GGBEE Motion Sensor light

Contents

GGBEE Ultra Thin Motion Sensor LED Cabinet Light User Manual

Model: Motion Sensor Light (Available in 20CM, 30CM, 40CM, 50CM lengths)

1. Product Overview

The GGBEE Ultra Thin Motion Sensor LED Cabinet Light is a versatile, rechargeable lighting solution designed for various indoor applications such as kitchens, bedrooms, wardrobes, and desks. It features intelligent motion sensing, adjustable brightness, and three selectable light color temperatures.

GGBEE LED Cabinet Light showing warm, natural, and white light options
The GGBEE LED Cabinet Light offers three color temperatures: Warm Light (3000K), Natural Light (4000K), and White Light (6000K).
Close-up of the GGBEE LED Cabinet Light's control panel with USB charging port and mode/dimming buttons
The ultra-thin design (11mm thick) includes a USB charging port and intuitive controls for mode selection and brightness adjustment.

2. Package Contents

Please check the package for the following items:

Diagram showing the contents of the product package: outer box, lamp body, fixed buckle with adhesive, USB charging cable, and instructions.
Product List Details:
  1. Packaging outer box
  2. Lamp body
  3. Fixed buckle with adhesive backing
  4. USB charging cable
  5. Instructions (PDF version available: View PDF)

3. Setup and Installation

3.1 Initial Charge

Before first use, please fully charge the lamp. The charging indicator will light red during charging and turn green when fully charged.

3.2 Installation Steps (No wiring, no punching)

Three-step simple fixation diagram for the LED cabinet light
Simple 3-step fixation process for easy installation.
  1. Install the fixing clip on the lamp body and adjust it to the appropriate position at both ends (recommended to install at 1/3 of each end).
  2. Remove the adhesive paper from the back of the fixed clip and stick it to the target position. Ensure the surface is clean and dry.
  3. Once the fixed clips are in place, the lamp body can be magnetically adsorbed to the clips. The lamp body can be removed and fixed at any time.

Note: The magnetic strip has two sides: one metal surface and one paste surface. The correct installation method is to glue the adhesive surface of the magnetic disk to the wall/cabinet surface, and then adsorb the lamp body to the metal surface. The adhesive surface of the magnetic disc should not be glued to the lamp body itself.

The number of magnetic plates is consistent with the number of magnets in the lamp body, and the number of magnetic plates with different lengths of lamps is different.

Wireless installation with magnetic adsorption, showing easy setup and light modes
Wireless installation using magnetic adsorption for convenience.

4. Operating Instructions

4.1 Power Button and Mode Selection

Diagram showing the different modes and brightness adjustment for the LED cabinet light
A variety of modes can be adjusted, including constant light, night sensing, and all-day sensing.
  • Short Press: Cycles through White Light, Warm Light, and Neutral Light. (Note: Monochrome models do not have this function).
  • Long Press: When the light is on, hold down the key to adjust the brightness. Release the key to lock the brightness. The lamp has a brightness memory function.

4.2 Sensing Modes

The lamp offers three sensing modes:

  1. Constant On Mode: Press the button once to enter this mode. The induction function is inactive.
  2. Night Sensor Mode: Press the button a second time. The light body flashes 3 times, then enters night induction mode. In this mode, the lamp will only light up automatically when it senses a person in insufficient light conditions.
  3. Daytime Induction Mode: Press the button a third time. The light body flashes 2 times, then enters daytime induction mode. In this mode, the lamp will automatically light up when it senses a person, regardless of ambient light conditions.
  4. Off: Press the button a fourth time to turn off the lamp.

4.3 Motion Sensor Functionality

Diagram illustrating the motion sensor's 3-meter sensing distance and 120-degree wide angle range
The motion sensor has a 3-meter sensing distance and a 120-degree wide-angle range.
  • The sensor range is 120°, within 3 meters of the probe as the center point.
  • When a person leaves the sensing area, the light will automatically turn off after about 25 seconds.
  • If a person remains active within the sensing area, the light will continue to stay on.

5. Maintenance

5.1 Cleaning

Use a soft, dry cleaning cloth to clean the lamp body. Do not use abrasive cleaners or solvents.

5.2 Battery and Light Source

The product's light source and battery are not replaceable. After a long period of use, if the product's power is low in the full power state or the battery life shortens under normal use, the entire lamp should be replaced.

6. Troubleshooting

  • Light not turning on after charging: Ensure the lamp was fully charged before first use. The light may not turn on due to circuit protection if not fully charged initially.
  • Sensor not working or inconsistent:
    • Ensure the installation position is not too low, too high, or too deep.
    • Check for any barriers near the induction probe that might affect the induction range.
    • Glass can block human body sensing; avoid placing the sensor behind glass.
    • Improper installation or occlusion near the sensor will affect its effect.
    • Ensure the lamp is not in constant on mode if you expect sensing functionality.
  • Brightness weakening or short battery life: The service life of the lamp body after a single full charge varies with individual use. The longer the daily lighting time, the faster the power consumption. When brightness is low, charge the lamp promptly to avoid affecting normal use.
  • Charging issues:
    • Do not use charging equipment with an output voltage greater than 5V.
    • For safety and efficiency, use a mobile phone charging adapter with safety certification.
    • Do not use the lamp while charging, as the charging indicator light interferes with the human body sensing function.

7. Specifications

Feature Detail
Brand Name GGBEE
Model Number Motion Sensor light
Lengths Available 20cm (2 LEDs), 30cm (2 LEDs), 40cm (3 LEDs), 50cm (4 LEDs)
Is Bulbs Included Yes
Luminous Flux 249-2000 lumens
Material PP
Is Dimmable Yes (Stepless dimming)
Power Generation Motion
Voltage 5V
Power Source Rechargeable battery (Type-C charging port)
Certification CE
Installation Method Self-contained (Magnetic adsorption)
Sensing Distance Within 3 meters
Sensing Angle 120° wide angle
Automatic Turn-off Approx. 25 seconds after leaving sensing range
Product Dimensions (approx.) Length: 20/30/40/50cm, Width: 5cm, Height: 3cm
Product Weight (approx.) 0.215 kg

8. User Tips

  • Optimal Placement: For best motion sensing performance, install the light in a position where the sensor has a clear line of sight to the area you want to illuminate. Avoid placing it behind obstructions or glass.
  • Charging Frequency: The battery life varies with usage. If you notice the light dimming or turning off quickly, it's time to recharge.
  • Brightness Memory: Take advantage of the brightness memory function by setting your preferred brightness level once; the light will remember it for future use.
  • Energy Saving: Utilize the night sensor mode in areas where light is only needed when it's dark, maximizing battery efficiency.

9. Warranty and Support

For any product inquiries, technical support, or warranty claims, please contact the seller directly through the platform where you purchased the product. Keep your purchase records for reference.

© 2024 GGBEE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.