Aninerel ANL-11000T-48L-W-PRO

Contents

Aninerel 11KW 48V Dual MPPT Hybrid Solar Inverter User Manual

Model: ANL-11000T-48L-W-PRO

1. About This Manual

1.1. Purpose

This manual describes the assembly, installation, operation, and troubleshooting of this unit. Please read this manual carefully before installations and operations. Keep this manual for future reference.

1.2. Scope

This manual provides safety and installation guidelines as well as information on tools and wiring.

2. Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  2. CAUTION – To reduce risk of injury, charge only deep-cycle lead acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
  3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  4. To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  5. CAUTION – Only qualified personnel can install this device with battery.
  6. NEVER charge a frozen battery.
  7. For optimum operation of this inverter/charger, please follow required spec to select appropriate cable size. It's very important to correctly operate this inverter/charger.
  8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  9. Please strictly follow installation procedure when you want to disconnect AC or DC terminals. Please refer to the INSTALLATION section of this manual for the details.
  10. Fuse is provided as over-current protection for the battery supply.
  11. GROUNDING INSTRUCTIONS - This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulation to install this inverter.
  12. NEVER cause AC output and DC input short circuited. Do NOT connect to the mains when DC input short circuits.
  13. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this inverter/charger back to local dealer or service center for maintenance.

3. Introduction

This is a multi-function inverter/charger, combining functions of inverter, MPPT solar charger and battery charger to offer uninterruptible power support with portable size. Its comprehensive LCD display offers user-configurable and easy-accessible button operation such as battery charging current, AC/solar charger priority, and acceptable input voltage based on different applications.

3.1. Features

  • Pure sine wave inverter
  • Inverter running without battery
  • Built-in MPPT solar controller
  • Configurable input voltage range for home appliances and personal computers via LCD setting
  • Configurable battery charging current based on applications via LCD setting
  • Configurable AC/Solar Charger priority via LCD setting
  • Compatible to mains voltage or generator power
  • Auto restart while AC is recovering
  • Overload/ Over temperature/ short circuit protection
  • Smart battery charger design for optimized battery performance
  • Cold start function

3.2. Basic System Architecture

The following illustration shows basic application for this inverter/charger. It also includes following devices to have a complete running system:

  1. Generator or Utility.
  2. PV modules (option)

Consult with your system integrator for other possible system architectures depending on your requirements.

This inverter can power all kinds of appliances in home or office environment, including motor-type appliances such as tube light, fan, refrigerator and air conditioner.

Application Diagram of Aninerel Hybrid Solar Inverter
Figure 1: Hybrid Power System Application Diagram. Shows connections from Solar Panel, Utility Grid, Generator, and Battery to the inverter, which then powers various Home Appliances like TV/Computer, Air conditioner, Refrigerator/Washing machine.
Pure Sine Wave Inverter output comparison
Pure Sine Wave Inverter: Provides clean, stable power similar to household grid power, reducing noise and interference, protecting electrical components, and ensuring stable operation for various devices.

4. Product Overview

Aninerel 11KW Hybrid Solar Inverter Front View with Features
Front view of the Aninerel 11KW Hybrid Solar Inverter, highlighting features like 11KW 48V 160A, Hybrid Solar Inverter, Dual MPPT, WiFi, RGB Lights, Dual MPPT, PV 60-500Vdc, Colored LCD, BMS, Lithium Battery Activation, Dual Outputs, No Battery Mode.
Aninerel 11KW Hybrid Solar Inverter Rear Panel Layout
Rear panel layout of the inverter. Key components include: 1. LCD display, 2. RGB Indicator, 3. Function buttons, 4. Power on/off switch, 5. Battery negative/positive outlet hole, 6. RS232 communication port (RJ45), 7. RS485 communication port (RJ45), 8. RS232 communication port (DB9), 9. Dry contact port, 10. PV1 input, 11. PV2 input, 12. AC input, 13. Grounding, 14. Main output, 15. Second output. Note: RS232 communication port (DB9) and RS232 communication port (RJ45) cannot be used simultaneously.

5. Installation

5.1. Unpacking and Inspection

Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. You should have received the following items inside of package:

  1. The unit x 1
  2. User manual x 1
  3. PV connector x 4
  4. Battery fuse x 1 (Only 11K model)

The product is well-packaged with foam protection to keep the unit safe during shipping.

