1. Introduction
Thank you for choosing the VEKOOTO AHD 1080P Wide Angle Rear View Backup Camera. This camera is designed to enhance your driving safety by providing a clear, wide-angle view of the area behind your vehicle. Featuring AHD 1080P resolution, starlight night vision, and an IP69 waterproof rating, it is built for reliable performance in various conditions. This manual provides essential information for proper installation, operation, and maintenance.

Figure 1: VEKOOTO AHD 1080P Backup Camera
2. Safety Warnings
Please read and understand all safety warnings before installation and use to prevent injury or damage.
- Installation Warning (Electrical & Vehicle Safety): Disconnect the vehicle's negative battery terminal before installation. Route cables away from sharp edges, heat sources, and moving parts (e.g., pedals, steering column) to prevent short circuits, insulation damage, or interference with vehicle operation.
- Operational Warning (Driver Responsibility): The displayed image is an aid only and may not accurately represent distances or obstacles. Drivers are responsible for checking their surroundings while reversing. Do not rely solely on the camera system to detect small children, animals, or objects.
- Regulatory Warning (EU Compliance): This product must be installed according to the supplied manual. Improper use may lead to product malfunction. Do not dispose of this product with household waste.
- Caution: Vehicle Damage: Do not pull or stress the cable connectors with excessive force. When drilling holes for cable passthrough, check for existing wiring, fuel lines, or components behind the surface to avoid damage. Apply rust protection to any exposed metal on drilled holes.
3. Package Contents
Please check that all items are present in the package:
- 1x VEKOOTO AHD 1080P Rear View Camera
- 1x 4-Pin Video Cable (length varies by selection: 5m, 10m, 15m, 20m)
- 1x Instruction Manual
Video 1: Unboxing the VEKOOTO Backup Camera
4. Specifications
| Feature | Specification |
|---|---|
| Resolution | AHD 1080P (1920*1080 effective pixels) |
| Pixels | 2,000,000 pixels |
| Viewing Angle | 120° |
| Lens Material | Plastic + Glass |
| Shell Material | Aluminium alloy |
| Body Material | ABS |
| Night Vision | Starlight Night Vision, Infrared Night Vision |
| Waterproof Rating | IP69 |
| Connectivity | Wired (4-pin connector) |
| Cable Type | Coaxial / Multi-core |
| Operating Voltage | 12V DC (SELV) |
| Operating Temperature | -20°C to +70°C |
| Certification | CE, ECE R118 Compliant |
| Alarm Type | ACCESSORIES, Front, Front Side, Rear Side |

Figure 2: Product Dimensions (46mm x 60mm)
5. Setup and Installation
These instructions are generic. Refer to your vehicle's specific wiring diagram if available.
5.1 Pre-Installation Check
Before permanently installing the cable, temporarily connect the entire system (Camera → Cable → Monitor) to a 12V power source to verify functionality. Ensure the camera displays a clear image on your monitor.
5.2 Cable Routing
- Camera End: Start at the rear of the vehicle. Connect the 4-pin cable to the reverse camera.
- Routing to the Front: Carefully route the cable through the vehicle interior to the dashboard or monitor location.
- Use existing rubber grommets in the bodywork to pass the cable from the outside to the inside. If a new hole is drilled, use a waterproof grommet (if supplied) to protect the cable and seal the hole.
- Conceal the cable behind interior trim panels, ensuring it is not pinched or crushed.
- Monitor End: Route the remaining length of cable to the location of the display unit and connect it.
5.3 Interface Definition
The camera uses a standard 4-pin connector for video, audio, power, and ground connections.

Figure 3: 4-Pin Interface Definition for Camera and Host/Monitor
5.4 Compatibility
This camera is compatible with Furrion Pre-Wired RVs, allowing for easier integration into existing systems.

Figure 4: Camera installed on a Furrion Pre-Wired RV
6. Operation
Once correctly installed and the vehicle is started:
- The camera system activates automatically when the vehicle is engaged in reverse gear (powered by the reverse light circuit).
- The high-definition image will be transmitted via the video cable to your display unit.

Figure 5: Day and Night Vision Performance
7. Maintenance and Care
- Cleaning: Clean the connectors occasionally with a dry, soft cloth to prevent signal degradation. Do not use aggressive cleaning agents or solvents.
- Inspection: Periodically inspect the cable for signs of wear, cuts, or damage, especially where it passes through body panels or is exposed to the elements. Ensure the camera lens is clean for optimal image clarity.

Figure 6: Waterproof design for all climates
8. Troubleshooting
If you experience issues with your camera system, consider the following:
- No Image/Poor Image Quality: Ensure all 4-pin connections are secure and fully seated. Check the power supply to the camera and monitor. Verify that the monitor is set to the correct input source. Clean the camera lens if it appears dirty.
- Intermittent Signal: Inspect the entire length of the video cable for any kinks, cuts, or damage. Ensure the cable is not pinched by vehicle panels.
- Camera Not Activating: Confirm that the camera is correctly wired to the vehicle's reverse light circuit for automatic activation.
9. User Tips
- For optimal night vision performance, ensure your vehicle's reverse lights are functioning correctly.
- Regularly check the camera's mounting bracket to ensure it remains secure, especially after driving on rough terrain.
- When routing cables, use zip ties or cable clips to secure them neatly and prevent them from interfering with moving parts or getting damaged.
10. Warranty and Support
Manufacturer Information
Manufacturer: Dongguan Xiaodou Technology Co., Ltd.
Address: Room 1403, Building 3, Tianan Digital City, Fenggang Town, Dongguan City, Guangdong, China
EU Authorized Representative
Representative: PROCONSEIL FR
Address: 200 rue de la Croix Nivert, 75015, Paris, France