1. Important Safety Instructions
WARNING: To avoid fire, shock, and serious personal injury, please read the following instructions carefully.
- Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
- Before installing the fan, disconnect the power by removing fuses or turning off circuit breakers.
- Make sure all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.
- Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blades.
- If you are mounting the fan on a ceiling outlet box, use a metal outlet box. Secure the box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at least 50 lbs.). Do not use a plastic outlet box. Attach the mounting bracket by using the hardware supplied with the ceiling outlet box.
- If you are mounting the fan to a joist, make sure it is strong enough to support the moving weight of the fan (at least 50 lbs.).
- After installing the fan, make sure all the connections are secured. This will prevent the fan from falling.
- Do not insert anything into the fan blades while the fan is operating.
- Turn the fan off and wait for it to stop before reversing fan direction.
- To reduce risk of electrical shock and personal injury, do not install the fan on a sloped ceiling.
- To reduce the risk of electrical shock and personal injury, do not use this fan with any solid-state.
- To reduce risk of personal injury, use only the two steel screws and lock washers provided with the fan for mounting the outlet box.
2. Setup and Installation
2.1. Unpacking Your Fan
Unpack your fan and check the contents. Please check each item prior to installation. To reduce the chance of marks or possible damages, please remove the parts when required for installation.
2.2. Parts List
| Ref.# | Description | Part# |
|---|---|---|
| 1 | Hanger Bracket | 1 |
| 2 | Canopy | 1 |
| 3 | Downrod Assembly | 1 |
| 4 | Coupling Cover | 1 |
| 5 | Fan Motor Assembly | 1 |
| 6 | Blade | 3 |
| 7 | Blade Decorative Plate | 1 |
| 8 | Plastic Cap | 1 |
| 9 | Remote Control | 1 |
2.3. Assembly Drawing (Without Light)
Refer to the diagram below for component identification and assembly order.

Diagram showing the various parts of the ceiling fan and their arrangement for assembly, including hanger bracket, canopy, downrod, coupling cover, fan motor assembly, blades, blade decorative plate, plastic cap, and remote control.
2.4. Installation Instructions (General)
- Securely attach the hanger bracket to the ceiling joist using the lag bolt, flat washer, and spring washer supplied. Ensure the joist is strong enough to support the fan's weight.
- Install the fan blades and blade decorative plate by aligning the holes on the blade and plate with the holes on the fan motor assembly. Secure with the provided set screws, ensuring they are tight and the blades are properly seated.
- Loosen the set screws in the Hanger Ball assembly until the ball slides carefully down the downrod. Remove the Pin from the downrod.
- Remove and save the clevis pin and hairpin of the downrod. Put the downrod through the canopy and coupling cover.
- Loosen two set screws on the downrod support and then place the downrod into the downrod support. Thread the electrical wires and the earth wire through the downrod. Align the Clevis Pin holes in the Downrod with the holes in the Downrod Support. Push the straight leg of the Hairpin Clip through the hole near the end of the Clevis Pin until the curved portion of the Hairpin snaps around the Clevis Pin. Finally, re-tighten the two set screws.
- Carefully lift the fan, and set the downrod/hanger ball assembly on the hanger bracket attached to the ceiling joist. Be sure the groove in the ball is properly aligned with the tab on the hanger bracket.
- Mount the canopy by tightening the two screws.
- Install the rubber plug into the motor axis.
WARNING: It is critical that the clevis screw in the downrod support is properly installed and the set screws are securely tightened. Failure to verify this could result in the fan falling.
WARNING: The fan must be hung with at least 230 cm of clearance from the floor to the blades.
2.5. Electrical Connections (Fan with Light)
WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.
- Connect 220-240V main power (dwelling) to the Terminal Block located on the hanger bracket. Plug the receiver in the hanger bracket with the flat side facing up.
- Insert the 3P connector of hanger bracket into the AC POWER INPUT socket of receiver.
- Insert the 2P light connector of fan motor assembly into the 2P LIGHT socket of receiver.
- Insert the 3P motor connector of fan motor assembly into the 3P MOTOR socket of receiver.
- Connect the 1P yellow/green connectors of fan motor assembly and hanger bracket.