Video: Unboxing and initial inspection of the Aninerel 11KW Hybrid Solar Inverter, showing the packaging and included accessories.

5.2. Preparation

Before connecting all wirings, please take off the bottom cover by removing four screws.

5.3. Mounting the Unit

Consider the following points before selecting where to install:

  1. Do not mount the inverter on flammable construction materials.
  2. Mount on a solid surface.
  3. Install this inverter at eye level in order to allow the LCD display to be read at all times.
  4. The ambient temperature should be between 0°C and 55°C to ensure optimal operation.
  5. The recommended installation position is to be adhered to the wall vertically.
  6. Be sure to keep other objects and surfaces as shown in the right diagram to guarantee sufficient heat dissipation and to have enough space for removing wires.

SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

Inverter Mounting Dimensions and Clearance
Diagram showing recommended mounting dimensions (56.4mm, 290.0mm, 361.4mm, 495.0mm) and clearances (20cm side, 50cm top/bottom) for proper heat dissipation.

5.4. Battery Connection

CAUTION: For safety operation and regulation compliance, it's requested to install a separate DC over-current protector or disconnect device between battery and inverter. It may not be requested to have a disconnect device in some applications, however, it's still requested to have over-current protection installed. Please refer to typical amperage in below table as required fuse or breaker size.

WARNING! All wiring must be performed by a qualified personnel.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for battery connection. To reduce risk of injury, please use the proper recommended cable.

ModelMaximum AmperageBattery CapacityWire SizeCable mm²Terminal Size (mm) L x W x DTorque Value
8.5KVA180A400AH4AWG*22537 x 22 x 8.410~12 Nm
11.0KVA220A600AH2AWG*23837 x 22 x 8.410~12 Nm

Battery Connection Steps:

  1. Make positive and negative cables based on recommended terminal size.
  2. Connect all battery packs as units require. It's suggested to use recommended battery capacity.
  3. Insert battery cable flatly into battery connector of inverter and make sure the bolts are tightened with torque of 10-12Nm. Make sure polarity at both the battery and the inverter/charge is correctly connected and battery cables are tightly screwed to the battery connector.
Battery Connection Diagram for 48V Model
Diagram illustrating the series connection of four 12V batteries for a 48V system. Ensure correct polarity when connecting to the inverter.

5.5. AC Input/Output Connection

CAUTION: Before connecting to AC input power source, please install a separate AC breaker between inverter and AC input power source. This will ensure the inverter can be securely disconnected during maintenance and fully protected from over current of AC input. The recommended spec of AC breaker is 63A.

CAUTION: There are two terminal blocks with "IN" and "OUT" markings. Please do NOT mis-connect input and output connectors.

WARNING! All wiring must be performed by qualified personnel.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for AC input connection. To reduce risk of injury, please use the proper recommended cable size as below.

Suggested Cable Requirement for AC Wires:

ModelGaugeTorque Value
All Model6 AWG1.2~1.4Nm

AC Input/Output Connection Steps:

  1. Before making AC input/output connection, be sure to open DC protector or disconnector first.
  2. Remove insulation sleeve 10mm for six conductors. And shorten phase L and neutral conductor N 3 mm.
  3. Insert AC input wires according to polarities indicated on terminal block and tighten the terminal screws. Be sure to connect PE protective conductor (yellow-green) first.
    • →Ground (yellow-green)
    • L→LINE (brown or black)
    • N→Neutral (blue)

WARNING: Be sure that AC power source is disconnected before attempting to hardwire it to the unit.

  1. Then, insert AC output wires according to polarities indicated on terminal block and tighten terminal screws. Be sure to connect PE protective conductor (yellow-green) first.
    • →Ground (yellow-green)
    • L→LINE (brown or black)
    • N→Neutral (blue)
  2. Make sure the wires are securely connected.

CAUTION: Important Be sure to connect AC wires with correct polarity. If L and N wires are connected reversely, it may cause utility short-circuited when these inverters are worked in dual output operation.

CAUTION: Appliances such as air conditioner are required at least 2~3 minutes to restart because it's required to have enough time to balance refrigerant gas inside of circuits. If a power shortage occurs and recovers in a short time, it will cause damage to your connected appliances. To prevent this kind of damage, please check manufacturer of air conditioner if it's equipped with time-delay function before installation. Otherwise, this inverter/charger will trig overload fault and cut off output to protect your appliance but sometimes it still causes internal damage to the air conditioner.

