1. Introduction
The Hantek HT2018B/C Series Battery System Tester is a performance testing tool specifically designed for activated lead-acid batteries. It is used to assess the startup process, charging process, and battery performance under electric load. The HT2018C model includes a Bluetooth printing function for startup process test reports.
This product is suitable for battery production and sales, auto parts maintenance, and various equipment systems that rely on lead-acid batteries. It provides rapid and accurate analysis of the battery's life state.
Features:
- Excellent design, easy to operate, accurate readings, and comprehensive functions.
- Large screen dot matrix liquid crystal display for clear information.
- Utilizes precise internal circuitry and a powerful digital processing unit with a four-wire Kelvin test connection method for accurate data acquisition and operation.
- Enhanced protection for input signal lines against errors, including polarity reversal, high voltage connection, and poor test clamp contact, ensuring safer and more convenient use.
- Directly tests car load state, starting voltage, and charging voltage.
- Low frequency signal testing eliminates the need for external large load discharge.
- Estimates battery lifecycle by easily reading electrical capacity and physical condition.
- Allows direct testing on the car without removing the battery.
- Continuous operation with full overvoltage and reverse connection protection.
- No electricity, no heat, no sparks, and no operating danger, making it user-friendly.
- Battery test includes cold starting current, internal resistance, voltage, and lifecycle analysis.
- Starting test monitors battery status during system startup.
- System test evaluates output state during charging system operation.
- Maximum load test assesses battery performance under peak load conditions.
For a detailed overview of the product, you can watch this video:
Video: Demonstration of Hantek automotive diagnostic equipment (Note: This video features the Hantek 6074BE, a different model, but illustrates general automotive testing principles).
2. Safety Requirements
This manual provides essential instructions and safety warnings for the proper use and maintenance of the instrument. Failure to follow these guidelines may result in damage to the instrument or personal injury. This instrument is designed and manufactured in strict compliance with GB4793.1 electronic measuring instrument and IEC/EN61010-1 safety standards, meeting double insulation overvoltage standard CAT III 600V and pollution level 2 safety design.
- The HT2018B/C is suitable for detecting 6V, 12V, and 24V batteries.
- The working voltage range of HT2018B/C is DC 4.5V ~ 30V.
- If the car engine is running, do not place the instruments and accessories near the engine or exhaust pipe to avoid high temperature damage.
- Always pay attention to car manufacturers' warnings and maintenance procedures when working on automobiles.
- Before use, check the test clamps and cables for any damage to the insulation layer, breakage, or exposed wires. Do not use if damaged.
- Do not use or store the instrument in high temperature, high humidity, flammable, explosive, or strong electromagnetic environments.
- Do not modify the instrument's internal circuit. Unauthorized modifications can damage the instrument and compromise safety.
- Wear qualified eye protection when testing or repairing cars to prevent foreign matter from entering the eyes.
- Operate and repair vehicles in a well-ventilated environment to prevent inhalation of toxic gases.
International Electrical Symbols:
| Symbol | Description |
|---|---|
| --- | DC |
| ~ | AC |
| ~ | DC/AC |
| ⚠ | Warning caution safety sign |
| ⚡ | Dangerous voltage (danger of electric shock) |
| ⏚ | GND |
| ☐ | Double insulated and highly insulated |
| ⌧ | Fuse |
| + | Battery |
3. Product Overview and Components
The Hantek HT2018B/C Battery System Tester is a compact and robust device designed for easy handling and clear display of test results.
Figure 1: Front view of the HT2018B Battery Tester.
Figure 2: HT2018B Battery Tester with connected red (positive) and black (negative) clamps.
Function Keys and Test Clamps:
- <▲> <▼>: Recurring, decreasing, up and down page keys.
- <ESC>: Cancel, return key.
- <ENTER>: Confirm, enter and test key.
- Intermediate key: Enters the printing interface.
- Red test clamp: Positive connection test clamp.
- Black test clamp: Negative connection test clamp.
Figure 3: Dimensions of the HT2018B Battery Tester (140mm x 75mm x 30mm).
4. Setup and Initial Connection
Before performing any tests, ensure the vehicle is in a safe state and the tester is correctly connected.
Preparation:
- If the car is in motion, turn off the engine and set the ignition key to the OFF position.
- If the battery has just been charged or the vehicle has been running, the voltage might be slightly higher than normal. Turn on the headlights for 2-3 minutes to stabilize the voltage before testing.
- Inspect the test clamps and cables for any damage or exposed wiring. Do not use if damaged.
