Suetlcoity Land Rover Discovery Sport L550

Contents

User Manual

Rear Windshield Wiper Trim

Brand: Suetlcoity | Model: Land Rover Discovery Sport L550 (2014-2019)

1. Product Overview

This car decoration accessory is designed to enhance your vehicle's aesthetic appeal while protecting vulnerable surfaces from scratches, dust, and minor impacts. The product features high-quality 3M adhesive tape for secure, long-lasting installation without damaging your car's original finish.

2. Installation Instructions

Important Notice: Some products may be OEM replacement parts requiring removal of original components before installation. Always confirm compatibility with your car model, year, configuration, and chassis code.

2.1 Preparation (Critical for Strong Adhesion)

Proper surface preparation ensures maximum bonding strength of the 3M adhesive tape.

  1. Choose a clean, dry, and well-ventilated area for installation. Avoid direct sunlight or humid environments.
  2. Clean the target surface thoroughly with an alcohol wipe (or 50-70% isopropyl alcohol solution) to remove all dust, grease, and fingerprints.
  3. Allow the cleaned surface to air-dry completely for 1-2 minutes. Do not wipe it dry.
  4. Ensure the installation temperature is between 15°C-35°C (59°F-95°F). Low temperatures can significantly reduce adhesive effectiveness.
Back of trim pieces showing 3M adhesive tape
Figure 1: Rear view of the trim pieces with pre-applied 3M adhesive tape.

2.2 Step-by-Step Installation

  1. Carefully peel off the red protective film from the 3M adhesive tape. Avoid touching the adhesive surface with bare fingers to maintain its bonding properties.
  2. Align the accessory precisely with your desired position on the vehicle.
  3. Press firmly on the entire surface of the accessory for at least 30 seconds. Apply a minimum pressure of 15 lbs (6.8 kg) to properly activate the adhesive.
  4. Do not move or remove the accessory within 24 hours after installation. This allows the adhesive to fully cure and achieve permanent bonding.
Easy installation steps for car trim
Figure 2: Visual guide for easy installation by tearing off the tape and pressing.
Installed rear wiper trim showing precise fit
Figure 3: The trim piece installed, demonstrating a precise match and fit to the original car design.

3. Functions & Benefits

3.1 Decoration Function

  • Enhances vehicle appearance with a stylish design.
  • Customizes your car to reflect personal taste without permanent modifications.

3.2 Protection Function

  • Shields car surfaces from scratches, scuffs, and minor collisions.
  • Prevents dust accumulation and simplifies cleaning (wipe with a damp cloth).
  • No tools, no drilling required, and removable without residue.
Rear wiper trim installed on Land Rover Discovery Sport
Figure 4: The rear wiper trim enhancing the vehicle's aesthetic.

4. Maintenance & Care

  • Clean the accessory regularly with a soft, damp cloth. Avoid using abrasive cleaners or solvents, as these can damage the finish.
  • Check the adhesion monthly. If any edges begin to lift, reapply pressure to secure them. Ensure the surface is clean before reapplying pressure.
  • For Removal: Use a 3M adhesive remover or gently heat the tape with a hair dryer (on low heat) to soften the bond. Then, peel off the accessory slowly and carefully.

5. Troubleshooting

Problem Solution
Accessory falls off
  1. Recheck surface cleanliness before installation.
  2. Ensure installation temperature was adequate (15°C-35°C).
  3. Apply more firm pressure during installation.
Adhesive residue left after removal Wipe with alcohol or a dedicated 3M adhesive remover.
Misalignment after installation
  • If within 5 minutes (before adhesive fully cures): Carefully remove and reposition.
  • If after 24 hours: Follow the general removal instructions (heat/adhesive remover) to prevent damage.

6. Specifications

MaterialPremium Grade ABS Plastic
ColorSilvery
Item TypeChromium Styling
Special FeaturesProtecting and Beautifying
External Testing CertificationISO9001
Applicable Model Year2014-2019
Package Dimensions (L x W x H)19 cm x 8 cm x 5 cm
Package Weight0.15 kg
Premium Grade ABS Plastic features
Figure 5: Features of the premium grade ABS plastic used in the product.

7. Safety Warnings

Warning!

  • Do not install this accessory on airbag deployment areas (e.g., steering wheel, door panels near airbags), as it may interfere with safety systems.
  • Avoid blocking the driver's view (e.g., front windshield, rearview mirrors) to comply with traffic safety regulations.
  • Keep this product away from children under 36 months, as small parts may pose choking hazards.
  • Do not use or install near open flames or high-temperature sources (above 60°C / 140°F), as the adhesive may weaken.

8. User Tips

  • For maximum longevity and adhesion, always ensure the installation surface is meticulously clean and dry before applying the trim.
  • Applying firm, even pressure across the entire surface during installation is crucial for activating the adhesive properly.
  • Allowing the full 24-hour curing time without disturbance will ensure the strongest possible bond.

9. Warranty & Support

9.1 After-Sales Support

After-sales service covers manufacturing defects (not improper use) within 15 days after signing for the product.

Contact Us:

  • AliExpress Store Link: Carcartrim Store
  • Customer Service Email: 2978746630@qq.com
  • Service Hours: 9:00 AM - 6:00 PM (GMT+8), Monday to Friday

9.2 Compliance Information

  • EU Representative: Apex CE Specialists GmbH
  • Representative Address: Grafenberger Allee 277, 40237 Düsseldorf, DE
  • Tel: 49-21312066043
  • E-mail: comInfo@apex-ce.de

Copyright © Carcartrim Store. All rights reserved. This manual is subject to change without prior notice. For the latest version, please visit our store.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.