Benro GD36

Contents

Benro GD36 Spherical Quick Adjustment Gear Pan Tilt Head User Manual

Model: GD36

Introduction

Thank you for choosing the Benro GD36 Spherical Quick Adjustment Gear Pan Tilt Head. This innovative gear head combines the flexibility of a spherical pan-tilt with the precise adjustment of a gear pan-tilt, designed for accurate and precise composition in photography. To ensure optimal performance and longevity, please read these instructions carefully before use.

The Benro GD36 features a self-researched design, incorporating fine and tightly engaged gears for smooth and accurate adjustments. It is built with a 36mm large sphere and offers excellent damping adjustment for universal, fast, and smooth composition.

Product Overview

The Benro GD36 is a spherical quick adjustment gear pan/tilt head. Below is an overview of its functional parts.

Diagram of Benro GD36 Gear Head with labeled functional parts
Figure 1: Product Functional Parts Overview
  • 1/4" Camera Screw: For attaching your camera.
  • Quick-loading Plate Locking Knob: Secures the quick-release plate.
  • Lateral Pitch Knob: Adjusts the lateral tilt of the head.
  • Horizontal Locking Knob: Locks the horizontal rotation.
  • Circular Level: Helps ensure the head is level.
  • Longitudinal Pitch Knob: Adjusts the longitudinal tilt of the head.
  • Initial Damping Adjusting Knob: Fine-tunes the damping resistance.
  • Ball Lock Knob: Locks the spherical movement.
  • Yajia/Akka Base with 3/8" Screw Hole: For mounting the head onto a tripod or monopod.

Setup Instructions

Mounting the GD36 Head to a Tripod/Monopod

The GD36 head features a 3/8" screw hole on its base for mounting onto a tripod or monopod. Ensure your support system has a compatible 3/8" mounting thread. If your tripod/monopod uses a 1/4"-20 thread, you may need an adapter (not included) or to reverse the mounting screw on your tripod/monopod if it supports it.

  1. Screw the GD36 head clockwise onto the 3/8" mounting thread of your tripod or monopod until it is hand tight.
  2. Secure the head by fully tightening any head locking screws present on your tripod/monopod base.
  3. Ensure enough screw threads are engaged for maximum security. It is recommended that at least 5 to 6 threads are exposed before locking.

Attaching Your Camera

The GD36 head comes with a quick-release plate system. Attach the quick-release plate to your camera's 1/4" tripod socket, then slide the plate with the camera into the head's receiver and secure it using the quick-loading plate locking knob.

Operation

Basic Adjustments

Diagram showing numbered adjustment knobs on Benro GD36
Figure 2: Brief Description of Use
  • Ball Lock Knob (1): Turn this knob to adjust the coarse composition and lock the sphere's main movement.
  • Longitudinal Pitch Knob (2): Use this knob for fine adjustment of the longitudinal pitch, allowing for a range of ±15°.
  • Horizontal Adjustment Knob (3): Adjusts the horizontal position for fine composition.
  • Horizontal Locking Knob (4): Locks the head horizontally after making adjustments.

Damping Adjustment

The GD36 allows you to adjust the damping to suit the weight of your camera and lens, and your preferred feel.

Diagram illustrating damping adjustment with Ball Locking Knob and Initial Damping Knob
Figure 3: Damping Adjustment
  1. Rotate the Ball Lock Knob (1) counter-clockwise to its starting position.
  2. Pull out the Initial Damping Knob (2) with one hand.
  3. While holding the Initial Damping Knob, slowly spin the head and gradually adjust the damping until it feels right for your equipment.

Adjusting the initial damping can reduce the expansion of the spherical pan/tilt and prevent picture offset, especially with longer focal length lenses (above 300mm).

Pitch Adjustment Ranges

Diagram showing longitudinal pitch adjustment range of +/- 15 degrees and lateral pitch adjustment range of +/- 8 degrees
Figure 4: Pitch Adjustment Ranges
  • Longitudinal Pitch Adjustment Range: ±15°
  • Lateral Pitch Adjustment Range: ±8°

The longitudinal pitch adjustment knob allows for two-way adjustment, accommodating both left-handed and right-handed users.

Maintenance

Cleaning

  • Always clean and dry the GD36 head after exposure to wet, dusty, sandy, or salty conditions.
  • Use a mild soap solution applied with a soft cloth, rinse with fresh water, and dry with a soft towel.
  • Remove any dust, dirt, or sand from all moving parts and knobs.
  • Do not use the head in salt water.

Restoring Gear Tightness

The gears and worm gears are metal parts and may wear after long-term use, potentially leading to loosening. The GD36 includes manual adjustment to restore tightness.

Diagram showing longitudinal and lateral adjusting screws for tightness
Figure 5: Tightness Adjustment Screws

To restore tightness, adjust the longitudinal and/or transverse screws as needed. Note that new gimbal gear and worm gear are not worn and do not require direct adjustment.

General Care

  • Do not leave the GD36 head in direct sunlight for prolonged periods or expose it to high temperatures.
  • Avoid leaving the head unattended in areas where people could trip over the equipment.
  • Always remove the camera and lens from the GD36 head when transporting.

Troubleshooting

The GD36 design aims to mitigate common issues found in spherical pan-tilt heads.

  • "Nodding" Phenomenon: The GD36 is designed to address the "nodding" phenomenon (slight movement after locking) that can occur when the lock is not tight. Its gear structure with an "automatic locking" function helps prevent this by automatically locking into a suitable position.
  • Composition Offset: The GD36's gear pan-tilt fine-tuning is designed to prevent composition offset that can occur when a spherical pan-tilt is finally locked.
  • Gear Loosening: Manufacturing tolerances in traditional gear pan-tilts can lead to idling stroke and loosening over time. The GD36's design, including manual adjustment capabilities, aims to prevent gear structure idling and loosening after long-term use.

If you experience persistent issues, please refer to the Warranty/Support section for contact information.

Specifications

Product parameters table for Benro GD36
Figure 6: Product Parameters
Benro GD36 Product Parameters
FeatureDetail
NameGD36
Quick-loading Plate ModelPU56
Sphere Diameter36mm
Height105mm
Base Diameter46mm
Base Screw3/8"
Weight0.66kg
Load Bearing6kg
MaterialAluminum alloy
Dimensions (L*W*H)98*98*105 mm
OriginMainland China

User Tips

No specific user tips were available from provided reviews or Q&A content. However, general best practices for gear heads include:

  • Always ensure all locking knobs are securely tightened before leaving your camera unattended.
  • Practice adjusting the damping and pitch controls to become familiar with the head's responsiveness for different camera setups.
  • When making fine adjustments, use gentle, controlled movements to avoid overshooting your desired composition.

Warranty and Support

Benro gear is manufactured to provide years of dependable service. For detailed warranty information and support, please visit the official Benro website or contact their customer service.

For additional documentation, including a user manual in PDF format, you may refer to the following link: Benro GD36 User Manual (PDF).

For your safety, do not allow your Benro gear to come into contact with any electrical power source.

Benro Contact Information (from general Benro manual):
8 Westchester Plaza
Elmsford, NY 10523
T: 914.347.3300
F: 914.347.3309
Email: info@Benro.com
Website: Benro.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.