Video: Step-by-step demonstration of wiring the battery terminals to the inverter and powering it on, showing the LCD display activating.

5.6. PV Connection

CAUTION: Before connecting to PV modules, please install separately a DC circuit breaker between inverter and PV modules.

WARNING! All wiring must be performed by qualified personnel.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for PV module connection. To reduce risk of injury, please use the proper recommended cable size as below.

Suggested Cable Requirement for PV Wires:

ModelTypical AmperageCable SizeTorque
All Model18A*210 AWG1.4~1.6 Nm

PV Module Selection:

When selecting proper PV modules, please be sure to consider below parameters:

  1. Open circuit Voltage (Voc) of PV modules not exceeds max. PV array open circuit voltage of inverter.
  2. Open circuit Voltage (Voc) of PV modules should be higher than min. battery voltage.

Solar Charging Mode Specifications:

INVERTER MODEL8.5KVA11.0KVA
Max. PV Array Open Circuit Voltage500VDC
PV Array MPPT Voltage Range60VDC~500VDC
Max. PV INPUT CURRENT18A*2

Take the 450Wp and 550Wp PV module as an example. After considering above two parameters, the recommended module configurations are listed in the table below. The recommended module configurations are fit for PV1 or PV2; for example: PV1 is 8 pcs in serial and PV1 could be 8 pcs in serial too, total quantity of panels is 16pcs.

Solar Panel Configuration Examples:

Solar Panel Spec. (reference)SOLAR INPUTQ'ty of panelsTotal input powerInverter Model
450Wp
Vmp: 34.67Vdc
Imp: 13.82A
Voc: 41.25Vdc
Isc: 12.98A
3 pcs in serial3 pcs1,350 WAll Model
4 pcs in serial4 pcs1,800 W
5 pcs in serial5 pcs2,250 W
6 pcs in serial6 pcs2,700 W
7 pcs in serial7 pcs3,150 W
8 pcs in serial8 pcs3,600 W
450Wp (continued)9 pcs in serial9 pcs4,050 WAll Model
10 pcs in serial10 pcs4,500 W
11 pcs in serial11 pcs4,950 W
12 pcs in serial12 pcs5,400 W
550Wp
Vmp: 42.48Vdc
Imp: 12.95A
Voc: 50.32Vdc
Isc: 13.70A
3 pcs in serial3 pcs1,650 WAll Model
4 pcs in serial4 pcs2,200 W
5 pcs in serial5 pcs2,750 W
6 pcs in serial6 pcs3,300 W
7 pcs in serial7 pcs3,850 W
8 pcs in serial8 pcs4,400 W
9 pcs in serial9 pcs4,950 W

PV Module Wire Connection Steps:

  1. Remove insulation sleeve 10 mm for positive and negative conductors.
  2. Check correct polarity of connection cable from PV modules and PV input connectors. Then, connect positive pole (+) of connection cable to positive pole (+) of PV input connector. Connect negative pole (-) of connection cable to negative pole (-) of PV input connector.
  3. Make sure the wires are securely connected.
PV Connection Diagram and Specifications
Diagram illustrating PV connection with wire sizes (4-6mm²) and terminal types (Female/Male). Also includes a table of PV parameters for inverter model ANL-11000T-48L-W, including Rated Power (11000W), Max. PV Array Open Circuit Voltage (500VDC), and Max. charging Current (PV) (160A).

6. Final Assembly

After connecting all wirings, please put the bottom cover back by screwing four screws.

7. Operation

7.1. Power ON/OFF

Once the unit has been properly installed and the batteries are connected well, simply press the On/Off switch (located on the bottom of the case) to turn on the unit.

7.2. Operation and Display Panel

The operation and display panel, shown below, is on the front panel of the inverter. It includes three indicators, four function keys, and an LCD display, indicating the operating status and input/output power information.

Inverter Front Panel with LCD and Buttons
Front panel of the inverter showing the LCD display, RGB indicator, and function buttons (ESC, UP, DOWN, ENTER).

