Digital Thickness Gauge Digital Thickness Gauge

Contents

Portable Digital Thickness Gauge User Manual

Model: Digital Thickness Gauge

A portable digital thickness gauge designed for precise measurement of various materials such as paper, leather, film, and metal sheets. Features a clear digital display, thumb-press operation, and unit switching between millimeters and inches.

1. Product Overview

The Digital Thickness Gauge is a precision instrument designed for quick and accurate measurement of material thickness. Its compact design and digital display make it easy to use for a variety of applications.

Portable Digital Thickness Gauge
Figure 1: Portable Digital Thickness Gauge

Key Components

Diagram of Digital Thickness Gauge components
Figure 2: Labeled Diagram of Gauge Components
  • Press Type Measuring Rod: Applies pressure to the material for measurement.
  • Liquid Crystal Box (Display): Shows the measurement readings.
  • Inch/mm Key: Toggles between inch and millimeter units.
  • OFF/ON Key: Powers the device on or off.
  • ZERO Key: Resets the display to zero.
  • Measuring Head: The contact point for measurement.

2. Setup

2.1 Battery Installation

The device requires a 1.5V button battery (SR44/LR44). Ensure the battery is installed correctly before use.

  1. Locate the battery compartment cover on the back of the gauge.
  2. Gently open the cover.
  3. Insert a new 1.5V SR44/LR44 button battery, ensuring the correct polarity (+/-).
  4. Close the battery compartment cover securely.
Battery compartment of the thickness gauge
Figure 3: Battery Compartment (requires 1.5V SR44/LR44 battery)

2.2 Initial Preparation

  1. Remove all protective packaging materials from the equipment.
  2. Inspect the product for any visible damage.
  3. Press the 'OFF/ON' button to power on the device.
  4. Ensure the measuring surfaces are clean and free from dust or debris.
  5. With the measuring head and anvil closed (no material between them), press the 'ZERO' button to set the display to 0.00. This calibrates the gauge for accurate measurements.

3. Operating Instructions

This digital thickness gauge is designed for measuring the thickness of various materials up to 12.7mm (0.5 inches).

  1. Power On: Press the 'OFF/ON' button to turn on the gauge.
  2. Zeroing: Before each measurement, especially if the gauge has been moved or if you suspect a change in calibration, ensure the measuring head and anvil are closed and press the 'ZERO' button to reset the display to 0.00.
  3. Select Units: Press the 'inch/mm' button to switch between millimeter (mm) and inch (in) units as desired.
  4. Measure Material: Gently lift the press-type measuring rod using your thumb. Place the material to be measured between the measuring head and the anvil. Release the measuring rod slowly so that the measuring head rests on the material.
  5. Read Measurement: The thickness reading will be displayed on the Liquid Crystal Box.
  6. Power Off: After use, press the 'OFF/ON' button to turn off the device to conserve battery life.
Digital Thickness Gauge measuring a sheet of material
Figure 4: Gauge in use, measuring a thin sheet

4. Maintenance

4.1 Cleaning

  • Wipe the gauge with a soft, dry cloth.
  • Do not use abrasive cleaners or solvents, as these can damage the display or the plastic housing.
  • Keep the measuring surfaces clean and free of dust or debris to ensure accurate readings.

4.2 Storage

  • Store the device in a dry place, away from direct sunlight and extreme temperatures.
  • Keep away from children.
  • If storing for an extended period, it is recommended to remove the battery to prevent leakage.
Digital Thickness Gauge with its protective case
Figure 5: Product stored in its protective case

5. Troubleshooting

  • Display not showing readings: Check if the battery is correctly installed and has sufficient charge. Replace the battery if necessary.
  • Inaccurate readings: Ensure the measuring surfaces are clean. Perform a zero-calibration before taking measurements. Avoid applying excessive force during measurement.
  • Buttons unresponsive: Try replacing the battery. If the issue persists, contact customer support.

6. Specifications

FeatureSpecification
Measurement Range0-12.7mm / 0-0.5 inches
Resolution0.01mm / 0.0005 inches
Power Supply1.5V Button Battery (SR44/LR44)
Battery IncludedNo
MaterialPlastic
Dimensions (L x W x H)Approx. 16cm x 9cm x 3cm
WeightApprox. 0.219 kg
OriginMainland China

7. User Tips

  • Always perform a zero-calibration before taking critical measurements to ensure accuracy.
  • For consistent results, apply gentle and consistent pressure when taking measurements.
  • Keep the gauge away from strong magnetic fields, which can affect its electronic components and accuracy.
  • When measuring soft materials, be careful not to compress the material excessively, which could lead to inaccurate readings.

8. Warranty and Support

For warranty information or technical support, please contact the seller or retailer from whom you purchased this product. Please retain your proof of purchase for any warranty claims.

A PDF user manual may be available from the seller for additional details.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.