IKSLED AC-7036-T

Contents

IKSLED AC-7036-T Wave Activated Sensor Switch User Manual

Model: AC-7036-T

1. Product Introduction

This is a 100-240V AC touchless wave-activated sensor switch, designed for cabinets, closets, mirror cabinets, and more. It allows you to turn lights on or off with a simple hand wave, offering convenient, hygienic control ideal for situations where direct contact is not desired or convenient.

IKSLED AC-7036-T Wave Activated Sensor Switch main unit and sensor probe
Figure 1: IKSLED AC-7036-T Wave Activated Sensor Switch

2. Specifications

Feature Detail
Model Number AC-7036-T
Brand Name IKSLED
Product Name Wave Activated Sensor Switch
Working Voltage AC 100-240V, 50/60Hz
Control Method Wave-activated touchless control
Max Load Power 400W (supports up to 3 lamps simultaneously)
Sensor Probe Size 10mm diameter, 12mm height
Main Unit Size 76mm x 36mm x 23mm
Control Logic Wave once to turn on, wave again to turn off
Material Plastic
Certifications CE, RoHS, EMC, LVD
Hole Size 10mm
Function Gesture control to turn the light on and off
Installation Hidden / flush mount
EU LVD Voltage High voltage: Above 50Vac or 75Vdc
High-concerned chemical None
Product dimensions of the sensor probe and main control unit
Figure 2: Product Dimensions (Sensor Probe: 10mm diameter, 12mm height; Main Unit: 70mm x 35mm x 23mm)

3. Installation Instructions

  1. Always disconnect the power supply before installation. Never work with live wires to avoid electric shock.
  2. Install the sensor probe at the preset location (e.g., cabinet edge, inside mirror cabinet). The 10mm diameter probe fits standard mounting holes, ideal for areas easily accessible by hand.
  3. Connect the wires according to the connection diagram:
    • Power Input: Connect the live wire (L) and neutral wire (N) to the "Li" and "Ni" terminals of the main unit respectively.
    • Load Output: Connect the live wire and neutral wire of the lamp/device to the "Lo" and "No" terminals of the main unit respectively.
  4. After confirming all connections are correct, turn on the power to use the device.
Wiring diagram for the AC-7036-T sensor switch, showing connections for input power and various lamp types.
Figure 3: Connection Diagram for LED, energy-saving lamps, and 12V/24V lamps.

4. Operation Guide

  1. The device enters standby mode automatically after power-on.
  2. Wave your hand in front of the sensor probe to turn the light on. Wave again to turn it off.
  3. The sensor offers stable detection; a clear hand wave is sufficient to trigger the control without touching the device.
Video 1: Demonstration of hand wave control to turn the light on and off.

5. Applicable Loads

  • Direct Control: 100-240V AC devices (such as LED lamps, energy-saving lamps, fans, etc.)
  • Indirect Control: Control DC12V/24V low-voltage lamps (e.g., light strips) via a constant voltage adapter.
Image showing various compatible loads for the sensor switch, including light bars, LED lights, exhaust fans, water pumps, and high power lamps.
Figure 4: Compatible Loads (Do Not Overpower)

6. Safety Precautions

  1. Both the sensor probe and main unit carry high voltage. Disconnect the power during installation and removal. Do not operate with live power.
  2. Do not disassemble the housing or touch the internal circuit board directly to prevent electric shock.
  3. Do not exceed the maximum load power of 400W to avoid equipment damage.
  4. Install the sensor away from strong direct light and electromagnetic interference to ensure stable performance.
Warning against disassembling the sensor cable, indicating high voltage.
Figure 5: Safety Warning: Do not disassemble or operate with live power.

7. Maintenance

To ensure optimal performance and longevity of your sensor switch, follow these simple maintenance guidelines:

  • Keep the sensor probe clean and free from dust or debris. Use a soft, dry cloth for cleaning.
  • Avoid spraying liquids directly onto the sensor or main unit.
  • Ensure the area around the sensor is clear of obstructions that might interfere with its detection.

8. Troubleshooting

  • Device not responding to hand waves:
    • Check if the power supply is connected correctly and the device is receiving power.
    • Ensure the sensor probe is not obstructed and is clean.
    • Verify that the sensor is installed away from strong direct light or sources of electromagnetic interference.
    • Confirm that the hand wave gesture is clear and performed directly in front of the sensor.
  • Light flickers or does not turn on/off reliably:
    • Check the wiring connections to ensure they are secure and correct as per the diagram.
    • Ensure the total load power does not exceed the maximum 400W capacity of the switch.

9. User Tips

  • This sensor switch operates with a simple on/off toggle logic: one wave turns it on, another wave turns it off. It does not feature a timed auto-off function (e.g., turning off after 30 seconds).
  • For optimal performance, ensure the sensor is mounted in a location where hand gestures are natural and unobstructed.
  • Consider the aesthetic of your installation. The compact design and 10mm hole size allow for discreet, flush mounting in various furniture pieces.

10. Warranty and Support

This IKSLED AC-7036-T Wave Activated Sensor Switch comes with a 1-Year Warranty from the date of purchase.

For technical assistance, troubleshooting, or any inquiries regarding your product, please contact customer support. You may also reach out for customized consultation via WhatsApp: +8615289643001.

Please refer to the official AliExpress platform for detailed service terms and conditions.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.