Connection Steps:
- Connect the red test clamp to the battery's positive (+) terminal.
- Connect the black test clamp to the battery's negative (-) terminal.
- Ensure good contact between the clamps and battery terminals to avoid affecting test results.
Figure 4: Proper connection of the tester to a car battery.
5. Operating Instructions
The HT2018B/C Battery System Tester offers various functions to diagnose battery health and vehicle charging systems.
5.1 Battery Voltage Type Selection
After powering on the instrument, you can select the battery voltage type (6V, 12V, or 24V) using the navigation buttons.
5.2 Battery Test (Quick Test / Exact Test)
Once the battery is correctly connected, the tester will power on. Use the <▲> <▼> buttons to navigate the menu and <ENTER> to confirm selections.
- From the main menu, select "1. Start Ability" and press <ENTER>.
- Choose between "Quick Test" or "Exact Test" based on your needs.
- For Quick Test:
- The display will show "Set Bap Cap" (Set Battery Capacity). Use <▲> <▼> to adjust the AH value according to your battery's nameplate.
- Press <ENTER> to start the test.
- The test results will be displayed, including voltage, CCA, internal resistance (mΩ), and State of Health (SOH).
- For Exact Test:
- Select the battery standard (CCA, IEC, EN, DIN, JIS) using <▲> <▼> and press <ENTER>. For JIS, refer to the conversion table in Section 8.1.
- Adjust the battery specification value (e.g., CCA value) using <▲> <▼> buttons. Long press for faster adjustment.
- Press <ENTER> to start the test.
- The test results will be displayed, including voltage, CCA, internal resistance (mΩ), and State of Health (SOH).
Interpreting Battery Test Results:
- Battery Voltage: A normal 12V battery at full power is around 12.78V. Values below 12.12V indicate a fully discharged state.
- CCA Value: Higher CCA generally indicates better battery health. For 24V batteries, CCA is half the sum of the two 12V batteries in series.
- Internal Resistance (mΩ): Lower internal resistance is generally better. The standard varies by battery type and manufacturer. For 24V batteries, the internal resistance is the sum of the two 12V batteries in series.
- State of Health (SOH): Indicates the battery's remaining life. Replacement is recommended if SOH is below 45%.
5.3 Startup Load Test
This test evaluates the battery's performance during engine startup.
- Ensure the car is off and the ignition key is in the OFF position.
- Connect the tester clamps to the battery (red to positive, black to negative).
- From the main menu, select "2. Starting Load" and press <ENTER>.
- The tester will display static voltage and prompt you to start the car.
- Start the car. The tester will automatically record the minimum voltage during startup.
- If the lowest voltage is greater than 9.6V (for 12V systems), the startup system is good. If it's lower, there might be an issue with the starter, connections, or wiring.
5.4 Maximum Load Test
This test assesses the battery's ability to handle maximum electrical load.
- Start the car engine.
- Connect the tester clamps to the battery.
- From the main menu, select "3. Run Max Load" and press <ENTER>.
- The tester will instruct you to turn on all electrical loads (e.g., headlights, AC) and increase engine speed to 2000-2500 RPM.
- Press <ENTER> to proceed. The tester will display the current voltage and minimum voltage under load.
- If the voltage remains above 12.8V (for 12V systems), the system is normal. If it drops below, check the generator belt and wiring for issues.
5.5 Charging System Test
This test checks the vehicle's charging system (alternator).
- Start the car engine.
- Connect the tester clamps to the battery.
- From the main menu, select "4. Charging Test" and press <ENTER>.
- The tester will instruct you to increase engine speed to 2500-3500 RPM.
- Press <ENTER> to proceed. The tester will display the maximum, current, and minimum voltages.
- For a 12V system, the voltage should typically be between 13.30V and 15.00V. If the voltage is outside this range, check the voltage regulator, connections, or dynamotor.
5.6 Print Test Report (HT2018C only)
The HT2018C model supports printing test reports via Bluetooth. This feature allows you to record and check test results conveniently.
- After completing a battery test (e.g., startup test), the screen will remain on the test result interface.
- Press the middle button to enter the print test report interface.
- You will be prompted to enter the license plate number and test date/number. You can skip this by pressing <ESC> if you don't need to record this information.
- After setting up (or skipping), press <ENTER> to print or <ESC> to exit.
- Once printing is complete, the instrument will return to the battery startup test menu.
Note: A Bluetooth printer is required and is sold separately. Compatible models include XINYE XP-58IIH and Hejie XM-NAP-1 CB58B Bluetooth printers.
