Introduction
Thank you for choosing the BOAYAL handheld laser distance meter. To ensure safe and proper operation, please read these safety instructions and the user manual carefully before using this product. Failure to do so may result in hazardous laser radiation or electric shock.
This manual covers the DK series laser distance meters, including models with ranges of 40m, 60m, 80m, and 100m.
Safety Information
Laser Safety Instructions
- This product is a Class II laser product.
- DO NOT stare into the laser beam at any time when operating this product.
- DO NOT look directly into the beam with optical aids (e.g., binoculars, telescopes) to avoid causing serious laser radiation.
- DO NOT remove any safety labels on this product.
- Laser Type: 620-690nm, Class II, <1mW.
General Caution
- DO NOT use this product in an unstable situation.
- Keep the meter away from children.
- DO NOT disassemble or restructure the meter. Otherwise, it may lead to laser emission resulting in unnecessary personal injury.
- Keep this manual for future reference.
Product Overview
The BOAYAL Laser Distance Meter is a high-precision measuring device featuring dual horizontal bubbles for accurate leveling, an HD display, and multiple measurement modes.
Image: Front view of the BOAYAL Laser Distance Meter, showing the digital display and control buttons.
Key Features
- Two horizontal bubbles (longitudinal and transverse) for precise alignment.
- HD display with three lines of data, suitable for various light environments.
- Data storage for up to 20 groups of measurements.
- High-quality lens for accurate readings.
- Multiple measurement modes to meet diverse needs.
Image: Diagram illustrating the bithorizontal bubble levels (longitudinal and horizontal) on the device for precise measurement.
Image: The HD display showing three lines of data, with examples of visibility in both bright (day) and dim (night) environments.
Product Components
- Laser distance meter (1 pc)
- AAA battery (2 pcs - not included with all models, please check packaging)
- User manual (1 pc)
- Packing box (1 pc)
- Hand rope (1 pc)
Image: Detailed diagram of the laser distance meter's buttons and their corresponding functions, including short press and long press actions.
- Laser emitter
- Laser receiver
- Display screen
- Spirit bubble (top)
- Power key/Measuring key (Orange button)
- Minus key/Unit switch key (-/U button)
- Clear key/Exit key/OFF key (C/O button)
- Spirit bubble (bottom)
- Plus key/Reference switch key (+/d button)
- Function key/Sound key (Speaker icon button)
- Battery compartment
Setup
Battery Installation
The device requires 2x AAA alkaline batteries (not included). To install:
- Locate the battery compartment lid on the side of the device.
- Remove the battery compartment lid.
- Insert 2 AAA alkaline batteries, ensuring correct polarity (+/-).
- Replace the battery compartment lid securely.
Image: Illustration of how to open the battery compartment and insert AAA batteries into the device.
Operation
1. Power On/Off
- To Power On: Short press the Power/Measure key (orange button). The screen will display information quickly.
- Laser Auto Shut-off: The laser point will automatically shut down if there is no operation for 30 seconds.
- Instrument Auto Shut-off: The entire instrument will shut off after 180 seconds of inactivity.
- To Manually Turn Off: Long press the Clear/Exit/OFF key (C/O button).
2. Change Measurement Reference
The default measuring reference is the bottom of the meter. To change the reference point:
- To switch to top reference: Long press the Plus key/Reference switch key (+/d button).
Image: Illustration of how the measurement reference can be switched between the front (pre-baseline) and rear (post-baseline) of the device.
3. Unit Conversion
The factory default unit is meters (m). To change the unit:
- For distance units (m, ft, in): Long press the Minus key/Unit switch key (-/U button) to cycle through m → Ft → In.
- For area units (m², ft², in²): In Area Measurement Mode, long press the Minus key/Unit switch key (-/U button) to cycle through m² → Ft² → In².
- For volume units (m³, ft³, in³): In Volume Measurement Mode, long press the Minus key/Unit switch key (-/U button) to cycle through m³ → Ft³ → In³.
The meter will remember the last used measuring unit when switched on again.
4. Change Measurement Mode
The default measurement mode is Single Measurement. To switch between modes:
- Short press the Function key/Sound key (speaker icon button) to cycle through the following modes:
- Single Measurement
- Area Measurement
- Volume Measurement
- Single Pythagorean Theorem Measurement
- Dual Pythagorean Theorem Measurement
- Historical Data Review
5. Single Measurement
To measure a single distance:
- Ensure the device is in Single Measurement Mode.
- Aim the laser point at the target surface.
- Short press the Power/Measure key (orange button).
- The measuring result will be displayed immediately on the screen.
Image: Illustration of a single measurement being taken, showing the laser beam extending to a wall and the distance 'A' being measured.
6. Continuous Measurement (Max/Min)
To perform continuous measurement:
- Ensure the device is in Single Measurement Mode.
- Long press the Power/Measure key (orange button).
- Move the device to measure different points. The screen will display the maximum, minimum, and current measuring values.
Image: Display showing Max, Min, and Current values during continuous measurement, with a visual representation of the device moving to capture different distances.
7. Area Measurement
To calculate area:
- Switch to Area Measurement Mode using the Function key/Sound key.
- Aim the laser at the target and short press the Power/Measure key to measure the first side (length).
- Repeat for the second side (width).
- The calculated area will be displayed on the screen.
Image: Illustration of how to perform an area survey, showing the laser measuring length and width to automatically calculate the area.
8. Volume Measurement
To calculate volume:
- Switch to Volume Measurement Mode using the Function key/Sound key.
- Aim the laser at the target and short press the Power/Measure key to measure the length.
- Repeat for the width.
- Repeat for the height.
- The calculated volume will be displayed. (Note: Due to screen limitations, only two measured lengths are displayed at a time, but the volume calculation uses all three.)
