1. Introduction
Thank you for purchasing the LIDESENS Dimmable 3W Slim LED Cabinet Light. This product is designed for versatile lighting solutions in various applications, including RVs, campers, motorhomes, cupboards, and other areas with limited height clearance. Its ultra-slim design and low power consumption make it an efficient and practical choice. Please read this manual carefully before installation and use to ensure proper operation and safety.
2. Safety Warnings and Precautions
- WARNING: BE CAREFUL OF HIGH TEMPERATURE! Although LED lights are more efficient, the light fixture may still become hot during operation.
- Always turn off the power supply to the installation area before attempting any installation, maintenance, or troubleshooting.
- Ensure that your power source is a stable DC 12V. Using an incorrect voltage will cause the light to operate dimly or fail completely.
- Do not touch the light fixture immediately after it has been working or just switched off, as it may still be hot. Allow it to cool down before handling.
- This product is designed for indoor use or protected environments (e.g., inside RVs, cabinets). Do not expose to direct water or extreme weather conditions unless specifically rated for outdoor use.
- Installation should be performed by a qualified individual if you are unsure about electrical wiring.
3. Specifications
| Feature | Specification |
|---|---|
| Brand Name | LIDESENS |
| Model | LDS-CL-70 |
| Product Name | LED Cabinet Light |
| Power | 3W LED |
| Voltage | DC 12V |
| Color Temperature (CCT) | Warm White (2700-3000K), Natural White (4000-4500K) |
| Dimensions (Diameter x Height) | φ70mm × H14mm (2.76in × 0.55in) |
| Cutout Hole Diameter | φ55-60mm (2.17-2.36in) |
| Beam Angle | 120° |
| Cable Length | 30cm (11.8in) |
| Luminous Flux | 240-300 Lumens |
| Color Rendering Index (CRI) | >Ra 80 |
| Service Life | 50,000 hours |
| Certification | CE |
| Origin | Mainland China |
| Installation Method | Recessed Assembly |
4. Installation Instructions
These LED cabinet lights are designed for recessed installation. Free cable connectors are provided for easy setup.
- Prepare the Installation Area: Ensure the power supply to the area where you intend to install the lights is completely turned off.
- Mark and Cut the Hole: Using the specified cutout diameter (φ55-60mm or approximately 2-1/4 inches), mark the desired location for each light. Carefully cut the holes in the ceiling or cabinet surface.
- Connect Wiring: The lights operate on DC 12V. Connect the red wire from the light to the positive (+) terminal of your 12V DC power supply and the black wire to the negative (-) terminal. Use the provided cable connectors for a secure connection. Ensure all connections are tight and insulated.
- Insert the Light: Gently push the LED light into the cutout hole. The spring clips on the sides of the light will hold it securely in place.
- Test the Lights: Once all lights are installed and wired, restore power to the circuit and test the functionality of the lights.
5. Operating Instructions
These LED cabinet lights are designed for simple operation with a 12V DC power source. They are dimmable, allowing you to adjust the light intensity if connected to a compatible 12V DC dimmer switch (not included).
- Turning On/Off: Control the lights using the main power switch connected to your 12V DC circuit.
- Dimming (Optional): If you have installed a compatible 12V DC dimmer switch, use the dimmer to adjust the brightness of the lights to your preferred level.
6. Care and Maintenance
- Cleaning: To clean the light fixture, ensure the power is off and the light has cooled down. Wipe gently with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Inspection: Periodically check the wiring and connections for any signs of wear, damage, or loose connections.
- Replacement: LED lights have a long lifespan and typically do not require bulb replacement. If the light fails, the entire unit may need to be replaced.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on |
|
|
| Light is dim or flickers |
|
|
| Light gets too hot |
|
|
8. User Tips
No specific user tips were available from reviews or Q&A for this product at this time. However, general tips for LED cabinet lights include:
- Consider the color temperature (Warm White, Natural White) based on the ambiance you want to create. Warm White is often preferred for cozy spaces, while Natural White is good for task lighting.
- For RV and solar-powered setups, ensure your 12V DC system can handle the cumulative wattage of all installed lights.
- If installing multiple lights, plan your wiring path carefully to minimize visible cables and ensure even power distribution.
9. Warranty and Support
This product comes with a 1-year warranty for quality issues. We will repair it free of charge within this period. The returning shipping costs for warranty repairs should be paid by our factory.
If you have any questions, concerns, or require technical assistance, please contact us:
- Email: sales@lidesens.com
- Whatsapp: +0086-18033449799
We aim to reply to all inquiries within 24 hours.
For a comprehensive guide, you may refer to the official user manual PDF: View User Manual (PDF)