5.7 Language Selection
To change the language:
- Press <ESC> and <ENTER> buttons simultaneously while powering on the device.
- Alternatively, after powering on, press <ESC> and <ENTER> buttons for more than one second.
- The device will enter the language switching interface. Use <▲> <▼> buttons to select your desired language.
- Press <ENTER> to confirm the language and enter the test interface, or <ESC> to exit.
6. Maintenance
- Keep the instrument clean and dry. Wipe with a soft, damp cloth if necessary. Do not use abrasive cleaners or solvents.
- Store the instrument in a cool, dry place away from direct sunlight, high temperatures, high humidity, flammable or explosive materials, and strong electromagnetic fields.
- Regularly inspect the test clamps and cables for any signs of wear or damage. Replace if necessary to ensure safe and accurate operation.
- Do not attempt to open or repair the instrument yourself. Refer to qualified service personnel for any repairs.
7. Troubleshooting (Common Problems)
7.1 Measurement Principle of the Tester
Batteries degrade over time primarily due to aging of the battery plate, which reduces effective chemical reactions. The HT2018B/C uses a conductance test method, as recognized by the IEEE standard 1118-1996. This method involves applying a fixed frequency AC signal with a small current to the battery, sampling its voltage, and processing the data to calculate the internal resistance. This method is non-destructive and can measure almost all battery types, including small capacity batteries.
7.2 Reverse Current Affecting Test Results
Any reverse currents in the vehicle will affect the accuracy of the test results. To ensure precise measurements, remove any sources of reverse current before testing.
7.3 Predicting Battery Failure
The internal resistance of sealed lead-acid batteries is complex, influenced by ohmic resistance, concentration polarization, electrochemical reaction, and double-layer capacitor charging. While there's no strict mathematical relationship to predict exact service life, a sudden increase or decrease in internal resistance often indicates the battery is nearing the end of its life.
7.4 CCA Measurement Accuracy
CCA (Cold Cranking Amps) is a control standard for battery production. New batteries typically measure 10-15% higher than their labeled CCA value. As the battery is used, the measured CCA value will approach the labeled value, and eventually fall below it.
7.5 Comparison with Load Test Method
Traditional load tests (e.g., applying 40A-80A constant DC current) have limitations:
- Only suitable for large-capacity batteries.
- High currents can cause polarization resistance, leading to inaccurate readings if not measured very quickly.
- Large currents can damage battery electrodes.
The HT2018B/C's method avoids these issues by using a small, fixed-frequency AC current, making it safer and applicable to a wider range of batteries without causing damage.
8. Specifications
| Function | Range | HT2018B | HT2018C |
|---|---|---|---|
| Cold start current (CCA) | 100~1700 | √ | √ |
| Cold start current (IEC) | 100~1000 | √ | √ |
| Cold start current (EN) | 100~1700 | √ | √ |
| Cold start current (DIN) | 100~1000 | √ | √ |
| Cold start current (JIS) | 100~1700 | √ | √ |
| Battery internal resistance | 0.00mΩ~99.99mΩ | √ | √ |
| Battery Voltage | 4.5V~30V | √ | √ |
| X | √ | ||
| 6V, 12V, 24V battery test | √ | √ | |
| Startup load test | √ | √ | |
| Charging system test | √ | √ | |
| Maximum load test | √ | √ | |
| Prevent reverse function | √ | √ | |
| LCD | √ | √ | |
| The cable length | 600mm | 600mm | |
| Size | 143×77×28 (mm) | ||
| Weight | 270g | ||
9. Battery Specification Table
9.1 JIS Code Conversion Table
Use this table to convert JIS codes to CCA values for the Exact Test function.
Figure 5: JIS Code Conversion Table.
9.2 DIN/EN Model Comparison Table
Refer to this table for DIN/EN model comparisons.
Figure 6: DIN/EN Model Comparison Table.
10. User Tips
- Clean Terminals: Always ensure battery terminals are clean and free of corrosion for accurate readings.
- Stable Voltage: For best results, allow the battery voltage to stabilize after driving or charging before performing tests.
- Secure Connections: Double-check that the test clamps are securely attached to the correct battery terminals (red to positive, black to negative) to prevent false readings or damage.
- Environmental Conditions: Avoid testing in extreme temperatures, as this can affect battery performance and test accuracy.
- Regular Checks: Perform regular battery checks, especially before long trips or during seasonal changes, to prevent unexpected breakdowns.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the Hantek customer service directly. Keep your proof of purchase for warranty claims.
You can also refer to the official user manual PDF for more detailed information: Hantek HT2018B/C User Manual (PDF).