JHao Xin BMW 3 Series GT F34 (2016-2019 LOW)

Contents

DRL Lamp Installation and Operation Manual

For BMW 3 Series GT F34 (2016-2019 LOW)

1. Product Overview

This manual provides instructions for the installation and operation of the JHao Xin Daytime Running Light (DRL) Light Guide Strip, designed as a 1:1 replacement for original car lights.

Product Name: Daytime Running Light (DRL) Light Guide Strip

Applicable Vehicle: For BMW 3 Series GT F34 2016-2019 LOW Front Headlights

This high-quality product is finely crafted to perfectly match and replace the original DRL components.

Video: Product overview and demonstration of the DRL Lamp components and their appearance.

2. Safety Information

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.

3. Package Contents

The package typically includes the following components:

  • DRL Light Guide Strips (Left and/or Right, or a Pair)
  • DRL CHIP Circuit Boards (LED driver modules)
DRL Lamp components including light guide strips and circuit boards, with a BMW headlight in the foreground.

Image: Main product view showing DRL light guide strips, DRL chips, and a car headlight.

Set of DRL light guide strips and multiple DRL circuit boards.

Image: A complete set of DRL light guide strips and their corresponding circuit boards.

Close-up of two DRL circuit boards (chips) with connectors.

Image: Detailed view of the DRL CHIP circuit boards.

4. Specifications

AttributeValue
Brand NameJHao Xin
Item TypeAngel Eyes
OriginMainland China
Package Length32 cm
Package Width22 cm
Package Height10 cm
Package Weight0.405 kg

5. Setup and Installation

5.1. Tools Preparation

  • Heat gun / oven
  • Flat-head screwdriver, plastic pry tools
  • Gloves, microfiber towel
  • Headlight sealant (butyl rubber is highly recommended)
  • Electrical tape / heat-shrink tubing
  • 12V power supply or car battery (for testing)

5.2. Standard Installation Procedure

  1. Remove the headlight assembly:
    • Open the hood.
    • Remove the headlight mounting screws (usually 2-4).
    • Unplug the headlight connector.
    • Place the headlight on a soft cloth to avoid scratches.
  2. Open the headlight lens (critical step):
    • Method A: Oven (most stable)
      • Preheat oven to 90°C - 150°C.
      • Heat the headlight for 8-12 minutes.
      • Wear gloves and gently pry the lens open with plastic pry tools.
    • Method B: Heat gun
      • Heat evenly around the sealant.
      • Pry while heating; do not focus on one spot to avoid burning the lens.
      • Rule: Pry only when the sealant is soft, do not force it.
  3. Remove the old guide light:
    • Locate the original DRL guide light / angel eyes.
    • Unplug the LED driver connector.
    • Release retaining clips / screws.
    • Carefully take out the old guide light.
  4. Install the new guide light:
    • Insert the new guide light into the original position.
    • Secure the clips to ensure no movement.
    • Connect the LED driver module.
  5. Cleaning and resealing:
    • Clean off all old sealant completely.
    • Apply a new ring of butyl rubber sealant in the groove.
    • Close the lens and press firmly.
    • Heat for another 30 seconds to fully melt the sealant.
    • Wipe off any dust inside the lens.
  6. Reinstall on the vehicle:
    • Reinstall the headlight assembly.
    • Plug in the headlight connector securely.
Top-down view of a car indicating Left (L) and Right (R) sides for component placement.

Image: Diagram indicating Left (L) and Right (R) sides of a vehicle for correct component orientation.

DRL light guide strip for the left side of the headlight, with a DRL chip.

Image: Example of a 2pcs Left CHIP DRL component.

A pair of DRL light guide strips and two DRL chips.

Image: Example of an A Pair DRL CHIP component.

6. Operation

6.1. Power-on Test

  • Turn the ignition on: The DRL lights should illuminate.
  • Turn the headlights on: The DRL lights should dim (this is normal operation).

7. Maintenance

Regularly inspect your DRL lamps for any signs of damage or wear. Keep the headlight lens clean to ensure optimal light output. If any issues arise, refer to the troubleshooting section.

8. Troubleshooting

  • No lighting or fault codes: If the DRLs do not light up or trigger fault codes after installation, computer coding may be required. This is common for certain vehicle models like Mercedes-Benz and BMW.
  • Headlight Yellowing:
    • 90% of cases: Headlight yellowing is often caused by long-term use of the DRL, where the ballast light source emits strong white light. Replacing only the DRL light guide strip can fix this issue (the DRL ballast chip does not need replacement in this scenario).
    • 10% of cases: Yellowing occurs due to DRL ballast damage, resulting in no strong light output. Check for signs of burning around the ballast light. If the ballast is damaged, both the ballast and the DRL light guide strip must be replaced.
  • Recommendation for complete resolution: To fully resolve headlight yellowing and brightness issues, it is recommended to directly replace both the ballast chip and the DRL light guide strip simultaneously.

9. User Tips

When diagnosing headlight yellowing or brightness issues, carefully identify the faulty component (DRL light guide strip or DRL ballast) to ensure effective replacement. Replacing both the ballast chip and DRL simultaneously is recommended for a complete resolution to avoid recurring problems.

10. Warranty and Support

For support or warranty inquiries, please contact the manufacturer or authorized representative:

  • Manufacturer/Importer:
    Yiwu Xinyu Trading Co., Ltd.
    Room 503, No. 22 Liuruitang Road, Choujiang Street,
    Yiwu City, Jinhua City, Zhejiang Province, Postal Code: 330782
    Email: 51281048@qq.com
  • EU Authorized Representative:
    MJCM SARL .0033
    752907452.78 Avenue des Champs-Élysées Office 326.
    Email: mjcm190928@gmail.com

A PDF version of the user manual is available for download: User manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.