Leeocar Wireless CarPlay Android Auto Car Radio For Toyota Camry 2007-2011 GPS Multimedia 2 Din 4G 64G Android 13

Contents

Leeocar Wireless CarPlay Android Auto Car Radio

User Manual for Toyota Camry 2007-2011

Model: Wireless CarPlay Android Auto Car Radio For Toyota Camry 2007-2011 GPS Multimedia 2 Din 4G 64G Android 13

Important Compatibility Notes

The original car with JBL/BOSS/BOSE amplifier cannot be installed with this unit. Neither of these two configurations can be used.

Hybrid, SE, and models with JBL Sound System require an additional CANBUS decoder & special cable to function correctly.

If you are unsure about the fit of your model, please contact support with a complete picture of the plugs on the back of the center console and the onboard main unit for review. This will help determine compatibility and confirm any additional wiring harnesses or adapters needed.

1. Setup and Installation

1.1. What's Included in the Package

The package typically includes the following components:

  • 1 x Car MP5 Player (Head Unit)
  • 1 x Power Cable
  • 1 x GPS Antenna
  • 1 x Camera (Rear View Camera)
  • 1 x Rear Camera Input Cable
  • 1 x RCA Cable
  • 2 x USB Cables
  • 1 x Crowbar (for trim removal)
  • 1 x Instruction Manual (this document)
  • GPS Module
Diagram showing included accessories and head unit dimensions
Figure 1: Included accessories and head unit dimensions (294mm/11.57in width, 140mm/5.51in height, 255mm/10in bottom width).

1.2. General Installation Guide

Warning: Do not connect wiring while power is on. Doing so may result in system errors, fuse damage, or permanent malfunction. Always disconnect the battery before installation.

CANBUS Warning: The CANBUS box has been connected to the wiring harness before shipment. Do not disconnect the CANBUS connector; functions may be disabled.

This radio is compatible with a wide range of models; however, some may have differing wiring harness layouts. Minor adjustments to the wiring might be necessary; otherwise, the radio may fail to power on. Should you encounter this issue, please contact support for guidance.

1.2.1. Radio Rear Panel Pinout Diagram

Refer to the diagram below for the pinout configuration of the head unit's rear panel. This is crucial for correct wiring.

Detailed wiring diagram for the car radio, showing connections for power, RCA, USB, camera, radio antenna, and GPS antenna.
Figure 2: Comprehensive wiring diagram for the car radio. Key connections include Power Cable (1), RCA Cable (2), USB Cable 1 (3), USB Cable 2 (4), CAM-IN Wire (5), Radio Antenna (6), and GPS Antenna (7).

1.2.2. Wiring Harness Connection Tutorial

Connect the plugs labeled on the original car radio. Remaining plugs may not need to be connected. If your vehicle has a JBL audio system, use the XC-1637 harness.

1.2.3. Steering Wheel Controls Setup

  1. Go to Car Settings > Factory (password: 000000) > CarType Setting, and select "NO Canbus".
  2. Then go to Car Settings > General > SWC Type, and select "Learning Type".
  3. Tap "Enter SWC setting interface" and follow the on-screen instructions to manually program your steering wheel control (SWC) keys.
Image showing the car radio interface with steering wheel control buttons highlighted.
Figure 3: Steering Wheel Control interface.

1.2.4. Rear Camera Wiring Tutorial

Connect the reversing camera to the dedicated input on the head unit. The package includes a rearview camera for safe parking. When the vehicle is reversing, the rear image will be automatically displayed on the screen, making your parking safer and easier.

Connect the 10-Pin Reversing Cable. (Ignore if not retaining the factory camera).

Note: Wires color may differ due to various batches, but pin locations will remain the same.

2. Operating Instructions

2.1. Core Features

  • Wireless Apple CarPlay & Voice Control: Supports wireless Apple CarPlay for Siri voice assist, accessing iPhone functions like music, navigation, calls, and messages. Connects via Bluetooth.
  • Wireless Android Auto & Voice Control: Connect your Android phone to access navigation, calls, messages, and music. Supports Voice Assistant for Android phones. Connects via Bluetooth.
  • Mirror Link: Mirror your phone screen (iOS or Android) on the stereo via hotspot/USB cable to access navigation, music, and other apps.
  • Wi-Fi Connection: Connect to Wi-Fi or a hotspot to download apps (YouTube, Spotify, Pandora), watch online videos, use online maps, or surf the internet.
  • GPS Navigation: Built-in GPS for offline navigation. With Wi-Fi/hotspot, access online maps. Compatible with most Play Store navigation apps (Sygic, Waze, Navitel IGO).
  • FM Radio Receivers: High-quality FM radio with unlimited preset stations, music, traffic info, and weather forecasts. Supports automatic or manual searching. FM Range: 87.5~108MHz.
  • Bluetooth Handsfree Calls: Supports hands-free calls for safe driving. Bluetooth music player for wireless audio streaming. Auto-loads phonebooks and synchronizes contacts.
  • Touch Screen Car Stereo: 9-inch high-definition large screen for a clear visual experience.
  • Steering Wheel Control: Allows easy control of songs, hands-free calls, and volume, reducing distraction while driving.
Image demonstrating Wireless CarPlay and Android Auto functionality on the car radio screen.
Figure 4: Intelligent Interconnection with Wireless CarPlay & Android Auto.
Image showing the car radio's dynamic sound settings and equalizer interface.
Figure 5: Dynamic Sound settings for audio customization.
  1. Turn on Wi-Fi and Bluetooth on your phone.
  2. On the radio, open the Bluetooth Phone app and find the corresponding Bluetooth device name. The PIN code is 0000.
  3. On your phone, go to Bluetooth settings, locate the radio's Bluetooth device name, enter the PIN code: 0000, and complete the pairing.
  4. For iPhone: Tap "Use CarPlay" when prompted, and set the device type as Car Stereo.
  5. For Android: Ensure Location is turned on and your phone supports wireless Android Auto (Android 11 or above is recommended).
  6. Open the ZLINK app on the car radio. CarPlay or Android Auto should launch automatically.

