GGBEE ZN02

Contents

GGBEE LED Night Light with Motion Sensor

Instruction Manual

1. Introduction

Thank you for purchasing the GGBEE LED Plug-in Night Light. This manual provides important information regarding the safe operation, installation, and maintenance of your new night light. Please read all instructions carefully before use and retain this manual for future reference.

IMPORTANT: FOR INDOOR AND DRY LOCATION USE ONLY.

2. Parts Identification

Familiarize yourself with the components of your LED Night Light:

Diagram showing parts of the LED Night Light: Control Button, Motion Sensor, and ON/OFF/AUTO switch.

Figure 1: LED Night Light Components

  • Control Button: Used for adjusting brightness and changing light color.
  • Motion Sensor: Detects movement to activate the light in AUTO mode.
  • Switch: Toggles between ON, OFF, and AUTO modes.
  • Light Source: Integrated LED for illumination.

3. Setup

To set up your LED Night Light:

  1. Unpack the night light from its packaging.
  2. Plug the LED night light into a standard wall socket. It can be oriented upright or facing downwards, as shown in the diagram below.
Diagram showing how to plug the night light into a wall socket, upright or downfacing.

Figure 2: Plug Orientation (Refer to the bottom left of the image for FIG.1 and FIG.2)

CAUTION: Risk of electric shock and fire hazard. This product is not a toy and is not intended for use by children. For adult use only. Do not plug in extension cords. Indoor use only. For safe use, plug only into exposed wall outlets where the night light is ventilated and cannot contact bed coverings or other material that may present a fire hazard.

4. Operating Instructions

4.1. Switch Settings

Use the slide switch on the top of the device to select the desired operating mode:

  • ON Mode: The night light will turn on constantly and remain lit.
  • OFF Mode: The night light will turn off.
  • AUTO Mode (Motion Sensor ON): The night light will automatically turn on when its sensors detect a lack of ambient light and motion. After approximately 30 seconds, it will automatically turn off when motion stops or with an increase in ambient light.
Visual representation of LED Night Light OFF mode, ON mode, and Motion Sensor ON mode.

Figure 3: Operating Modes

Note: The motion sensor function (AUTO mode) only operates in dark surroundings. The light will remain off during daytime or when sufficient ambient light is detected.

4.2. Control Button Functions

The control button (small button next to the switch) allows for brightness and color temperature adjustments:

  • Long Press: Adjusts brightness steplessly from 15% to 100%.
  • Short Press: Changes the light color temperature in sequence: Warm White (2700-3000K) → Cold White (6000-6500K) → Mixed Light (4500-5000K).
Image showing light color adjustable feature, switching between Cold White and Warm White.

Figure 4: Adjusting Light Color

Memory Function:

The night light retains the last set brightness and light color when operating in AUTO mode (requires continuous power connection). This saves you from readjusting settings each time.

5. Maintenance

  • Cleaning: Ensure the device is unplugged before cleaning. Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Light Source: This device uses a non-replaceable LED light source. When the light source reaches the end of its life cycle, the entire device should be replaced.
  • General Care: Do not disassemble this device. Do not expose it to dripping or splashing water. Do not install this device near heat sources. Do not place any sources of danger on this device (e.g., liquid filled objects, lighting candles).

6. Troubleshooting

If you encounter issues with your night light, please refer to the following common solutions:

ProblemPossible CauseSolution
Light does not turn on.
  • Not plugged in correctly.
  • Switch is in OFF mode.
  • In AUTO mode, ambient light is too bright.
  • No motion detected in AUTO mode.
  • Ensure the light is securely plugged into a working outlet.
  • Slide the switch to ON or AUTO mode.
  • Test in a darker environment.
  • Ensure motion is within sensor range (3-5m).
Light stays on constantly in AUTO mode.
  • Constant motion detected within sensor range.
  • Sensor is obstructed or faulty.
  • Ensure no continuous movement near the sensor.
  • Check if anything is blocking the sensor.
Light turns on during daylight.Light sensor is not detecting enough ambient light.Ensure the light sensor is not obstructed and is exposed to ambient light.

If problems persist, please contact the store for assistance. Our customer service will be happy to assist you.

7. Specifications

Diagram showing product dimensions and a table of parameters.

Figure 5: Product Dimensions and Parameters

ParameterValue
Model NumberZN02
Input VoltageAC90-240V
Power0.6W (0.8W on some models)
Brightness10-60 Lumens (10-30LM stepless dimming)
Light SourceLED bulbs
Color TemperatureWarm White (2700-3000K), Mixed Light (4500-5000K), Cold White (6000-6500K)
Sensor TypeLight Sensor & PIR Motion Sensor
Sensor Range3-5 meters
Sensor Angle100 degrees
Delay Time20-30 seconds
Body MaterialABS + PC
Ingress Protection LevelIP20
Lifespan20,000 hours
CertificationsCE, ROHS

8. User Tips

No specific user tips were available from provided reviews or Q&A content.

9. Warranty and Support

This GGBEE LED Night Light comes with a 1-year warranty from the date of purchase.

For any issues, questions, or warranty claims, please contact the seller or the store where you purchased this product. Our customer service team is available to assist you.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.