RGB Indicator (Default)

ModeColorStatusMessages
Inverter modeGreenSolid OnOutput is powered by battery or PV in battery mode
Battery is fully charged or isn't charged.
FlashingBattery is charging with 2s-on and 1s-off
AC modeBlueSolid OnOutput is powered by AC or PV in AC mode
Battery is fully charged or isn't charged
FlashingBattery is charging with 2s-on and 1s-off
Standby modeCyanSolid OnBattery is fully charged or isn't charged
FlashingBattery is charging with 2s-on and 1s-off
Fault modeRedSolid OnFault occurs in the inverter.
Bypass modePurpleSolid OnWorking in AC mode without charging
Charging modeYellowSolid OnBattery is fully charged, when switch is off
FlashingBattery is charging, when switch is off

Function Keys:

Function KeyDescription
ESCTo exit setting mode
UPTo go to previous selection
DOWNTo go to next selection
ENTERTo confirm the selection in setting mode or enter setting mode

7.3. LCD Display

The LCD display information will be switched in turns by pressing keys. All of information could be shown in 1/2/3/4/5 area of LCD.

LCD Display Explanation:

  • **Area 1:** Shows PV data, such as PV voltage/current/power.
  • **Area 2:** Shows battery data, such as battery voltage/current/power/SOC.
  • **Area 3:** Shows AC-output data, such as output voltage/current/power/percentage/frequency.
  • **Area 4:** Shows AC-input data, such as input voltage/current/power/percentage/frequency.
  • **Area 5:** Shows setting program code/Eco/buzzer/error/warning.
  • **Area 6:** Shows power generation/time/date.

LCD Data Polling Display Mode:

  • **Simultaneously polling data:** Press "UP" or "DOWN" button to show all data from area-1 to area-4 simultaneously and all dates will be updated with pressing. Press the ESC key to return the initial data.
  • **Independent polling data:** Data of area 1-4 could be polling displayed independently as follows:
    1. Press "Enter" key, circle icon of area 1 will be flashing, press "UP" or "DOWN" to display data of area 1.
    2. Continue to press "Enter" key, circle icon of area 2 will be flashing, press "UP" or "DOWN" to display data of area 2.
    3. Continue to press "Enter" key, circle icon of area 3 will be flashing, press "UP" or "DOWN" to display data of area 3.
    4. Continue to press "Enter" key, circle icon of area 4 will be flashing, press "UP" or "DOWN" to display data of area 4.
    5. Continue to press "Enter" key, circle icon of area 1 will be flashing, it would come back to area 1.

LCD Setting Display:

After pressing and holding "Enter" key for 3 seconds, the unit will enter setting mode. Press "UP" or "DOWN" button to select setting programs. And then, press "ENTER" button to confirm the selection or ESC button to exit. When the unit enters setting mode the LCD display shows:

  • **Area 5:** Setting program code.
  • **Area 6:** Setting program meaning.
  • **Area 1:** Setting minimum value, if the setting program has minimum value.
  • **Area 4:** Setting maximum value, if the setting program has maximum value.
  • **Area 2:** Setting program item.
  • **Area 3:** Setting current value which could be set.

Other Display:

Please press and hold the key "Down" for a long time on the main menu page, you could see the following information in area 6:

  1. Software Version;
  2. Model code Version;
  3. CPU type;
  4. Hardware Version;

7.4. LCD Setting Programs (F0-F4)

The inverter offers extensive configuration options via the LCD display. Here's an overview of the setting groups:

F0: Setting General Parameters

ProgramDescriptionSelectable Option
01AC input voltage rangeAppliances (default): 90-280VAC
UPS: 170-280VAC
Generator: 170-280VAC (Note: Generators may cause unstable output)
02Power saving mode enable/disableDisabled: Inverter output not affected by low/high load.
Enabled: Inverter output off when connected load is low.
03Overload bypassBypass disable (default): Unit transfers to line mode if overload occurs in battery mode.
Bypass enable: Unit transfers to line mode if overload occurs in battery mode.
04Auto restart when overload occursRestart disable
Restart enable (default)
05Auto restart when over temperature occursRestart disable
Restart enable (default)
06Auto bypassManual (default)
Auto: Automatically bypasses if mains power is normal.
07Auto return to default display screenReturn to default display screen (default): Returns after 1 minute of inactivity.
Stay at latest screen: Display remains on last screen.
08Backlight controlBacklight on
Backlight off (default)
09Buzzer modeMode1 (Buzzer mute)
Mode2 (Buzzer sounds on input source change/warning/fault)
Mode3 (Buzzer sounds on specific warning/fault)
Mode4 (default) (Buzzer sounds on fault)
10Modbus ID SettingRange: 001 (default)~247
16Dry contact modeModel1 (default): Deliver signal to external device when battery voltage reaches warning level.
Model2: Allow neutral and grounding of AC output to be connected together (only when inverter works with external grounding box in battery mode).

