1. Introduction
Thank you for purchasing the KKMOON Digital Sound Level Meter DM219N. This device is a 3-in-1 meter designed to accurately measure sound levels (decibels), ambient temperature, and humidity. It features a clear LCD display with backlight, making it suitable for various environments such as homes, offices, workshops, schools, and libraries. This manual provides essential information for the safe and effective use of your device.

Figure 1: Digital Sound Level Meter DM219N Display
2. Package Contents
Please check the package contents upon unboxing:
- Digital Sound Level Meter DM219N
- USB Type-C Charging Cable (1.2m)
- User Manual (this document)
3. Setup
3.1 Charging the Device
- Connect the provided USB Type-C charging cable to the Type-C port on the side of the meter.
- Connect the other end of the USB cable to a standard USB power adapter (5V, 1A/2A, not included).
- The indicator light on the device will display red while charging.
- Once fully charged (approximately 2 hours), the indicator light will turn green. A full charge provides approximately 24 hours of continuous use.

Figure 2: Device with USB Charging Cable
3.2 Device Placement
The DM219N is designed for desktop placement, offering convenience and saving space as it does not require handheld operation. Its compact and portable design allows you to place it anywhere you need accurate environmental readings, such as on a desk, shelf, or table in your office, home, workshop, or classroom.
4. Operating Instructions
4.1 Device Overview

Figure 3: Front and Top View of the Device with Labeled Components
- Noise Meter Probes: Sensors for sound level detection.
- Decibel (dB): Displays the current sound level.
- Temperature (°C/°F): Displays the ambient temperature.
- Time: Displays the current time.
- Battery Indicator: Shows the current battery level.
- Decibel Level Indicator: A visual bar graph representing the sound level.
- Power Button: Used to turn the device on or off.
- Type C Port: For charging the device.
- Humidity (%RH): Displays the relative humidity.
- Setup Button: Used for accessing settings (e.g., time adjustment, temperature unit).
- Right Button: Used for navigation or increasing values in settings, and adjusting screen brightness.
- Left Button: Used for navigation or decreasing values in settings, and adjusting screen brightness.
- Air Inlet: Allows air circulation for temperature and humidity sensors.
4.2 Powering On/Off
Press and hold the Power Button (located on the right side of the device) for a few seconds to turn the device on or off.
4.3 Real-time Monitoring
Once powered on, the device will immediately begin displaying real-time measurements for:
- Noise Level: Shown in decibels (dBA) with a range of 30-130dBA.
- Temperature: Shown in Celsius or Fahrenheit.
- Humidity: Shown as a percentage of relative humidity (%RH).
4.4 Adjusting Screen Brightness
To adjust the screen brightness, press the Left Button or Right Button (located on the top of the device) to cycle through available brightness levels.
4.5 Setting Time and Temperature Unit
Press the Setup Button (located on the top of the device) to enter the settings menu. Use the Left and Right buttons to navigate through options (e.g., time adjustment, 12/24-hour format, temperature unit °C/°F) and adjust values. Press the Setup button again to confirm selections or exit the menu.
5. Maintenance
5.1 Cleaning
To clean the device, gently wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the device's surface or internal components.
5.2 Important Safety Warning
WARNING: DO NOT IMMERSE IN WATER!
This device is not waterproof. Exposure to water or other liquids can cause severe damage and void the warranty.
6. Troubleshooting
- Device does not turn on: Ensure the device is fully charged. Connect it to a power source using the USB cable and allow it to charge for at least 30 minutes before attempting to power it on again.
- Display is dim or unreadable: Adjust the screen brightness using the Left and Right buttons. If the issue persists, the battery may be low; recharge the device.
- Readings appear inaccurate: Ensure the device is placed in an open area, away from direct heat sources, cold drafts, or obstructions that might affect sensor readings. Avoid placing it near loud machinery or in direct sunlight for accurate temperature/humidity readings.
- Device not holding a charge: Ensure you are using the provided USB Type-C cable and a compatible 5V power adapter. If the issue persists, the internal battery may need service.
7. Specifications
| Feature | Specification |
|---|---|
| Product Name | Digital Decibel Meter Desktop Sound Level Meter |
| Model | DM219N (10212401151) |
| Noise Measurement Range | 30-130dBA |
| Accuracy | ±1.5 dBA |
| Frequency Range | 50Hz-8.5kHz |
| Frequency Weighting | A |
| Display Accuracy | 0.1dBA |
| Sampling Time | 1.5 seconds |
| Temperature Measurement Range | 14℉-140℉ (-10℃-60℃) |
| Humidity Measurement Range | 20%-85% |
| Battery | Built-in 2000mAh Rechargeable Li Battery |
| Charging | USB Type-C, 5V 1A/2A |
| Battery Included | Yes |
| Certification | CE |
| Package Length | 19 cm |
| Package Width | 12 cm |
| Package Height | 8 cm |
| Package Weight | 0.489 kg |
8. User Tips
- For the most accurate sound level readings, place the meter in the center of the area you wish to monitor, away from walls or reflective surfaces.
- Ensure the air inlet is not obstructed to allow proper functioning of temperature and humidity sensors.
- Regularly check the battery indicator and recharge the device to ensure continuous operation and reliable data.
9. Warranty and Support
9.1 Warranty Information
Warranty terms and conditions for this product are typically provided by your retailer or the manufacturer at the time of purchase. Please retain your proof of purchase for any warranty claims.
9.2 Manufacturer Information
Manufacturer: shanghai huang shi mao yi Co., Ltd.
Address: Room 3389, Building 2, No. 88, Changxu Road, Juyuan New District, Jiading District, Shanghai
Email: b162sumaitn2822@163.com
Telephone: +86-13876659222
9.3 EU Authorized Representative
Company Name: SOLID AUTHORITY LIMITED
Address: IE-51 Bracken Road, Sandyford, Dublin 18, D18 CV48, Ireland
Email: phoebe8706@gmail.com
Telephone: +33-761441379
9.4 Additional Resources
For detailed instructions and further information, please refer to the complete User Manual PDF available at: User Manual (PDF)