagnostic Tools category
- Watch model-specific tutorials
13. Compliance Information
13.1 Regulatory Compliance Statements
United States (FCC)
FCC ID: 2BE93V01
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Interference Guidance:
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Canada (ISED)
IC: 32118-V01
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
13.2 RF Exposure & SAR (FCC & ISED)
This device complies with FCC and ISED Canada RF exposure guidelines. Its radiated output power is below the radio frequency exposure limits.
The Specific Absorption Rate (SAR) is measured using standard operating positions with the device transmitting at its highest certified power level. The FCC SAR limit is 1.6 W/kg. The device is designed to operate at multiple power levels to minimize exposure and uses only the necessary power to maintain communication.
To ensure compliance with RF exposure requirements, minimize human contact with the antenna during normal operation.
13.3 Additional Compliance (RoHS, CE & UKCA)
RoHS: This product is compliant with Directive 2011/65/EU on the restriction of hazardous substances.
CE: This product conforms to the essential requirements of the following European Directives:
- EMC Directive 2014/30/EU
- RED Directive 2014/53/EU
- Low Voltage Directive 2014/35/EU
UKCA: This product is declared to conform to the essential requirements of the relevant UK statutory instruments and carries the UKCA mark accordingly.
