HTBCCHB Radiator Cooler Water Tank

Contents

HTBCCHB Radiator Cooler Water Tank User Manual

For Bashan 200CC 250CC BS200 BS200S-7 UTV ATV Quad Bike Buggy Engines

1. Product Overview

This manual provides essential information for the safe and effective installation, operation, and maintenance of your HTBCCHB Radiator Cooler Water Tank. This product is a core safety component designed for motor vehicle cooling systems.

Key features include:

  • High-efficiency aluminum heat dissipation fins for excellent cooling performance.
  • Built-in protective mesh grille to prevent gravel from damaging radiator fins.
  • Equipped with a pressure relief radiator cap for stable cooling system pressure.
  • Multi-hole fixed mounting for direct bolt-on replacement without modification.
  • Constructed from corrosion-resistant aluminum alloy for durability and long service life.
Front view of the HTBCCHB Radiator Cooler Water Tank
Figure 1: Front view of the Radiator Cooler Water Tank.

2. Safety Warnings

Please read all instructions carefully before use. Improper operation may cause engine overheating, boiling, and cylinder scoring, resulting in severe mechanical damage and safety accidents.

  • Hole Position Matching Requirements: Select 3-hole / 4-hole installation specifications strictly according to the original vehicle. It is forbidden to install radiators with mismatched hole positions incorrectly.
  • Coolant Specifications: Only special anti-freeze coolant for motorcycles shall be used. Do not add tap water for a long time to avoid scaling, blockage, and corrosion of water channels.
  • Air Bleeding Operation: The air inside the cooling system must be completely exhausted after installation. It is forbidden to start the vehicle or drive on the road before the air is fully removed.
  • High Temperature Warning: Do not open the water tank cap when the engine is hot. Spraying of high-temperature and high-pressure coolant may cause severe scalds.
  • Leakage Test: Pressure test and leak detection of the entire pipeline must be carried out after installation. The product can be used normally only when there is no leakage and the water temperature operates stably.
  • Children Warning: Coolant is toxic and highly corrosive. Please keep it out of children's reach to prevent accidental ingestion.

3. Setup and Installation

3.1. Installation Preparation

  1. Turn off the engine, cut off the power supply, and allow the vehicle to cool down completely.
  2. Drain all the original old coolant completely.
  3. Clean any scale and impurities from engine water channels and pipeline joints.
  4. Verify that the radiator hole positions and water port specifications fully match your original Bashan vehicle model.
  5. Check that the water tank is intact and has good sealing.
  6. Prepare special antifreeze, pipe clamps, fixing bolts, and sealing gaskets.

3.2. Installation Procedures

  1. Fix the radiator at the corresponding 3-hole / 4-hole mounting positions. Tighten bolts evenly to ensure stable installation without shaking.
  2. Connect engine inlet and outlet cooling hoses. Fasten pipe clamps securely.
  3. Connect the overflow hose of the auxiliary water tank.
  4. Slowly pour antifreeze up to the standard scale.
  5. Idle the engine for circulation to completely exhaust air inside the system.
  6. Test the operation of the cooling fan.
  7. Check that there is no leakage in all pipelines and that the water temperature remains stable.
  8. Arrange pipelines and wiring harnesses properly to avoid interference with other components.
Angled view of the radiator cooler showing cooling fins
Figure 2: Angled view of the Radiator Cooler, highlighting cooling fins.

4. Operating Instructions

Proper operation of the cooling system is crucial for engine longevity and performance.

  • Air Bleeding: Ensure all air is completely exhausted from the cooling system after installation and before operating the vehicle. Air pockets can cause localized overheating.
  • Cooling Fan Check: Regularly verify that the cooling fan operates correctly, especially when the engine reaches operating temperature or under heavy load.
  • Temperature Monitoring: Always monitor your engine's temperature gauge. If the engine overheats, safely pull over and allow it to cool before inspecting the cooling system.
  • Leakage Check: Periodically check for any signs of coolant leaks around the radiator, hoses, and connections. Address any leaks immediately.
  • High Temperature Precaution: Never open the radiator cap when the engine is hot, as pressurized hot coolant can cause severe burns.

5. Maintenance and Care

5.1. Storage

Store unused radiators in a dry and cool place. Prevent impact damage to cooling fins and extrusion deformation.

5.2. Regular Maintenance

  • Cleaning: Regularly clean sediment and dust from the protective grille and cooling fins to avoid blockage that reduces heat dissipation efficiency. This should be done every 3 months.
  • Regular Inspection: Check pipeline aging, water tank leakage, water tank cap pressure relief, and coolant level every 500 kilometers.
  • Fluid Replacement Cycle: Replace the antifreeze of the whole vehicle every 1-2 years or 5000 kilometers to ensure long-term stability of the cooling system.
  • Replacement Time Limit: Replace the radiator immediately if it cracks, leaks, or the fins are severely deformed and corroded.

5.3. Prohibited Operations

  • Do not strike or squeeze the cooling core with hard objects.
  • Do not operate the vehicle under overload, long-time high load, and high-temperature conditions.

6. Troubleshooting

Many common issues can be prevented or resolved by following the safety warnings and maintenance guidelines.

  • Engine Overheating: If your engine overheats, first ensure the coolant level is correct. Check for air trapped in the system (perform air bleeding), verify the cooling fan is operating, and inspect the radiator fins for blockages from dirt or debris. Also, check for any visible leaks.
  • Coolant Leaks: Inspect all hose connections, the radiator core, and the radiator cap for signs of leakage. Tighten loose clamps or replace damaged components.
  • Poor Cooling Performance: This can often be attributed to clogged radiator fins, insufficient coolant, or air in the system. Ensure regular cleaning and proper coolant levels.

7. Specifications

AttributeDetail
Brand NameHTBCCHB
Model NameRadiator Cooler Water Tank
MaterialAluminum Alloy
ColorSilver
Mounting Hole Options3 Holes / 4 Holes
Fit Engine Displacement200cc - 250cc
Compatible ModelsBashan BS200, BS200S-7 UTV, ATV, Quad Bike, Buggy
Overall Length304 mm
Overall Height160 mm
Core Width113 mm
Mounting Point Width153 mm
Radiator cooler with key dimensions overlaid
Figure 3: Radiator Cooler with key dimensions.

8. User Tips

No specific user tips were available from customer reviews or Q&A for this product at this time. Always refer to the manufacturer's guidelines and your vehicle's service manual for best practices.

9. Disclaimer

The manufacturer and store shall not be liable for any engine failure, vehicle damage, or personal injury caused by mismatched hole positions, improper exhaust installation, unqualified coolant, overload and high-temperature operation, or artificial collision damage.

For further details, you may refer to the official user manual PDF: View User Manual (PDF)

© HTBCCHB. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.