Honda Rear Shock Absorber Dust Cover Top Screw Cap

Contents

Honda Rear Shock Absorber Dust Cover Top Screw Cap Instruction Manual

For Honda Accord, Avancier, Inspire, CR-V, Breeze (2019-2025)

1. Introduction

This manual provides essential information for the proper installation and maintenance of your new Honda Rear Shock Absorber Dust Cover Top Screw Cap. Please read all instructions carefully before proceeding with installation to ensure safety and optimal performance.

Honda Rear Shock Absorber Dust Cover Top Screw Cap

Figure 1: Rear Shock Absorber Dust Cover Top Screw Cap

Video 1: Product Overview

2. Compatibility Check

To ensure the purchased accessory is compatible with your vehicle, it is crucial to verify the Vehicle Identification Number (VIN) and Original Equipment (OE) number. The auto parts are confirmed and shipped based on these numbers.

2.1 Vehicle Identification Number (VIN)

The VIN is a unique identifier for your vehicle and can be found in several locations:

  • Lower left corner of the front windshield (driver's side).
  • Left side of the dashboard.
  • Inside the engine compartment.
  • On the door frame (driver's side).
  • On vehicle registration documents.
Example of VIN on vehicle document

Figure 2: Example of VIN on a vehicle document (Russian registration certificate)

2.2 Original Equipment (OE) Number

The OE number is typically located on the back of the product accessory itself and consists of numbers and letters. This number helps confirm the exact part specification.

Example of OE number on a cable

Figure 3: Example of OE number on a cable (Part number: 6305300XST02A, QCN72BAJGW, HW:P2KM62-2)

Example of OE number on a module

Figure 4: Example of OE number on a module (Part number: 30G 713 033H, SW 0054, HW 007)

Important: It is highly recommended to provide your VIN/chassis number to the seller for a precise compatibility check before installation. Incorrect parts may not fit or function properly.

3. Safety Information

WARNING: We recommend that a certified technician install this system. Professional knowledge of disassembly/reassembly procedures and post-installation checks are essential. Attempting installation without this knowledge and expertise may jeopardize the integrity and/or operation of the vehicle.

  • Always wear safety glasses when performing vehicle maintenance.
  • Ensure the vehicle is securely supported on a level surface using a jack and jack stands before working underneath.
  • Do not add, alter, or fabricate any factory or aftermarket parts that increase vehicle height beyond the intended design. Mixing component brands or combining different lift types (body lift with suspension lift) voids all warranties.
  • Be aware that modifying vehicle height can affect handling characteristics. Always drive cautiously after any suspension modifications.
  • Braking performance and capabilities may decrease when significantly larger/heavier tires and wheels are used. Consider speedometer recalibration if larger tires are installed.
  • Read all instructions thoroughly before beginning installation. Verify all kit hardware against the parts list. If any parts are missing, do not proceed with installation; contact customer service.

4. Components and Tools

4.1 Packing List

  • 1 pc Rear Shock Absorber Dust Cover Top Screw Cap

4.2 Required Tools

Qty Tool
1Floor Jack
2Jack stands
1Torque Wrench
1Safety Glasses
19/16" Wrench/Socket
113mm Wrench/Socket
115mm Wrench/Socket
117mm Wrench/Socket
119mm Wrench/Socket
16mm Allen Wrench
11/4" Allen Wrench

4.3 Required Miscellaneous Items

  • OE Service Manual (recommended)
  • Grease (optional)
  • Loctite (Red) (optional)

4.4 Torque Specifications

The following torque values are general guidelines. Specific applications may vary. Always consult your vehicle's service manual for precise torque specifications.

SAE Fasteners Size Grade 5 (ft/lbs) Grade 8 (ft/lbs)
5/161520
3/83035
7/164560
1/26590
9/1695130
5/8135175
3/4185280
Metric Fasteners Size Class 8.8 (ft/lbs) Class 10.9 (ft/lbs)
659
81823
103245
125575
1485120
16130165
18170240

5. Installation Guide

This section outlines the general procedure for replacing a rear shock absorber dust cover. Due to the critical nature of suspension components, professional installation is highly recommended. Always refer to your vehicle's specific service manual for detailed instructions.