Tips:

  • If CarPlay/Android Auto doesn't appear, make sure your phone is not connected to any other wireless or Bluetooth devices.
  • Grant all required permissions when prompted on your phone.

2.3.1. For iOS (Wireless Mirroring)

  1. Open the ZLINK app on the car stereo and select "Wireless Mirroring".
  2. Enable your phone's cellular data and personal hotspot, and allow others to join.
  3. Connect the car stereo's Wi-Fi to the personal hotspot.
  4. Swipe down from the top of your phone screen to access the control center, tap "Screen Mirroring", and select "zj-airplay" to pair and complete the wireless mirroring connection.

2.3.2. For iOS (Wired Mirroring)

Open the "Zlink" app and switch to mirror function. Using the included 4-pin/6-pin USB cable, connect the USB cable to your phone to establish a connection, and follow the on-screen instructions.

2.3.3. For Android (Wireless Mirroring)

  1. On your phone, go to Bluetooth settings, locate the radio's Bluetooth device name, enter the PIN code: 0000, and complete the pairing.
  2. Open the ZLINK app on the radio and select "Wireless Mirroring".
  3. Scan the QR code to download the "zPlus" app.
  4. Enable your phone's hotspot and connect the radio's Wi-Fi to the phone hotspot.
  5. Open the "zPlus" app on your phone, select the connection method "Wireless Connection" to start mirroring and screen casting.

2.3.4. For Android (Wired Mirroring)

  1. On your phone, go to Bluetooth settings, locate the radio's Bluetooth device name, enter the PIN code: 0000, and complete the pairing.
  2. Open the ZLINK app on the radio and switch to wired mirroring mode.
  3. Use the 4Pin/6Pin USB cable provided to connect the USB data cable to your phone.
  4. Open the "zPlus" app on your phone and select the connection method "USB Connection" to establish the connection. The "zPlus" app should launch automatically.

3. Maintenance

3.1. System Update (OTA Upgrade Method)

To ensure optimal performance and access to the latest features, regularly check for system updates.

  1. Tap "Check for Updates" in the System Update screen.
  2. If a new version is found, tap the "Download Update" button.
  3. The device will automatically unzip and reboot to start the upgrade process.
  4. After the upgrade, the head unit will reboot again automatically.
Screenshots showing the Device Information Interface, System Update Screen, MCU Update, and System App interfaces for OTA upgrades.
Figure 6: OTA Upgrade Method and Feature Demonstration screens.
Screenshots detailing download instructions for system updates and a forced upgrade feature.
Figure 7: Download Instructions and Forced Upgrade Feature details.

3.2. Forced Upgrade Feature

To address issues like system crashes, freezes, or lags, a forced upgrade feature has been added. If normal version checks prevent downloading updates when the current and server versions match, this feature allows manual reinstallation of the firmware.

Note: The forced upgrade is hidden.

After tapping "Check for Updates" and receiving the message "No update needed," tap the "Download Update" button ten times consecutively. A password input prompt will appear—entering the correct password will allow the update to proceed. This mechanism prevents misuse of the download function.