Image: Illustration of how to perform volume measurement, showing the laser measuring length, width, and height for calculation.
9. Pythagorean Theorem Measurement (Single & Dual)
To measure indirect heights using the Pythagorean theorem:
- Single Pythagorean Theorem: Switch to this mode. Measure the hypotenuse and one right-angle side. The height will be calculated.
- Dual Pythagorean Theorem: Switch to this mode. Measure the right-angle side and two hypotenuses (from different points). The total height will be calculated.
Image: Diagram explaining Pythagorean Theorem Plus Measurement, where the device measures horizontally (b) and diagonally (a and c) to determine height (h).
Image: Diagram illustrating a standard Pythagorean Theorem Measurement, showing how to measure base (a) and hypotenuse (b) to find height (h).
10. Historical Data Review and Delete
The device can store up to 20 groups of measurement data.
- To review: In Historical Data Review Mode, short press Plus key/Reference switch key (+/d button) to view forward, or Minus key/Unit switch key (-/U button) to view backward.
- To delete: Short press the Clear/Exit/OFF key (C/O button) to delete measurements one by one.
Image: The device display showing multiple lines of data, indicating its ability to store and recall up to 20 groups of measurements.
11. Plus and Minus Functions
This function allows you to add or subtract measurements.
- In Single Measurement Mode, take a first measurement.
- Short press the Plus key/Reference switch key (+/d button) for addition, or Minus key/Unit switch key (-/U button) for subtraction.
- Take a second measurement. The sum or difference will be displayed.
- This function is also available in Area and Volume Measurement Modes.
12. Silence Function
To toggle the buzzer sound:
- Long press the Function key/Sound key (speaker icon button) to switch the buzzer on or off.
Maintenance
Cleaning and Care
- To clean the lens, use a soft, dry cloth.
- DO NOT clean the lens using alcohol or any other organic solvent.
- DO NOT wipe the lens directly with fingers or other rough surfaces.
- Store the device within the specified storage temperature range (-20°C to +65°C).
Forbidden Actions
- Opening or repairing the equipment without authorization.
- Measuring directly on the sun.
- Measuring outside the appointed range of the device.
- Immersing the equipment in water.
- Powering the equipment beyond the rated DC voltage.
Troubleshooting
Error Codes and Remedies
| Code | Possible Cause | Remedy |
|---|---|---|
| Err 10 | Battery too low | Change batteries. |
| Err 15 | Out of measuring range | Measure target within the specified range. |
| Err 16 | Received signal too weak | Measure a high reflectance target or use a high reflectance reflector. |
| Err 18 | Received signal too strong | Measure a low reflectance target or use a low reflectance reflector. |
| Err 26 | Value is too big to display at screen | Reduce measuring range. |
Battery Power Indication
When the battery icon on the display indicates low power, it's time to change the batteries to ensure accurate operation.
Specifications
| Feature | Specification |
|---|---|
| Product Name | DK Series Laser Distance Meter |
| Model/Range | DK40: 0.05m~40m DK60: 0.05m~60m DK80: 0.05m~80m DK100: 0.05m~100m DK120: 0.05m~120m |
| Measurement Accuracy (Standard Deviation) | ±2.0mm (± 1/16 inch) |
| Distance Unit | m, ft, in |
| Area Unit | m², ft², in² |
| Volume Unit | m³, ft³, in³ |
| Laser Type | 620-690nm |
| Laser Class | Class II (<1mW) |
| Single Measurement Time | 0.25s |
| Operating Temperature | 0°C ~ +40°C |
| Storage Temperature | -20°C ~ +65°C |
| Battery Type | AAA (Alkaline), 2×1.5V |
| Battery Count (Working Time) | >5000 times (fully charged) |
| Weight (no batteries) | Approximate 72g - 75g |
| Size (L*W*H) | 110mm × 50mm × 26mm |
| Historical Data Record | 20 Groups |
| Laser Auto On/Off | 30s |
| Instrument Auto Switch Off | 180s |
| Certification | CE, FCC, RoHS, KC, WEEE |
Image: A table summarizing the product specifications, including model ranges, accuracy, units, laser type, operating conditions, battery details, and dimensions.
Measurement Accuracy Notes
- When measuring distance within 10m, measurement accuracy is ±2mm.
- For distances more than 10m, measurement accuracy is calculated as: ±2mm ± 0.05% * (D-10), where D is the Measuring Distance in meters.
- Deviation may occur when measuring poorly reflecting targets, very rough surfaces, or in environments with extreme temperatures or very bright ambient light (e.g., direct sunlight).
User Tips
- Always ensure fresh batteries are installed for optimal performance and to avoid 'Err 10' messages.
- For measurements over long distances or in bright conditions, consider using a reflective target to improve accuracy and prevent 'Err 16' (weak signal).
- When performing continuous measurements, move the device slowly and steadily to capture accurate Max/Min values.
- Remember to check the measurement reference point (front or rear of the device) before taking critical measurements, especially for tight spaces.
Warranty & Support
Warranty Information
We guarantee a ONE-year warranty for the laser distance meter, starting from the purchase date. The warranty covers faulty equipment and allows for repair, replacement of defective parts, or replacement with an identical flawless product at our discretion.
Conditions NOT Included in Warranty:
- Opening the equipment with tools without specific permission.
- Use of the equipment outside the specified limits or improper handling.
- Use of non-original accessories.
- Servicing by unauthorized persons or workshops.
- Obliterated Serial Number of the equipment.
To claim warranty service, the warranty card must be provided along with your invoice.
Repairing and replacing equipment must comply with the 'Conditional Of Warranty' of manufacture.
For a digital copy of the user manual, please refer to the User manual (PDF).