Exploded view diagram of rear shock absorber assembly

Figure 5: Exploded view of Rear Shock Absorber Assembly. Part 3 is the Rear Shock Absorber Dust Cover.

  1. Park the vehicle on a level, solid surface (e.g., concrete or asphalt).
  2. Secure the vehicle from rolling by engaging the parking brake and placing wheel blocks.
  3. Jack up the rear of the vehicle and support it with jack stands under the vehicle frame. Ensure the vehicle is stable.
  4. Locate the rear shock absorber assembly. The dust cover (Part 3 in Figure 5) is typically found at the top of the shock absorber.
  5. Carefully remove any components obstructing access to the dust cover and top screw cap. This may involve removing the wheel, and potentially other suspension components depending on your vehicle model.
  6. Remove the old dust cover and top screw cap. Note their orientation for reassembly.
  7. Clean the area around the shock absorber shaft and mounting points.
  8. Install the new Rear Shock Absorber Dust Cover and Top Screw Cap. Ensure they are correctly seated.
  9. Reinstall any removed components, tightening all fasteners to the torque specifications found in your vehicle's service manual or the general guidelines provided in Section 4.4.
  10. Lower the vehicle carefully.
  11. Perform a visual inspection to ensure all components are correctly installed and secured.
Installed suspension component view

Figure 6: General view of an installed suspension component. The dust cover is part of this assembly.

6. Maintenance

The rear shock absorber dust cover protects the shock absorber shaft from dirt, debris, and moisture, extending its lifespan. Regular inspection is key to maintaining its effectiveness.

  • Visual Inspection: Periodically check the dust cover for cracks, tears, or signs of wear. Inspect for any accumulation of dirt or debris around the shock absorber shaft.
  • Cleaning: If dirt or mud accumulates, gently clean the dust cover and surrounding area with water and a mild detergent. Avoid high-pressure washing directly on the dust cover to prevent damage.
  • Replacement: Replace the dust cover immediately if any damage is observed to prevent premature wear of the shock absorber.

7. Troubleshooting

If you encounter any issues after installation, consider the following:

  • Loose Fit: Ensure the dust cover is correctly seated and the top screw cap is tightened to specification. Recheck all fasteners.
  • Unusual Noises: If you hear new noises from the suspension, re-verify all installation steps and torque settings. A loose component can cause rattling or clunking.
  • Visible Damage: If the dust cover appears damaged shortly after installation, it might indicate an installation error or a defective part. Inspect for proper clearance with other components.

For persistent issues, consult a certified automotive technician.

8. Specifications

Attribute Value
Product NameRear Shock Absorber Dust Cover Top Screw Cap
BrandHonda (Compatible)
MaterialNot specified (typically rubber or plastic)
OriginMainland China
CompatibilityHonda Accord, Avancier, Inspire, CR-V, Breeze (2019-2025 models)
Package Dimensions (Approx.)8cm x 8cm x 8cm
Package Weight (Approx.)0.1 kg

9. User Tips

  • Always double-check compatibility with your specific vehicle model and year using VIN and OE numbers before purchasing and installing.
  • Consider replacing both left and right dust covers simultaneously for balanced wear and consistent protection.
  • When working on suspension, ensure all components are clean to prevent dirt from entering critical areas.

10. Frequently Asked Questions (FAQ)

Q: Is professional installation required?
A: While not strictly required, professional installation is highly recommended due to the safety-critical nature of suspension components and the need for specific tools and torque settings.
Q: How do I find my VIN?
A: Your VIN can typically be found on your vehicle's dashboard (driver's side, near the windshield), on the driver's side door jamb, or on your vehicle registration documents.
Q: What is the purpose of the dust cover?
A: The dust cover protects the shock absorber shaft from road debris, dirt, and moisture, which can cause corrosion and premature wear of the shock absorber's seals and internal components.

11. Additional Resources

A detailed user manual in PDF format is available for further reference:

  • User manual (PDF): Refer to the official product page or contact customer support for the direct download link. (e.g., View User Manual (PDF))

© 2023 Honda. All rights reserved. This manual is for informational purposes only.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.