GGBEE E27 PIR Motion Sensor Converter

Contents

GGBEE E27 PIR Motion Sensor Converter

User Instruction Manual

1. Introduction

Thank you for choosing the GGBEE E27 PIR Motion Sensor Converter. This device transforms your standard E27 bulb sockets into intelligent, motion-activated lighting solutions, enhancing safety and convenience while conserving energy. Please read this manual carefully before installation and use to ensure proper operation and longevity of the product.

GGBEE E27 PIR Motion Sensor Converter

Figure 1: GGBEE E27 PIR Motion Sensor Converter

2. Product Features

  • Intelligent Detection Design: Internal lux sensor for automatic on/off based on ambient light (day/night).
  • Advanced Motion Detection: Built-in precision PIR sensors ensure instant light activation upon approach.
  • Adjustable Settings: Customizable time-delay and ambient light (LUX) sensitivity.
  • Wide Compatibility: Works with standard E27 bulbs, including LED, energy-saving, and incandescent lamps (up to 60W).
  • Wide Detection Range: 360° induction angle with a maximum detection distance of 6 meters.
  • Effortless Installation: Screws directly into existing E27 bulb sockets, no rewiring or special tools required.
  • Durable Construction: Made from PC flame retardant material for safety and impact resistance.
Intelligent detection design with internal lux sensor

Figure 2: Intelligent detection design with internal lux sensor for automatic operation.

3. Setup and Installation

3.1 Safety Precautions

  • Ensure power is turned off at the main switch before installation.
  • Do not exceed the maximum rated load of 60W.
  • This device is designed for indoor use only.
  • Do not install in locations with high humidity or direct water exposure.

3.2 Installation Steps

  1. Turn off the power supply to the light fixture at the circuit breaker.
  2. Unscrew the existing light bulb from the E27 socket.
  3. Screw the GGBEE E27 PIR Motion Sensor Converter into the E27 socket until it is firmly seated.
  4. Screw your desired E27 light bulb (LED, energy-saving, or incandescent, max 60W) into the sensor converter.
  5. Ensure the sensor lens is unobstructed and facing the desired detection area.
  6. Turn the power supply back on.

For optimal performance, install the sensor converter at a height between 2 meters and 3.5 meters.

Detection range diagram and installation height

Figure 3: Detection range (360° angle, 6m max distance) and recommended installation height (2m-3.5m).

International standard E27 interface

Figure 4: International standard E27 interface for easy installation.

4. Operating Instructions

The sensor converter features two adjustable knobs: TIME and LUX.

4.1 TIME-Delay Adjustment

  • This knob controls how long the light stays on after motion is no longer detected.
  • Counter-clockwise: Decreases the delay (minimum 10 seconds ± 3 seconds).
  • Clockwise: Increases the delay (maximum 300 seconds + 60 seconds, or 5 minutes ± 1 minute).

4.2 LUX Adjustment

  • This knob controls the ambient light level at which the sensor will activate.
  • Clockwise (towards 'Sun' symbol): Sets the sensor to work both day and night (maximum sensitivity).
  • Counter-clockwise (towards 'Moon' symbol): Sets the sensor to work only in low-light conditions (below 3 LUX, minimum sensitivity).
  • Note: When testing in daylight, ensure the LUX knob is turned fully clockwise (towards the 'Sun' symbol); otherwise, the sensor may not activate.
Adjustment instructions for TIME-delay and LUX settings

Figure 5: Detailed adjustment instructions for TIME and LUX settings.

4.3 Operational Sequence

  1. Daylight/Bright Conditions: If ambient brightness is greater than the set LUX threshold (e.g., >3 LUX when set to 'Moon'), the lamp remains off.
  2. Night/Low Light Conditions: If ambient brightness is below the set LUX threshold, and a person enters the 360° detection area, the light automatically turns on.
  3. Continuous Motion: The light remains on as long as the person moves within the detection area.
  4. No Motion: After the person leaves the sensing range, the light will automatically turn off after the set TIME-delay period expires.
Compatibility with various lamp types

Figure 6: The sensor converter is compatible with incandescent, energy-saving, LED, and retro lights.

5. Maintenance

  • Cleaning: To clean the sensor converter, gently wipe it with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as this may damage the device.
  • Lens: Ensure the sensor lens remains clean and free from dust or obstructions for optimal detection performance.
  • Material: The lamp body is made of PC flame retardant material, which is durable and impact-resistant.
Fire prevention feature

Figure 7: The device features fire-retardant PC material for enhanced safety.

6. Troubleshooting

Problem Possible Cause Solution
Light does not turn on when motion is detected.
  • LUX setting is too low (set to 'Moon') during daytime.
  • Bulb is faulty or not screwed in properly.
  • Power supply is off.
  • Motion is outside detection range.
  • Adjust LUX knob clockwise towards 'Sun' for testing or daytime operation.
  • Check and replace the bulb if necessary. Ensure it's screwed in tightly.
  • Verify power is on at the switch and circuit breaker.
  • Ensure motion occurs within 6m and 360° range.
Light stays on continuously.
  • Continuous motion in detection area.
  • Sensor is faulty.
  • Ensure no constant movement (e.g., pets, swaying curtains) is within the sensor's view.
  • Contact customer support if the issue persists after checking for motion.
Light turns on/off too frequently or at wrong times.
  • LUX setting is too sensitive for ambient light conditions.
  • TIME-delay setting is too short.
  • Adjust LUX knob counter-clockwise towards 'Moon' to reduce sensitivity to ambient light.
  • Adjust TIME-delay knob clockwise to increase the duration the light stays on.

7. Specifications

Parameter Value
Detection Range360°
Power Source100-240V/AC
Power Frequency50/60Hz
Rated Load<60W Max. (E27)
Detection Distance6m max (<24°C)
Time-DelayMin. 10sec ± 3sec; Max. 5min ± 1min (300sec + 60sec)
Ambient Light3-2000LUX (adjustable)
Working Temperature-20°C to +40°C
Installation Height2m - 3.5m
Base MaterialABS
Dimensions (Approx.)Height: 120mm; Base Diameter: 56mm; Top Diameter: 36mm
Product parameters with dimensions and specifications

Figure 8: Product dimensions and detailed specifications.

8. User Tips

  • Optimal LUX Setting: Experiment with the LUX setting during twilight hours to find the perfect balance where the light activates reliably when needed, but not prematurely.
  • Testing Time-Delay: When setting the TIME-delay, test it in real-world conditions to ensure the light stays on for a comfortable duration after you leave the area.
  • Placement: Consider the placement carefully to avoid false triggers from pets, swaying plants, or reflections, especially in areas with high traffic or environmental movement.
  • Bulb Choice: For best energy efficiency and longevity, use LED bulbs with this sensor converter.

9. Frequently Asked Questions (FAQ)

Q: Can this sensor be used outdoors?

A: No, this device is designed for indoor use only. Exposure to outdoor elements like rain or high humidity can damage the unit and pose a safety risk.

Q: What types of bulbs are compatible with this sensor?

A: It is compatible with standard E27 base bulbs, including LED, energy-saving (CFL), and incandescent bulbs, as long as the total wattage does not exceed 60W.

Q: Why does the light sometimes turn on during the day?

A: Check your LUX setting. If it's set too high (towards the 'Sun' symbol), the sensor will activate regardless of ambient light. Adjust it counter-clockwise towards the 'Moon' symbol if you only want it to activate in low-light conditions.

10. Warranty and Support

This product comes with a standard manufacturer's warranty. For warranty claims, technical support, or any questions not covered in this manual, please contact your seller directly. Please provide your purchase details when contacting support.

© 2024 GGBEE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.