saimili COB LED Strip Lights Motion Sensor

Contents

COB LED Strip Light with Motion Sensor User Manual

Model: COB LED Strip Lights Motion Sensor

1. Introduction

Thank you for purchasing the SAIMILI COB LED Strip Light with Motion Sensor. This flexible, USB-powered LED strip provides uniform, soft lighting for various applications such as kitchen cabinets, bedroom backlighting, and mirror illumination. Featuring a convenient hand-sweep motion sensor for on/off control and stepless dimming, this product offers both functionality and aesthetic appeal.

2. Package Contents

Please check the package for the following items:

  • 1 x COB LED Strip Light (selected length)
  • 1 x Hand Sweep Motion Sensor Switch (integrated with USB cable)

Note: Power adapter is not included. Please use a standard 5V USB power source.

3. Safety Information

  • This product operates on a low voltage (DC 5V). Do not connect it to higher voltage power sources.
  • Ensure the USB power source is stable and provides the correct voltage.
  • Do not immerse the LED strip or sensor in water. While the strip is IP20 rated, it is not fully waterproof.
  • Keep the LED strip unfolded during operation to prevent overheating.
  • Do not stare directly into the LED lights for extended periods.
  • Keep out of reach of children.

4. Setup Instructions

  1. Prepare the Surface: Clean the surface where you intend to install the LED strip with a dry cloth to ensure it is free of dust and grease.
  2. Measure and Cut (if necessary): Measure the desired length for your installation. The LED strip can be cut at designated cut marks (approximately every 25mm or 0.984 inches). Cutting at non-marked points will damage the strip.
  3. Apply the Strip: Carefully peel off the adhesive backing from the LED strip.
  4. Secure the Strip: Firmly press the LED strip onto the cleaned surface along its entire length.
  5. Connect Power: Plug the USB connector of the sensor switch cable into a 5V USB port (e.g., power bank, computer, USB wall adapter, TV USB port).
LED Strip Features: Flexibility, Cuttability, Double-sided Tape

Figure 4.1: LED strip features including flexibility, cut marks, and double-sided adhesive tape.

USB Power Sources for LED Strip

Figure 4.2: The LED strip can be powered by various 5V USB sources like power banks, computers, or USB adapters.

5. Operating Instructions

The LED strip is controlled by an integrated hand-sweep motion sensor.

  1. Turning On/Off: Wave your hand over the sensor (within 1-5cm) to turn the LED strip on or off.
  2. Stepless Dimming: To adjust brightness, hold your hand over the sensor for more than three seconds. The brightness will gradually increase to its highest level or decrease to its lowest level. Remove your hand when the desired brightness is reached.

Video 5.1: Demonstration of plugging in the USB, turning the light on/off with a hand sweep, and adjusting brightness by holding a hand over the sensor.

Adjustable Light Brightness Dimming

Figure 5.1: Illustration of how to dim the light by holding your hand over the sensor for more than 3 seconds.

Hand Sweep Sensor On Off

Figure 5.2: Visual guide for sweeping your hand to turn the light on (1) and off (2).

Dimmable Brightness Control

Figure 5.3: The sensor allows dimming from 25% to 100% brightness.

6. Maintenance

  • To clean the LED strip, gently wipe it with a soft, dry cloth.
  • Do not use abrasive cleaners or solvents, as these can damage the strip.
  • Ensure the power is disconnected before cleaning.

7. Troubleshooting

  • LEDs not lighting up: Ensure the USB connection is secure and the power source is active. Check if the strip was cut correctly at the designated marks.
  • Sensor not responding: When testing the sensor switch, do not hold the switch body. Wave your hand clearly over the sensor. Ensure input and output connections are correct (input side to power supply, output side to LED strip).
  • Overheating: Always keep the LED strip unfolded during usage to avoid heat accumulation.
  • Inconsistent light or dead LEDs: Incorrect cutting of the LED strip (not at cut marks) will lead to dead LEDs and is not repairable.
  • Color variation: Different batches of LED strips may have slight differences in color temperature. This is normal and not a quality issue.

8. Specifications

Product TypeUSB 5V COB LED Strip Light
Working VoltageDC 5V
Lamp BeadsCOB
Length Options1m / 2m / 3m / 4m / 5m
COB Width8mm
LEDs Quantity320 LEDs/meter
Luminous Flux100 LM/W (249-2000 LM total depending on length)
Waterproof GradeIP20
Color Rendering Index (RA)>90
Light Color OptionsCold White (6000K), Natural White (4000K), Warm White (3000K)
Average Life600,000 hours
CertificationsCE, EMC, ROHS

9. User Tips

  • Before purchasing, carefully measure the area where you plan to install the LED strip to ensure you select the correct length for your needs.
  • The soft and flexible nature of the COB strip makes it ideal for curved surfaces and creative lighting designs.

10. Warranty and Support

For any questions, technical support, or warranty claims, please contact the seller directly through your purchase platform. Please provide your order number and a detailed description of the issue for prompt assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.