F1: Setting AC Output Parameters

ProgramDescriptionSelectable Option
01Output source prioritySUB priority (default): Solar->Utility->Battery. Solar energy charges first, then powers loads.
SBU priority: Solar->Battery->Utility. Solar energy powers loads first, then charges battery.
SUF priority: Solar->Utility->Battery. Solar energy powers loads first, then charges battery, then feeds to grid.
02AC output modeSingle: This inverter is used in single phase application.
03Output voltage230V (default). Available settings: 220V, 230V, 240V.
04Output frequency50Hz (default). Available settings: 50Hz and 60Hz.
06Slave output source priorityOFF (default): Turn off slave output source priority.
SUB, SBU, SUF: Same function as program 01 of F1.

F2: Setting Battery Parameters

ProgramDescriptionSelectable Option
01Battery typeAGM (default)
Flooded
User-Defined (allows setting charge voltage and low DC cut-off voltage)
PYLON US2000 Protocol (3.5 Version)
Standard communication Protocol 2
LIB (Lithium battery default values)
16Bulk charging time (C.V stage)Automatically (default): Inverter judges charging time automatically.
5 min to 900 min (increment of 5 min).
17Battery equalizationBattery equalization enable/disable (default).
18Battery equalization voltageDefault 58.4V. Range: floating voltage (program 04 of F2) ~ 62V.
19Battery equalized time60min (default). Range: 0min to 900min (increment of 5min).
20Battery equalized timeout120min (default). Range: 0min to 900min (increment of 5min).
21Equalization interval30 days (default). Range: 1 to 90 days (increment of 1 day).
22Equalization activated immediatelyEnable/Disable (default).
23Manual activate the lithium battery settingActive/Disable (default).
24Automatic activation for lithium batteryAuto/Disable (default).
25Max battery discharge current settingOFF (default). Range: 50 to 500.
26Lithium battery activation time6s (default). Range: 6s~300s.

F3: Setting Time Parameters

ProgramDescriptionSelectable Option
01Date settingSet the machine date (year, month, day)
02Time settingSet the machine time (hours, minutes)

F4: Setting Systems Parameters

ProgramDescriptionSelectable Option
01Reset all stored data of PV generated power and output load energyReserve data (default)
Reset generated energy data
02RGB mode - Checking RGB Indicator tableMode 1 (Default): RGB LED working normally.
Mode 2: RGB LED working with only unit in fault mode.
Mode 3: RGB LED always OFF.
Mode 4: RGB LED shows as model 1 and whether battery is fully charged or not, RGB LED won't be flashing.
Mode 5: RGB LED shows as model 1 and whether battery is fully charged or not, RGB LED will be flashing.
03RGB brightness adjustmentAdjust brightness of RGB within 30% to 100%.
04RGB Light Color selection in inverter ModeRed, Green, Blue, Cyan, Purple, Yellow, White, Pale cyan, Pale yellow, Pale blue, Pink.

8. Battery Equalization

Equalization function is added into the charge controller. It reverses the buildup of negative chemical effects like stratification, a condition where acid concentration is greater at the bottom of the battery than at the top. Equalization also helps to remove sulfate crystals that might have built up on the plates. If left unchecked, this condition, called sulfation, will reduce the overall capacity of the battery. Therefore, it's recommended to equalize battery periodically.

8.1. How to Apply Equalization Function

You must enable battery equalization function in monitoring LCD setting program 17 of F2 first. Then, you may apply this function in device by either one of following methods:

  1. Setting equalization interval in program 21 of F2.
  2. Active equalization immediately in program 22 of F2.

8.2. When to Equalize

In float stage, when the setting equalization interval (battery equalization cycle) is arrived, or equalization is active immediately, the controller will start to enter Equalize stage.

Battery Charging Curve with Equalization
Diagram showing the battery charging curve stages: Bulk, Absorption, Float, and Equalize. The Equalize stage is triggered when the equalization interval is met or activated manually.

