JIKONG QB2A8S20PHC

Contents

JK BMS Smart Active Balance QB2A8S20PHC User Manual

Model: QB2A8S20PHC

Brand: JIKONG

1. Introduction

The JIKONG JK BMS Smart Active Balance QB2A8S20PHC is an advanced Battery Management System designed for large capacity series lithium battery packs. It provides comprehensive protection and management features for Li-ion, LiFePO4, and LTO battery types, supporting configurations from 3S to 8S depending on the battery chemistry.

Key functionalities include high-current active balancing, precise voltage acquisition, overcharge, over-discharge, over-current, over-temperature, and low-temperature protection. The BMS also integrates a coulomb meter for accurate capacity tracking, Bluetooth communication for mobile app control, GPS interface support, and a heating function for cold environments. This manual provides detailed instructions for the safe and effective use of your JK BMS.

2. Safety Information

Please read and understand all safety instructions before installing or operating the JK BMS. Failure to follow these instructions may result in electric shock, fire, serious injury, or property damage.

  • Always disconnect the battery pack from any loads or chargers before performing any wiring or maintenance.
  • Ensure all wiring is correct and secure. Incorrect wiring can cause damage to the BMS, battery, or connected equipment.
  • Wear appropriate personal protective equipment (PPE), including safety glasses and insulated gloves, when working with batteries.
  • Avoid short-circuiting battery terminals or BMS connections.
  • Do not expose the BMS to water, moisture, or extreme temperatures outside its operating range.
  • Ensure proper ventilation around the battery pack and BMS.
  • If any abnormal behavior is observed (e.g., smoke, unusual odors, excessive heat), immediately disconnect the battery pack and seek professional assistance.
  • Only use the BMS with compatible battery types and cell counts as specified in the product specifications.

3. Package Contents

Carefully unpack your JK BMS and verify that all items are present and in good condition.

JK BMS QB2A8S20PHC Package Contents

Figure 3.1: JK BMS QB2A8S20PHC Package Contents

  • JK BMS Main Board (QB2A8S20PHC)
  • 3.2-inch LCD Display Unit
  • LCD Display Connection Cable
  • Balance Wires Harness
  • Temperature Sensor Wires (NTC probes)
  • Strong Start Switch
  • Strong Heat Switch

4. Specifications

The following table details the technical specifications of the JK BMS Smart Active Balance QB2A8S20PHC.

JK BMS QB2A8S20PHC Key Specifications

Figure 4.1: JK BMS QB2A8S20PHC Key Specifications Overview

ParameterValueUnit
Supply Voltage12-40V
Operating Power Consumption1000-1400mW
Operating Temperature-30 to 70°C
Max. Collection Strings8S
Max. Active Balance Current2A
Max. Continuous Charge Current200A
Max. Continuous Discharge Current200A
Max. Instantaneous Current400A
Max. Starting Current3000A
Max. Internal Loop Resistance0.3mΩ
Dimensions (L×W×H)227×120×23.12mm
Finished Weight620g
JK BMS QB2A8S20PHC Dimensional Drawing

Figure 4.2: Dimensional Drawing of JK BMS QB2A8S20PHC

4.1 Battery Compatibility

The JK BMS QB2A8S20PHC is compatible with the following battery types and string counts:

  • Li-ion (Ternary Lithium): 3-8 Series
  • LiFePO4 (Lithium Iron Phosphate): 4-8 Series
  • LTO (Lithium Titanate): 7-8 Series

5. Setup

5.1 Wiring Diagram

Careful and correct wiring is critical for the safe and proper operation of the BMS. Refer to the wiring diagram below for detailed connections. Ensure all connections are secure before powering on the system.

