1. Product Information
1.1 Introduction
This product is a DC submersible pump, with optional voltage specifications: 12V/24V/36V/48V/60V/72V. It is suitable for power supply scenarios of different electric vehicles and batteries. The pump features a full copper motor and a stainless steel impeller design, offering compact and portable size, energy efficiency, strong pumping power, and corrosion resistance. It is designed to meet various water intake and drainage needs.
1.2 Core Advantages
- Full Copper Motor: Equipped with pure copper coils, cold-rolled silicon steel sheets, and high-precision steel bearings, delivering strong power and supporting long-term operation without easy burnout, ensuring a longer service life.
- Stainless Steel Impeller: Corrosion-resistant and wear-resistant, adapting to various water qualities for stable pumping efficiency.
- Safety Protection: Features an IPX8 waterproof design and overheat protection, ensuring safe and reliable underwater use, and avoiding risks of electric leakage and motor burnout.
- Energy Saving & Power Efficiency: Low power consumption design extends battery life for longer usage at lower cost.
- Lightweight & Portable: Stainless steel and ABS housing with a non-slip handle make it easy to install, carry, and move.
- Corrosion & Rust Resistance: The stainless steel pump body and anti-rust coating make it suitable for complex water environments such as rivers, wells, and aquaculture ponds.
2. Setup
2.1 Voltage Matching Instructions
Please select the pump with the corresponding voltage according to your power supply equipment to avoid equipment damage caused by mismatched voltage:
| Power Supply Equipment | Suitable Pump Voltage |
|---|---|
| 1×12V Battery | 12V |
| 2×12V Batteries (Series) | 24V |
| 4×12V Batteries (Series, 48V Electric Vehicle) | 48V |
| 5×12V Batteries (Series, 60V Electric Vehicle) | 60V |
| 6×12V Batteries (Series, 72V Electric Vehicle) | 72V |
2.2 Wiring Method
- 12V/24V Pumps: Can be directly connected to the battery using the matching battery clips. Connect the red wire to the positive (+) terminal and the black wire to the negative (-) terminal. DO NOT reverse the connection!
- 48V/60V/72V Pumps: Directly connect to the power interface of the corresponding voltage electric vehicle or the corresponding series battery pack, ensuring the wiring is firm and loose-free.
- After wiring, test the pump operation briefly to confirm no reverse rotation or abnormal noise before submerging it in water.
2.3 Installation
- Install the Water Outlet Connector: Select a water pipe with appropriate caliber and install it firmly on the pump outlet to ensure no water leakage or falling off risk.
- Place the Pump: Put the pump into the water stably, with the water inlet at least 10cm away from the bottom of the pool/well to avoid sucking in sediment and debris that may block the impeller. It is recommended to fix the pump with a rope to prevent tipping or displacement.
3. Operating Instructions
3.1 Power On & Start
Power on only after the pump is completely submerged in water. Dry running is strictly prohibited, as it will cause the motor to overheat and burn out.
3.2 Precautions During Operation
- Do not pull or tug the power cord while the pump is working to avoid wiring detachment or damage.
- If the water flow suddenly decreases, abnormal noise or vibration occurs, cut off the power immediately to check and eliminate blockage or impeller jamming issues.
- The single continuous working time is recommended not to exceed 4 hours to avoid motor overheating affecting service life (except models with overheat protection).
4. Application Scenarios
This pump meets various water intake and drainage needs, functioning as a multi-purpose device:
- Agricultural Irrigation: Farmland watering, garden irrigation, vegetable garden water supply.
- Domestic Water Intake: Well water pumping, river water intake, home car washing.
- Drainage & Sewage: Canal drainage, low-lying land drainage, construction site drainage.
- Aquaculture Use: Aquaculture water exchange, poultry breeding water supply, fish pond oxygenation assistance.
Video 1: Demonstration of the DC Submersible Pump in various applications, showcasing its water pumping capabilities for irrigation and cleaning.
5. Maintenance & Care
- Daily Cleaning: After each use, rinse the pump surface and water inlet with clean water to remove sediment, water plants, and other debris. This prevents long-term adhesion that may corrode the pump body.
- Regular Inspection: Check the power cord and terminals for damage or oxidation once a month. Inspect the impeller for wear and pump body sealing integrity every 3 months.
- Long-Term Storage: When not in use for a long time, thoroughly clean and dry the pump. Store it in a cool, dry, and ventilated place, avoiding moisture, direct sunlight, and extrusion.
6. Troubleshooting
| Fault Phenomenon | Possible Causes | Solutions |
|---|---|---|
| Pump fails to start | Incorrect wiring / Dead battery / Poor power contact | Check positive and negative wiring, confirm battery power, re-connect firmly |
| Weak water flow / Low output | Blocked water inlet / Worn impeller / Leaky pipe / Insufficient voltage | Clean inlet debris, check impeller damage, replace damaged pipes, confirm matching supply voltage |
| Abnormal noise / Vibration | Impeller jamming / Pump not level / Damaged bearing | Power off and clean impeller debris, re-place the pump stably, contact after-sales for bearing replacement if damaged |
| Frequent motor burnout | Dry running / Excessive voltage / Long-term overload operation | Strictly prohibit dry running, confirm voltage matching, control single continuous working time |
7. Safety Precautions
- Dry running is strictly prohibited! The pump must be completely submerged in water before powering on, otherwise the motor will overheat and burn out, which is not covered by the warranty.
- Always disconnect the power before wiring. Do not operate with electricity. Confirm no short circuit or leakage risk before powering on after wiring.
- Do not use this pump in flammable and explosive environments to avoid safety accidents caused by electric sparks.
- Children and inexperienced persons should not use the pump alone to avoid electric shock or equipment damage risks.
- Do not touch the pump body with hands while it is working to avoid burns (the motor generates heat during operation).
- Do not lift the pump by pulling the power cord. To move the pump, cut off the power first and lift the pump body with a rope.
- If the pump inlet sucks in a large amount of sediment or debris, cut off the power immediately to clean it, avoiding blockage that may damage the impeller and motor.
Reminder: Before use, please confirm that the power supply voltage matches the pump specifications. Operate strictly in accordance with the instructions to extend the service life of the equipment and avoid potential safety hazards.
8. Specifications
- Product Name: Pump
- Model: 202512011003985
- Material: Copper (Motor), Stainless Steel (Impeller, Pump Body)
- Voltage Options: 12V, 24V, 36V, 48V, 60V, 72V
- Waterproof Rating: IPX8
- Features: Overheat protection, non-slip handle
- Battery Included: No
- High-concerned chemical: None
- Origin: Mainland China
- Package Dimensions (Approx.): Length 31cm, Width 25cm, Height 24cm
- Package Weight (Approx.): 4.2 kg
9. Warranty & Support
For warranty information, please refer to the terms provided by your seller at the time of purchase. For technical support or inquiries, please contact the manufacturer or your point of purchase.
A detailed user manual in PDF format is available for download. Please refer to the seller's product page for the link to the PDF document.