8.3. Equalize Charging Time and Timeout

In Equalize stage, the controller will supply power to charge battery as much as possible until battery voltage raises to battery equalization voltage. Then, constant-voltage regulation is applied to maintain battery voltage at the battery equalization voltage. The battery will remain in the Equalize stage until setting battery equalized time is arrived.

However, in Equalize stage, when battery equalized time is expired and battery voltage doesn't rise to battery equalization voltage point, the charge controller will extend the battery equalized time until battery voltage achieves battery equalization voltage. If battery voltage is still lower than battery equalization voltage when battery equalized timeout setting is over, the charge controller will stop equalization and return to float stage.

9. Setting for Lithium Battery

9.1. Lithium Battery Connection

If choosing lithium battery for the inverter, you are allowed to use the lithium battery only which we have configured. There are two connectors on the lithium battery: RS485 port of BMS and power cable.

Please follow below steps to implement lithium battery connection:

  1. Assemble battery terminal based on recommended battery cable and terminal size (same as Lead acid, see section Lead-acid Battery connection for details).
  2. Connect the end of RS485 port of battery to BMS(RS485) communication port of inverter.

9.2. Lithium Battery Communication and Setting

If choosing a lithium battery, make sure to connect the BMS communication cable between the battery and the inverter. This communication cable delivers information and signals between the lithium battery and the inverter. This information is listed below:

  • Re-configure charging voltage, charging current, and battery discharge cut-off voltage according to the lithium battery parameters.
  • Have the inverter start or stop charging according to the status of the lithium battery.

Connect the end of RS485 of battery to RS485 communication port of inverter

Make sure the lithium battery RS485 port connects to the inverter is Pin to Pin, the communication cable is inside of package and the inverter RS485 port pin assignment shown as below:

Pin numberRS485 Port
PIN1RS485-B
PIN2RS485-A
PIN7RS485-A
PIN8RS485-B

9.3. Setting for PYLON US2000 Lithium Battery

PYLONTECH US2000 Lithium Battery Setting:

Dip Switch: There are 4 Dip Switches that set different baud rate and battery group address. If switch position is turned to the "OFF" position, it means "0". If switch position is turned to the "ON" position, it means "1".

  • Dip 1 is "ON" to represent the baud rate 9600.
  • Dip 2, 3 and 4 are reserved for battery group address.
  • Dip switch 2, 3 and 4 on master battery (first battery) are to set up or change the group address.

NOTE: "1" is upper position and "0" is bottom position.

Process of Install:

  1. Use the RS485 cable to connect inverter and Lithium battery.
  2. Switch on Lithium battery.
  3. Press more than three seconds to start Lithium battery, power output ready.
  4. Turn on the inverter.
  5. Be sure to select battery type as "Li2" in LCD program 5. If communication between the inverter and battery is successful, the battery icon on the LCD display will light up.

9.4. Setting for Lithium Battery Without Communication

This suggestion is used for lithium battery application and to avoid lithium battery BMS protection without communication. Please finish the setting as follows:

A. Recommended method 1: Set battery type as "LIB" in program 01 of F2;

B. Recommended method 2: Setting as follows:

  1. Before starting setting, you must get the battery BMS specification:
    • Max charging voltage
    • Max charging current
    • Discharging protection voltage
  2. Set battery type as "LIB" in program 01 of F2;
  3. Set C.V voltage as Max charging voltage of BMS-0.5V in program 03 of F2;
  4. Set floating charging voltage as C.V voltage in program 03 of F2;
  5. Set Low DC cut-off voltage ≥ discharging protection voltage of BMS+3V;
  6. Set Max charging current in program 09 of F2 which must be less than the Max charging current of BMS.
  7. Setting voltage point back to utility source when selecting "SBU priority" in program 05 of F2.

The setting value must be ≥Low DC cut-off voltage+2V, or else the inverter will have a warning as battery voltage low.

Remark:

  1. You'd better to finish setting without turn on the inverter (just let the LCD show, no output);
  2. When you finish setting, please restart the inverter.