JK BMS QB2A8S20PHC Wiring Diagram

Figure 5.1: JK BMS QB2A8S20PHC Wiring Diagram

Wiring Steps:

  1. Connect Battery Negative (B-): Connect the main negative terminal of your battery pack to the B- terminal on the BMS.
  2. Connect Battery Positive (P+): Connect the main positive terminal of your battery pack to the P+ terminal on the BMS.
  3. Connect Balance Wires: Connect the balance wire harness to the corresponding connector on the BMS. Ensure each cell's positive terminal is connected to the correct balance wire (B1, B2, B3... up to B8). The first balance wire (B0 or B-) should connect to the main negative of the battery pack.
  4. Connect Temperature Sensors (NTC): Plug the NTC temperature probes into their designated ports on the BMS. Place the probes strategically on battery cells to monitor temperature.
  5. Connect LCD Display: Connect the 3.2-inch LCD display unit to the 'Display Interface' port on the BMS using the provided cable.
  6. Connect Optional Switches: If using, connect the 'Strong Start Switch' and 'Strong Heat Switch' to their respective ports.
  7. Connect Charger and Load: Connect your charger and load to the appropriate terminals (P+ and P- or B+ and B- depending on common/separate port configuration).
  8. Connect Optional GPS/Communication Modules: If using, connect GPS module or RS485/CAN communication modules to their respective interfaces.

5.2 Connector Definitions

The BMS features various connectors for different functions. Refer to the detailed pinout for correct connections.

ConnectorInterface NamePin No.Pin NameDescription
P1 (XH2.0-9P)Balance & Acquisition1B-Total Negative Battery
2B11st Cell Positive
3B22nd Cell Positive
4B33rd Cell Positive
5B44th Cell Positive
6B55th Cell Positive
7B66th Cell Positive
8B77th Cell Positive
9B88th Cell Positive
P2 (XH2.0-4P)Temperature Interface 11T1A1st Temp Sensor Pin A
2T1B1st Temp Sensor Pin B
3T2A2nd Temp Sensor Pin A
4T2B2nd Temp Sensor Pin B
P3 (XH2.0-4P)Temperature Interface 21T3A3rd Temp Sensor Pin A
2T3B3rd Temp Sensor Pin B
3T4A4th Temp Sensor Pin A
4T4B4th Temp Sensor Pin B
P5 (A1254WF-4A)Strong Start Switch1LED-LED Indicator Negative
P6 (A1254WF-4A)Communication Interface1RS485-BRS485 Data B
2RS485-ARS485 Data A
3CAN-HCAN High
4CAN-LCAN Low
P7 (A1254WF-6A)Display Interface1VCCDisplay Power Output
2ADisplay RS485 Signal Positive
3BDisplay RS485 Signal Negative
4GNDPower Negative Terminal
5K+Activate Positive Signal
6K-Activate Negative Signal
P8 (1.25T-4PWT)GPS Interface1VGPSPower Output (close to B+)
2TXUART TX, 3.3V
P9 (A1254WF-2A)Alarm Interface1V+Alarm Output 12V Positive
2V-Alarm Output 12V Negative
P10 (M3-PCB)Heating Interface1HT-Heater Element Negative
P11 (M3-PCB)Power Input1B+Power Input Positive
D1Bluetooth Connection Indicator (Steady on when connected, blinking when disconnected)
P-Connect to external load or negative terminal of charger
B-Connect to the negative battery terminal

5.3 APP Installation

The JK BMS can be managed and monitored via a mobile application. To install the app:

  1. Scan the QR code below with your smartphone's camera or a QR code scanner app.
  2. Follow the on-screen instructions to download and install the application.
  3. Ensure your Android device is running Android 7 or higher for compatibility.
JK BMS APP QR Code (Placeholder)

Figure 5.2: Mobile APP Link QR Code (Note: Actual QR code not provided, generic image used)

6. Operating Instructions

6.1 Device Activation

Before powering on the BMS, double-check all wiring, especially the balance cables and main power connections (P- and B-). Ensure the BMS is securely mounted to the battery pack.

The BMS is designed for charger activation. After completing the battery assembly, connect a charger (with voltage 2V higher than battery voltage) to activate the BMS. Alternatively, the BMS can be activated via the display unit (if connected) or by pressing a connected activation button.

6.2 Mobile App Usage

Once the BMS is activated, you can connect to it via Bluetooth using the mobile app.