Detailed wiring diagram showing connections for AC power, fan motor, and light kit to the receiver and hanger bracket.
2.6. Light Kit Installation (Fan with Light)
- Connect the wires from the motor assembly and wires from the LED correctly. Attach the light kit plate to the fan motor assembly using the two light kit plate screws.
- Install the shade into the light plate. Make sure it is secure but not overly tight.

Diagram illustrating the connection of the light kit to the fan motor assembly and installation of the light shade.
3. Operating Instructions
3.1. Remote Control Setting and Operation
The remote control uses RF wireless digital transmission technology for one-on-one control. It operates within an allowable space, and the direction is not limited.
Instructions for Remote Control Buttons:

Image of the remote control with numbered buttons. The remote controls fan speed, light on/off, fan direction, and timing.
- Turn off all loads
- Fan speed control
- LED indicator light
- Turn on the light
- Fan off
- Fan positive and negative rotation control
- Fan timing control
- The remote control uses a pair of 1.5V batteries.
- Test the battery, try the lamp, please replace the battery!
Pairing Remote and Receiver:
Turn on the power supply. Within 30 seconds, press and hold the transmitter's FAN ON/OFF button for 5 seconds. A beep will be heard, indicating successful pairing. All functions will then work normally.
Important: The initial pairing step must be performed within 30 seconds of power being turned on.
- When pairing multiple fans, ensure the isolation switch or power supply to the first installed fan is turned off prior to pairing further fans (e.g., pair one fan at a time).
- Ensure the isolation switch is kept to the ON position. It should not be used as a light switch, as this will damage the remote receiver.
3.2. Protective Functions of the Receiver
- Lock Protection: The DC motor has a built-in safety feature against blade or motor obstruction. If something obstructs the fan blades or motor, the motor will keep trying to run and then stop operation after about 30 seconds. Remove obstacles and reset by turning the fan off by remote transmitter and then turning it back on.
- Overload Protection (Current Limit): The device will limit the maximum current output from the receiver/drive if the fan load has increased abnormally.
3.3. Lighting Features

Illustration showing three light color temperatures: Cold Light (6000K), Natural Light (4000K), and Warm Light (3000K).
The fan light offers three color temperatures (3000K, 4000K, 6000K) to meet different needs and create various ambient scenes. Choose freely without selecting scenes.
3.4. Fan Rotation Modes

Diagram showing the fan's dual rotation capability: 'Summer turns positive' for strong wind and cool air, and 'Winter reversal' for circulating air to reduce temperature difference.
The fan features a front and back dual rotation design, allowing for a one-click switch to balance room temperature. In summer, the air is cool and not stuffy. In winter, the air circulation is fresh and flowing.
3.5. Adjustable Wind Speed

Image highlighting the adjustable wind speed feature with variable frequency 6-speed settings.
The fan offers variable frequency 6-speed settings, adjustable to meet the needs of the whole family.
4. Maintenance
- Periodic cleaning of your new ceiling fan is the only maintenance that is needed.
- When cleaning, use only a soft brush or lint-free cloth to avoid scratching the finish.
- Abrasive cleaning agents are not required and should be avoided to prevent damage to the finish.
WARNING: Do not use solvents when cleaning your ceiling fan. It could damage the motor and create the possibility of electrical shock.
Recommended:
Periodically check that the blade sets to the fan motor setscrews are secure and tight.
Note:
- Before carrying out any cleaning or maintenance work, always make sure that the appliance is disconnected.
- LED lights are not removable. LED lights can only be used within the product delivery; they cannot be replaced.
5. Troubleshooting
5.1. Balancing Fan / Wobbling Trouble Shooting
Please note that all ceiling fans are not the same; even in the same model, some may move more or less than others. Movement of a couple of centimeters is quite acceptable and does not suggest the fan will fall down. Even though all blades are weighted and grouped by weight, it is impossible to eliminate wobble altogether. This should not be considered a fault. Ceiling fans tend to move during operation due to the fact that they are not generally rigidly mounted.
To Reduce a Wobbling Fan:
- Check that all of the blade mounting screws are tightened and secure.
- Wobbling problems may result from inconsistent blade level. To check the blade level, measure the distance from each blade tip to the ceiling. Note: If measurements are inconsistent, be sure the blade mount screws are not too tight or too loose, which may cause wobbling due to an unlevel blade tip. An out-of-shape blade can cause wobbling. Check by removing the blade and placing it on a flat surface.
- Blade tracking may be checked simply by use of a household ruler. Place the ruler vertically against the ceiling and even with the outside leading edge of a blade. Note the distance of the edge of a blade compared to the others. Turn the blade slowly by hand to check the remaining blades. If a blade is not in alignment, the blade is either out of shape, warped, or the blade screws are not evenly tightened or either loose.
Balancing Kit:
A Balancing Kit has been provided to assist with reducing a wobble. Please retain the kit as it may become useful should the fan develop a wobble in the future. Instructions on how to use the Balancing kit can be found within the Kit.
5.2. Remote Control Issues
- If the transmitter functions are not working, check the battery orientation and power level. Low battery voltage will affect the functions of your transmitter and operation of your fan. Other remote controls nearby using the same frequency may cause interference with the fan's receiver.
- If the remote control cannot control the receiver, please check if there is any existence of similar remote-controlled products nearby, causing interference with each other.
- If the fan or light is not working, reset power (turn the power off for at least 5 seconds and then turn the power back on) and redo the learning function setting.
6. Specifications