10. Specifications

10.1. Table 1 Line Mode Specifications

INVERTER MODEL8.5KVA11.0KVA
Input Voltage WaveformSinusoidal (utility or generator)
Nominal Input Voltage230Vac
Low Loss Voltage170Vac±7V (UPS)
90Vac±7V (Appliances)
170Vac±7V (UPS)
90Vac±7V (Appliances)
Low Loss Return Voltage180Vac±7V (UPS)
100Vac±7V (Appliances)
180Vac±7V (UPS)
100Vac±7V (Appliances)
High Loss Voltage280Vac±7V
High Loss Return Voltage270Vac±7V
Max AC Input Voltage300Vac
Nominal Input Frequency50Hz / 60Hz (Auto detection)
Low Loss Frequency40±1Hz
Low Loss Return Frequency42±1Hz
High Loss Frequency65±1Hz
High Loss Return Frequency63±1Hz
Output Short Circuit ProtectionBattery mode: Electronic Circuits
Efficiency (Line Mode)>95% (Rated R load, battery full charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)

Output Power Derating:

When AC input voltage drops to 95V or 170V depending on models, the output power will be derated.

When battery voltage drops to 50.5V (8.5K) / 55.0V (11K), the output power will be derated.

10.2. Table 2 Inverter Mode Specifications

INVERTER MODEL8.5KVA11.0KVA
Rated Output Power8.5KVA/8.5KW11.0KVA/11.0KW
Dual output functionYes
Max. main output power8.5KVA/8.5KW11.0KVA/11.0KW
Max. second output power5.0KVA/5.0KW5.5KVA/5.5KW
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation230Vac±5%
Output Frequency60Hz or 50Hz
Peak Efficiency94%
Overload Protection5.5s@≥140% load; 10.5s@100%~140% load
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage48Vdc
Cold Start Voltage46.0Vdc
Low DC Warning Voltage (Just for AGM and Flooded)@ load < 20%: 44.0Vdc
@ 20% ≤ load < 50%: 42.8Vdc
@ load ≥ 50%: 40.4Vdc
Low DC Warning Return Voltage (Just for AGM and Flooded)@ load < 20%: 46.0Vdc
@ 20% ≤ load < 50%: 44.8Vdc
@ load ≥ 50%: 42.4Vdc
Low DC Cut-off Voltage (Just for AGM and Flooded)@ load < 20%: 42.0Vdc
@ 20% ≤ load < 50%: 40.8Vdc
@ load ≥ 50%: 38.4Vdc

10.3. Table 3 Charge Mode Specifications (Utility Charging Mode)

INVERTER MODEL8.5KVA11.0KVA
Charging Current (Max) (AC+PV)140Amp160Amp
AC Charging Current (Max)120Amp (@ VI/P=230Vac)
Bulk Charging Voltage (Flooded Battery)58.4Vdc
Bulk Charging Voltage (AGM / Gel Battery)56.4Vdc
Floating Charging Voltage54Vdc
Overcharge Protection63Vdc
Charging Algorithm3-Step

10.4. Table 3 Charge Mode Specifications (Solar Input)

INVERTER MODEL8.5KVA11.0KVA
Rated Power5000W*25500W*2
Max. PV Array Open Circuit Voltage500Vdc
PV Array MPPT Voltage Range60Vdc~500Vdc
Max. MPPT Charge Current140A160A
Max. Input Current18A*2

10.5. Table 4 General Specifications

INVERTER MODEL8.5KVA11.0KVA
Safety CertificationCE
Operating Temperature Range-10°C to 55°C
Storage temperature-15°C~60°C
Humidity5% to 95% Relative Humidity (Non-condensing)
Dimension (D*W*H), mm540x403x122
Net Weight, kg14.414.8

11. Warning Indicator

There are seven groups about warning code, a warning code consists of group code and number, number is first and group code is last, such as OC.

  • A: Inverter group fault code
  • B: Battery group fault code
  • C: PV group fault code
  • D: Output group fault code
  • E: Parallel group fault code
  • F: Other group fault code
  • G: Grid group fault code

Warning Code Table:

Warning CodeWarning EventAudible AlarmIcon flashing
0BBattery lowBeep once every second0B
1BBattery is not connectedNone1B
2BBattery equalizationNone2B
3BBattery low and it isn't up to the setting value of program 06 of F2 groupBeep twice every 3 seconds3B
4BLithium battery communication is abnormalBeep once every 0.5 second4B
5BBattery discharge overcurrentNone5B
1CPV energy is too weakBeep twice every 3 seconds1C
0DOverloadBeep once every 0.5 second0D
1DOutput power deratingBeep twice every 3 seconds1D
3DThe load exceeds the set value of program 12 of F1None3D
0FTemperature is too HighBeep three times every second0F

12. Troubleshooting

12.1. Fault Reference Code

There are seven groups about fault code, a fault code consists of group code and number, group code is first and number is last, such as C0.