JK BMS Mobile App Interface

Figure 6.1: JK BMS Mobile App Interface

  1. Open the JK BMS app on your smartphone.
  2. Enable Bluetooth on your phone and search for available devices.
  3. Select your JK BMS from the list to connect.
  4. The app will display real-time battery information, including cell voltages, total voltage, current, temperature, and state of charge.
  5. Navigate through the app to access various settings and controls.

6.3 Key Features and Functions

The JK BMS offers a wide range of features for optimal battery management:

  • Active Equalization: The BMS actively balances cell voltages by transferring energy from higher-voltage cells to lower-voltage cells, ensuring battery consistency and extending lifespan. The default balance current is 2A, configurable via the app.
  • Heating Function: For low-temperature environments, the BMS supports an optional heating function (4A current) using a resistance heater or film to maintain optimal battery performance. This can be controlled via the app or a forced-heat switch.
  • Comprehensive Protections: Includes overcharge, over-discharge, over-current (charge/discharge), over-temperature, low-temperature (charge), and short-circuit protection. All protection parameters are configurable via the app.
  • Alarm and Fan Control: Provides a 12V output for driving an alarm or a cooling fan when protection thresholds are met.
  • Intelligent Sleep Mode: Reduces BMS power consumption by entering sleep mode when current is below 1A for 26 consecutive hours, reactivated by button press or charger connection.
  • Communication Interfaces: Supports CAN and RS485 for integration with other systems.
  • GPS & Display Interface: Dedicated ports for connecting a GPS module for location tracking and an LCD display for local monitoring.
JK BMS Key Features

Figure 6.2: JK BMS Key Features

JK BMS Protection Features

Figure 6.3: JK BMS Protection Features

Active Equalization Diagram

Figure 6.4: Active Equalization Process

7. Maintenance

The JK BMS is designed for reliable operation with minimal maintenance. However, periodic checks can help ensure its longevity and optimal performance.

  • Visual Inspection: Periodically inspect the BMS and its wiring for any signs of damage, corrosion, or loose connections.
  • Firmware Updates: Check the manufacturer's website or app for any available firmware updates to ensure your BMS has the latest features and bug fixes.
  • Parameter Review: Occasionally review the BMS parameters via the mobile app to ensure they are still appropriate for your battery pack's condition and usage patterns.
  • Cleaning: Keep the BMS free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquid cleaners.
  • Temperature Monitoring: Ensure the battery pack and BMS operate within their specified temperature ranges. Address any issues causing excessive heat or cold.

8. Troubleshooting

If you encounter issues with your JK BMS, refer to the following common troubleshooting steps:

ProblemPossible CauseSolution
BMS not powering on/activatingIncorrect wiring; Charger not connected or insufficient voltage; BMS in sleep mode.Verify all wiring connections; Connect a charger with appropriate voltage; Activate via button/display if applicable.
Bluetooth connection issuesBluetooth off on phone; App not updated; BMS too far from phone.Ensure phone Bluetooth is on; Update app; Move phone closer to BMS.
Battery not charging/dischargingBMS in protection mode (e.g., overvoltage, undervoltage, overcurrent); Loose connections.Check app for active protections and address the cause; Verify all power connections.
Cells not balancingBalance function disabled in app; Large cell voltage difference; Faulty balance wires.Enable balance function in app; Allow time for balancing; Check balance wire integrity.
Over-temperature warningsBattery or BMS overheating; Faulty temperature sensor.Reduce load/charge current; Improve ventilation; Check NTC sensor connection and placement.

If the problem persists after trying these steps, please consult the manufacturer's support.

9. User Tips

  • Initial Setup: Always perform a thorough check of all wiring connections before the first power-up to prevent damage.
  • App Customization: Take time to explore the mobile app settings. Adjusting protection parameters to match your specific battery chemistry and usage can optimize performance and lifespan.
  • Temperature Management: If operating in cold climates, utilize the heating function to maintain battery efficiency and prevent low-temperature charging issues.
  • Monitoring: Regularly check cell voltages and temperatures via the app, especially during the first few charge/discharge cycles, to ensure proper operation and identify any potential issues early.

10. Warranty and Support

JIKONG products are manufactured to high-quality standards. For warranty information and technical support, please refer to the official JIKONG website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

© 2024 JIKONG. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.