Product Overview
This manual provides instructions for the installation, operation, and maintenance of your new 12V Lighter Power Outlet Socket and its dedicated removal tool. This product is designed as a direct replacement for original faulty or worn cigarette lighter sockets in compatible vehicles.
Video: Overview of the 12V Power Outlet Socket and Removal Tool.
Setup and Installation
Safety Preparation & Tools Required
- Tools Needed: Included dedicated socket removal tool, clean cloth, protective gloves.
- Safety Precautions:
- Park vehicle on flat ground, turn off engine completely.
- Disconnect the negative battery terminal to avoid short circuits and electric shock.
- Wear protective gloves to avoid scratching the dashboard and interior trim.
Step-by-Step Installation
- Take out the dedicated removal tool included in the package.
- Locate the original faulty power outlet socket on the vehicle dashboard or center console.
- Use the removal tool to firmly clamp the inner edge of the old socket.
- Gently pull outward to remove the old socket from its mounting hole.
- Disconnect the electrical wiring connector at the back of the old socket.
- Clean the dashboard mounting hole and wiring connector with a clean cloth.
- Connect the electrical connector firmly to the back of the new power outlet socket.
- Align the new socket with the original mounting hole, then press it inward until it snaps completely into place.
- Reconnect the negative battery terminal.
- Test the power supply function by inserting a cigarette lighter or phone charger to ensure power works normally.

Image: The 12V Power Outlet Socket and its dedicated Removal Tool.

Image: Angled view of the power outlet socket and removal tool, showing components.
Important Notes for Installation
- Always check the original part OE number (04793554AC) and compare product photos carefully before purchase to ensure compatibility.
- Do not use excessive force when removing the old socket to avoid damaging the dashboard trim.
- Ensure the electrical connector is fully locked before pressing the new socket into the mounting hole.
Operating Instructions
The 12V Lighter Power Socket provides a standard 12-volt power output for compatible automotive accessories, chargers, and devices. Once installed, it operates as a direct power source when the vehicle's ignition is on (or as per vehicle's specific wiring for accessory power).
Testing Functionality
After installation, insert a known working cigarette lighter or a phone charger into the new socket. Verify that the device receives power (e.g., phone starts charging, lighter heats up). If the device does not receive power, refer to the Troubleshooting section.
Maintenance
This power outlet socket is designed for durability and requires minimal maintenance. To ensure optimal performance and longevity:
- Keep the socket interior clean and free from debris, dust, or liquids. Use a dry, soft cloth for cleaning.
- Periodically check the connection of any inserted devices to ensure they fit snugly and maintain good electrical contact.
- Avoid inserting objects other than intended 12V accessories into the socket.
Troubleshooting
No Power from Socket After Installation
- Check Electrical Connection: Ensure the wiring connector at the back of the new socket is fully and securely attached.
- Check Vehicle Fuse: The 12V power outlet circuit is protected by a fuse in your vehicle's fuse box. Consult your vehicle's owner's manual to locate and inspect the relevant fuse. A blown fuse will prevent power from reaching the socket. Replace if necessary with a fuse of the correct amperage.
- Verify Device: Test the socket with a different 12V accessory to rule out a faulty device.
Socket Feels Loose After Installation
- Re-seat Socket: Ensure the new socket was pressed firmly into the mounting hole until it fully snapped into place. If not, gently remove it (using the tool if needed) and re-install, ensuring proper alignment and full engagement.
Specifications
| Feature | Detail |
|---|---|
| OE Part Number | 04793554AC |
| Input Voltage | 12V DC (Vehicle Standard) |
| Socket Diameter | 22 mm |
| Socket Length | 59 mm |
| Removal Tool Length | 176 mm |
| Material | Premium Hard Material (Anti-wear, Anti-aging) |
| Package Contents | 1x Power Outlet Socket, 1x Removal Tool |

Image: Dimensions of the 12V Power Outlet Socket and Removal Tool.
Compatible Vehicles (Reference Only)
Dodge: Grand Caravan, Journey, Durango, Avenger, Challenger, Charger, Dakota, Nitro, Ram 1500, Ram 2500, Ram 3500, Magnum
Jeep: Grand Cherokee, Wrangler, Commander, Liberty
Chrysler: Town & Country, 200, 300, PT Cruiser, Sebring, Pacifica
Note: OE Part Number is the best way to confirm fitment. Vehicle models are for reference only.
User Tips
- Always disconnect your vehicle's negative battery terminal before performing any electrical work to prevent accidental short circuits or injury.
- When removing the old socket, apply steady, even pressure with the tool to avoid damaging surrounding trim.
- Double-check all connections before re-connecting the battery and testing the new socket.
Warranty & Support
We provide professional customer service. If you have any installation or usage problems, please contact us immediately. We will reply and solve issues for you promptly.
Please note that damage caused by incorrect purchase (e.g., wrong OE part number) or improper installation is not covered by after-sales service.