4. Troubleshooting (FAQs)

Q1: What is the factory password?
A: 000000
Q2: The rear camera image is reversed (left to right). How can I fix it?
A: Please go to Car Settings > General and toggle the "Rear Mirror" option to adjust.
Q3: Why is the factory rear camera image not clear?
A: The factory rear camera image may not be clear enough because the old camera signal uses CVBS (360P), while this new radio screen supports AHD (1080P). It is recommended to use the supplied camera for better image quality.
Q4: How do I turn off the camera's guideline?
A: Please go to Car Settings > General and turn off "Reverse Line".
Q5: What should I do if the radio experiences issues like freezing and stuttering?
A: Please go to Settings > System > Reset options > Erase all data (factory reset).
Q6: Is it possible to support Sirius XM radio?
A: No, the radio does not have a port for connecting a SiriusXM tuner for Satellite Radio. You may check the radio's Play Store for online SiriusXM Radio apps, but compatibility with third-party apps cannot be guaranteed.
Q7: Does it support the factory microphone?
A: No, the factory microphone cannot be retained. Connect the external microphone to the 3.5mm port on the RCA cable. Install the microphone on the driver's side sun visor, with the microphone head facing the driver's face.
Q8: Can I use a voice assistant (Siri, etc.)?
A: The voice assistant can only be activated through your phone. Connect your phone to the radio via Bluetooth, Android Auto, or CarPlay, and then use the voice assistant feature on your phone.
Q9: Why is the time not accurate?
A: Ensure your GPS antenna is properly connected. Install the GPS antenna on the A-pillar of your car or just outside the dash (it will not work if installed inside the dash). Next, connect your radio to Wi-Fi or a hotspot, then go to Settings > System > Date and Time, and enable "Use network provided time" and "Use network-provided time zone."
Q10: Why is the WiFi connection unstable?
A: Verify that the single yellow RCA camera port is properly connected to the radio, as the adjacent small wires are intended for receiving Wi-Fi and Bluetooth signals. Also, note that Bluetooth and Wi-Fi cannot be used at the same time.
Q11: What should I do if the original car protocol-related information display or the original car-related settings show errors?
A: Select the corresponding car model according to the car model protocol selection chart provided. Connect the car radio to the internet, then go to Car settings > System > CAN Apk Update to complete the upgrade.
Q12: How do I change the custom boot logo/startup logo?
A: Download the desired image (resolution 1280x720, PNG format), rename it to "zxdzlogo", and place it in the root directory of a USB drive. Insert it into the device. Go to local upgrade: Settings > System > About device > Local Update > select the logo and start the upgrade. After the upgrade, go to Car Settings > Factory (password: 000000) > Dedicated logo settings > Boot Screen Logo to change the logo.
Q13: How do I use the offline map, navigation, and GPS functions?
A: Install the GPS antenna on the A-pillar of your car or just outside the dash. For GPS navigation, connect your radio to Wi-Fi or a hotspot, then open the maps app for online navigation. For offline navigation, connect to Wi-Fi first to download maps to the radio's internal storage. Once downloaded, you can use the maps without an internet connection. Alternatively, you can connect via CarPlay or Android Auto to use GPS/navigation.

5. Specifications

Attribute Value
High-concerned chemical None
Warranty 1 Year
Preset Station Set by yourself
Tuner Type Support FM, AM (Optional)
Built-in DVD Player No
Built-in CD player No
Chipset Query sales page details
Processor Type Query sales page details
Is touch screen Yes
Built-in Screen Yes
Category Combination product
TF/Micro SD Slot 2
Din Double Din
RAM 4G (Available in 2GB/4GB configurations)
Interface USB/RCA
Operating System Android 13
Out Power 4*45W
Voltage 12 V
Item Weight 2.5kg
Output Type Colored
Max External Memory 64G (Available in 32GB/64GB configurations)
Special Features Wi-Fi function, Support 4G Network, Built-in GPS, Split Screen, MP3 players, CarPlay, Voice Control, Android Auto, DSP, Reversing Input, Support steering wheel control, Support Can-Bus
Digital Media Format MP4, Mp3, WMA, JPEG
OSD Language Multi-language support including English, Chinese, Arabic, German, French, Japanese, Spanish, etc.
Display Size 9"
Origin Mainland China
ROM 64G (Available in 32GB/64GB configurations)
Accessory Type Query sales page details
Certification CE, FCC, WEEE, EAC, RoHS, KC
Material Composite Material
Online Radio Search multiple channels (Optional)
Support Wireless Android Auto/CarPlay Sync phone to Radio (Optional)
GPS navigation map Built-in offline map, free update
AV-OUT Need converter
Support AI voice control Allow you to make phone calls, navigate, play music... (Optional)
Image showing the 1280x800HD screen resolution and IPS display features.
Figure 8: Full HD 1280*800 IPS Screen features.

6. Warranty and Support

6.1. How to Access Technical Support

For any issues not mentioned in this FAQ, or for further assistance, please contact customer support. You can also refer to the official website for after-sales support and community forums.

A detailed user manual in PDF format is available for download: View User Manual (PDF)

Note: We strongly recommend professional installation. For usage guidance, installation inquiries, or any other questions, please reach out to us via email. We stand ready to assist.

7. User Tips

  • Installation is generally straightforward, making it a convenient upgrade for compatible vehicles.
  • For optimal GPS performance, install the GPS antenna on the A-pillar or outside the dash; avoid installing it inside the dash.
  • When using CarPlay or Android Auto, ensure all required permissions are granted on your phone when prompted.
  • For stable wireless connections, avoid using Bluetooth and Wi-Fi simultaneously if you experience instability.

© 2024 Leeocar. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.