  • A: Inverter group fault code
  • B: Battery group fault code
  • C: PV group fault code
  • D: Output group fault code
  • E: Parallel group fault code
  • F: Other group fault code
  • G: Grid group fault code

Fault Code Table:

Fault CodeFault EventIcon on
A0Output short circuited.A0
A1Output voltage is too high.A1
A2Over current or surgeA2
A3Over DC voltage in AC outputA3
A4Inverter current offset is too highA4
A5Output voltage is too lowA5
A6Inverter negative powerA6
B0Battery voltage is too highB0
B1DCDC over currentB1
B2DC/DC current offset is too highB2
C0PV over currentC0
C1PV over voltageC1
C2PV1 current offset is too highC2
C3PV2 current offset is too highC3
D0Overload time outD0
D1Op current offset is too highD1
D2Op2 current offset is too highD2
F0Over temperature of inverter moduleF0
F1Over temperature of PV moduleF1
F2Over temperature of DCDC moduleF2
F3Bus voltage is too highF3
F4Bus soft start failedF4
F5Bus voltage is too lowF5
F6Hardware incompatibilityF6
F7Screen communication abnormalityF7

12.2. Troubleshooting Table

ProblemLCD/LED/BuzzerExplanation / Possible causeWhat to do
Unit shuts down automatically during startup process.LCD/LEDs and buzzer will be active for 3 seconds and then complete off.The battery voltage is too low1. Re-charge battery.
2. Replace battery.
No response after power on.No indication.1. The battery voltage is far too low.
2. Battery polarity is connected reversed.
1. Check if batteries and the wiring are connected well.
2. Re-charge battery.
3. Replace battery.
Mains exist but the unit works in battery mode.Input voltage is displayed as 0 on the LCD and green LED is flashing.Input protector is trippedCheck if AC breaker is tripped and AC wiring is connected well.
Green LED is flashing.Insufficient quality of AC power. (Shore or Generator)1. Check if AC wires are too thin and/or too long.
2. Check if generator (if applied) is working well or if input voltage range setting is correct. (UPS / Appliance)
Change output source priority to Utility first.
When the unit is turned on, internal relay is switched on and off repeatedly.Green LED is flashing.Set "SBU" or "SUB" as the priority of output source.Change output source priority to Utility first.
LCD display and LEDs are flashingBattery is disconnected.Check if battery wires are connected well.
Buzzer beeps continuously and red LED is on.Fault code D0Overload error. The inverter is overload 100% and time is up.Reduce the connected load by switching off some equipment.
Fault code A2Output short circuited.Check if wiring is connected well and remove abnormal load.
Fault code F2Internal temperature of inverter component is over 100°C.Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Fault code B0Battery is over-charged.Return to repair center.
Fault code B0The battery voltage is too high.Check if spec and quantity of batteries are meet requirements.
Other issues.Fault code A1/A5Output abnormal (Inverter voltage below than 190Vac or is higher than 260Vac)1. Reduce the connected load.
2. Return to repair center.
Fault code F3/F4Internal components failed.Return to repair center.
Fault code A2, F5, A3Over current or surge.
Bus voltage is too low.
Output voltage is unbalanced.
Restart the unit, if the error happens again, please return to repair center.
Another fault codeIf the wires are connected well, please return to repair center.

13. User Tips

  • For optimal performance, ensure all wiring connections are secure and follow the recommended cable sizes to prevent energy loss and ensure safety.
  • Regularly monitor the LCD display for system data and any warning indicators to catch potential issues early.
  • When setting up for lithium batteries, carefully follow the communication and dip switch settings to ensure proper integration and battery management.
  • If using a generator as an AC input source, be aware that its unstable output might affect the inverter's stability. Consider adjusting AC input voltage range settings accordingly.
  • For appliances with motors, like air conditioners, allow sufficient restart time (2-3 minutes) after power interruptions to prevent damage.

14. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your local dealer or authorized service center. Only qualified service personnel should attempt repairs.

© 2024 Aninerel. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.