VGETTING XFF500030

Contents

XFF500030 Rear Bumper Light User Manual

Model: XFF500030 | Brand: VGETTING

Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your VGETTING XFF500030 Rear Bumper Light. Please read all instructions carefully before use.

The VGETTING XFF500030 Rear Bumper Light is designed for specific Land Rover models, offering enhanced visibility and a modern aesthetic. It features a durable ABS housing, PC lens, and LED chips for long-lasting performance.

Safety & Warnings

Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture during installation or if not properly sealed.

Product Features

  • Durable and Sturdy: High-quality ABS lamp housing and PC lens, resistant to impact, UV rays, and good weather resistance.
  • Waterproof and Dustproof: Sealed design with an IP67 rating, ensuring reliable operation in various environments.
  • Original Factory Appearance: Perfectly fits the bumper lines. Red/smoke lens design, maintaining the original Land Rover texture.
  • Ultra Long Lifespan: LED chips have a lifespan of over 30,000 hours and are maintenance-free.
Waterproof bumper lights in various weather conditions
Figure 1: Waterproof and dustproof design, adapting to rainy, foggy, snowy, and dusty conditions.

Compatibility

This rear bumper light is compatible with the following vehicle models:

  • Land Rover Discovery 3 LR3 (2005-2009)
  • Land Rover Discovery 4 LR4 (2010-2013)
  • Land Rover Range Rover Sport (L320 facelift) (2010-2013)

Setup and Installation

Step 1: Preparation Work (Safety First)

  1. Power Off: Park the car steadily and engage the handbrake.
  2. Disconnect Battery: Be sure to disconnect the negative cable of the battery to prevent electrical hazards.

Step 2: Removing the Old Light

  1. Access: Open the tailgate.
  2. Locate Cover: Find and remove the tail light repair cover from the inside of the vehicle.
  3. Disconnect: Disconnect the electrical plug.
  4. Unscrew: Unscrew the fixing nut.
  5. Remove Lamp: Carefully pull out the old lamp from the outside to the inside.

Step 3: Installing the New Light

  1. Pre-testing:
    • Connect the new light plug to the original car harness.
    • Reconnect the battery.
    • Turn on the power and test whether the brake lights, turn signals, reverse lights, and driving lights are all lit up normally.
  2. Formal Fixing:
    • After confirming that the function is normal, disconnect the battery again.
    • Align the new light with its position and install it.
    • Tighten all the fixing nuts from the inside.
    • Finally, tighten the electrical plug and replace the maintenance cover.
Wiring diagram for bumper light installation
Figure 2: Easy Installation Wiring Diagram. Connect the white wire to the running light, black wire to negative, red wire to the brake light, and yellow wire to the turn signal.
Before and after installation of bumper lights on a Land Rover
Figure 3: Visual comparison of the vehicle's rear bumper before and after the light installation.

Operating Modes

The VGETTING XFF500030 Rear Bumper Light supports multiple lighting functions:

  • Running Light: Provides continuous illumination when the vehicle's lights are on.
  • Brake Light: Illuminates brighter when the brake pedal is pressed.
  • Turn Signal Light: Features dynamic flowing amber light for turn indications.
  • Start-up Animation: A brief light sequence upon vehicle ignition.
Video 1: Demonstration of the bumper light's start-up animation, driving light, turn signal light, and brake light functions.
Bumper light showing running light, brake light, and dynamic flowing turn signal
Figure 4: Visual representation of the running light, brake light, and dynamic flowing turn signal in operation.

Maintenance

Final Inspection and Sealing

  1. Function Review: After installation, reconnect the battery and perform a final check of all lighting functions.
  2. Sealing Inspection: After washing the car or exposing it to water, check for any severe water ingress or fogging inside the lamp. Slight fogging is normal and should clear up as the lamp heats up and dries. If severe water ingress occurs, re-check the installation and sealing.

Troubleshooting

No specific troubleshooting steps are provided in the available documentation. If you encounter issues, please verify the wiring connections according to the installation diagram and ensure the battery is properly connected. If problems persist, contact customer support.

Specifications

Attribute Value
Product Name Rear Bumper Lights Assembly
Model XFF500030, XFF500020 (OEM NO.)
Brand Name VGETTING
Material ABS shell + PC transparent lens
Voltage DC 12V
Lumens 800Lm
Waterproof Rating IP67
Certification CCC
High-concerned chemical None
Color Red (available in Red and Smoke lens options)
Origin Mainland China
Package Length (approx.) 25 cm
Package Width (approx.) 7 cm
Package Height (approx.) 7 cm
Package Weight (approx.) 0.5 kg
Product details showing PC lens, bright light, and ABS housing
Figure 5: Detailed view of the product components: PC Lens, Bright Light, and ABS Housing.
Style B red bumper light
Figure 6: Example of Style B Red bumper light.

User Tips

Based on general user feedback for similar products:

  • Ensure all wiring connections are secure and properly insulated to prevent short circuits and water damage.
  • Double-check vehicle compatibility before purchasing and installation.
  • Consider professional installation if you are not comfortable with automotive electrical work.

Warranty and Support

This product is manufactured by Guangzhou Camel Technology Co., Ltd. and holds CCC certification, with an Attestation of Compliance (CE Certification) as per the provided documentation. The information in this manual is derived from the official product documentation.

For product support, warranty claims, or technical assistance, please contact the manufacturer or their authorized representative:

  • Manufacturer: Guangzhou Camel Technology Co., Ltd.
  • Manufacturer Address: No. 4 West Fangxin Road, Fangcun Avenue, Liwan District, Guangzhou City, Guangdong Province.
  • Manufacturer Email: 1620477595@qq.com
  • EU Authorized Representative: MJCM SAR
  • EU Representative Address: 78 avenue des Champs Elysees Bureau 326, PARIS.FR
  • EU Representative Email: mjcm190928@gmail.com
  • EU Representative Contact Number: 0033 752907452

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.