Image displaying key product parameters including name, size, blade material, power, applicable space, and voltage.
| Attribute | Value |
|---|---|
| Product Name | Minimalist Fan Light |
| Model Number | XG-Ceiling fan lights |
| Size | 52 inches |
| Blade Material | Iron leaf |
| Power | 70W |
| Applicable Space | 6-12m2 |
| Voltage | 85-265V (Nominal: 120V-240V) |
| Luminous Flux | 2000-82000 |
| Control Method | Remote Control |
| Is Dimmable | Yes |
| Is Bulbs Included | Yes |
| Certification | CE, ROHS |
| Power Source | AC |
| Installation Method | Assembly |
| Package Weight | 5.6 kg |
| Package Dimensions | 55cm (L) x 22cm (W) x 24cm (H) |
6.1. Key Features
- High Transparency Lampshade: Made of high-quality materials with characteristics of sturdiness and high transparency.
- Hardware Baking Paint Process: The surface of the hardware lamp body is treated with baking paint, which is solid and not easily deformed, and has a long service life.
- Copper Variable Frequency Motor: Has low energy consumption and is quiet, providing comfortable and gentle blowing. Features bold copper wire, thickened steel, and double cover axle wheel.
- Widened and Thickened Iron Fan Leaves: Aerodynamic design, made of high-quality iron, not easily discolored.
- Stable Lighting: No flicker, reduces visual fatigue, adheres to the standard of no video flash to create comfortable lighting.
- Comfortable and Quiet Operation: Low noise during operation (10-20dB, comparable to fallen leaves or a very quiet room).

Close-up view of the high transparency lampshade, emphasizing its sturdy and clear material.

Image detailing the hardware baking paint process for durability and the high transparency of the lampshade.

Visual representation of the copper variable frequency motor, highlighting bold copper wire, thickened steel, and double cover axle wheel.

Close-up of the fan blade, showing its widened and thickened iron construction for aerodynamic performance.

Image demonstrating stable lighting with no flicker, reducing visual fatigue, and a phone capturing the fan's light.

Chart illustrating noise levels during fan operation, indicating 'Very Quiet' at 10-20dB, comparable to fallen leaves.
7. User Tips
- If your fan operates automatically after installation and power on, it is because it has memorized the previous factory setting. Use the Universal Mode or the learning function for normal operation.
- If the fan or light is not working, reset power (turn the power off for at least 5 seconds and then turn the power back on) and redo the learning function setting.
- It is not possible to remotely operate more than one fan in the same room (in the area where the remote signal can reach) if they share the same power supply. Separate power supplies (such as using individual wall switches for each fan) are required if you want to separately control more than one fan in the same room.
- When the fan is turned on or operated using the forward/reverse function, it may shutter and go back and forth until it turns. This is normal and will take a few seconds to run this operation.
- Remove batteries from the remote control if leaving unused for an extended period of time to avoid battery leaks.
- The receiver must be correctly installed in the mounting bracket on the fan.
- The isolation switch must be connected in the line.
- When power is cut to the unit (via a blackout or otherwise) and then restored, the light will come on.
8. Warranty and Support
This product comes with a 1-year warranty.
For detailed item guides and documents, including a comprehensive user manual in PDF format, please refer to the official documentation. You can view the user manual (PDF) here.