1. Introduction
This manual provides essential information for the safe and efficient use of your KNOA Switching Power Supply. This power supply is designed for various applications, including LED strips and other equipment requiring stable DC voltage. It features universal AC input, full load burn-in testing, and robust protection mechanisms.
2. Safety & Warnings
Please read all instructions carefully before use. Failure to follow these instructions may result in product damage or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
3. Setup
3.1 Input Voltage Selection
Before connecting the power supply, ensure the input voltage switch is set correctly for your region (110V or 220V). Incorrect selection can cause damage to the unit.
3.2 Wiring Instructions
Wire the power supply correctly according to the product diagram. Professional operation is required due to high voltage. Ensure all connections are secure.
- L, N: AC power input (Live and Neutral).
- GND: Ground wire.
- V-: DC power output negative terminal.
- V+: DC power output positive terminal.
4. Operation
4.1 Output Voltage Adjustment
The output voltage can be adjusted using the +V / ADJ potentiometer. This allows for fine-tuning the DC output within a certain range (typically ±10%).
4.2 Cooling Fan Operation
The power supply features a built-in temperature detector. The cooling fan will only activate when the internal temperature reaches approximately 113°F (45°C) to ensure efficient heat dissipation and quiet operation at lower loads.
4.3 Voltage and Current Control Demonstration
The power supply supports external control for voltage (0-24V) and current (0-21A) via 0-5V signals, allowing for integration with microcontrollers (e.g., single-chip microcomputers) or PLCs for applications like motor speed control, smart lighting adjustment, and charging. This provides linear control over the output.
5. Maintenance
- After use, turn off the device.
- Store the power supply in a dry place, away from children.
- Regularly inspect the unit for any signs of damage or wear.
6. Troubleshooting
- No Output Power: Check the input voltage switch (110V/220V) is correctly set. Verify AC input connections (L, N) are secure.
- Reduced Output Capacity: Ensure the power supply is not operating below its intended voltage range for the load. For example, operating at very low voltages (e.g., 0.7V) will significantly reduce its load capacity.
- Overheating: Ensure adequate air circulation around the unit. The cooling fan should activate at higher temperatures. If the fan does not operate, inspect for obstructions or malfunction.
- Unit Damage: Always ensure the input voltage is correctly selected before powering on. Connecting to an incorrect voltage (e.g., 110V when set to 220V) can cause immediate and irreversible damage.
7. Specifications
General Specifications:
- Input: AC110-220V 50/60Hz (Universal AC input / full range)
- Protections: Overload, Over Voltage, Short Circuit
- Cooling: Free air convection (temperature-controlled fan on some models)
- Working Temperature: 0~40 °C
- Storage Temperature: -20~60 °C
- Ambient Humidity: 0~95% Non-Condensation
- Safety Compliance: CCC / FCC / CE / RoHS
- Features: High price-effective, reliability with industry standards, 100% full load burn-in test.
Output Specifications:
| Output Voltage | Type (Output) | Size (LxWxH) | Input Voltage (AC) | Weight (kg) |
|---|---|---|---|---|
| DC 5V | 5V 2A 10W | 70x40x30mm | 85V-265V | 0.15 |
| 5V 4A 20W | 85x57x38mm | 85V-265V | 0.19 | |
| 5V 10A 50W | 110x78x36mm | 85V-265V | 0.3 | |
| 5V 20A 100W | 198x98x42mm | 85V-265V | 0.65 | |
| 5V 30A 150W | 198x98x42mm | 220VAC | 0.7 | |
| 5V 40A 200W | 200x110x50mm | 220VAC | 0.72 | |
| DC 12V | 12V 1A 12W | 70x40x30mm | 85V-265V | 0.12 |
| 12V 2A 24W | 85x57x38mm | 85V-265V | 0.19 | |
| 12V 3A 36W | 85x57x38mm | 85V-265V | 0.19 | |
| 12V 4A 50W | 110x78x36mm | 85V-265V | 0.28 | |
| 12V 5A 60W | 110x78x36mm | 85V-265V | 0.28 | |
| 12V 6.25A 75W | 110x78x36mm | 85V-265V | 0.30 | |
| 12V 8.3A 100W | 160x98x42mm | 85V-265V | 0.4 | |
| 12V 10A 120W | 160x98x42mm | 85V-265V | 0.4 | |
| 12V 12.5A 150W | 198x98x42mm | 85V-265V | 0.65 | |
| 12V 15A 180W | 198x98x42mm | 110V/220V±15% | 0.68 | |
| 12V 16.5A 200W | 200x110x50mm | 110V/220V±15% | 0.7 | |
| 12V 20A 250W | 200x110x50mm | 110V/220V±15% | 0.7 | |
| 12V 30A 360W | 215x115x50mm | 110V/220V±15% | 0.75 |
| Output Voltage | Type (Output) | Size (LxWxH) | Input Voltage (AC) | Weight (kg) |
|---|---|---|---|---|
| DC 24V | 24V 1A 25W | 85x57x38mm | 85V-265V | 0.15 |
| 24V 1.5A 35W | 85x57x38mm | 85V-265V | 0.18 | |
| 24V 2A 50W | 110x78x36mm | 85V-265V | 0.28 | |
| 24V 2.5A 60W | 110x78x36mm | 85V-265V | 0.28 | |
| 24V 4A 100W | 160x98x42mm | 85V-265V | 0.42 | |
| 24V 5A 120W | 160x98x42mm | 85V-265V | 0.45 | |
| 24V 8.3A 200W | 200x110x50mm | 110V/220V±15% | 0.7 | |
| 24V 10A 250W | 200x110x50mm | 110V/220V±15% | 0.7 | |
| DC 36V | 36V 5.5A 200W | 200x110x50mm | 110V/220V±15% | 0.7 |
| 36V 7A 250W | 200x110x50mm | 110V/220V±15% | 0.7 | |
| 36V 10A 360W | 215x115x50mm | 110V/220V±15% | 0.82 | |
| 36V 11A 400W | 215x115x50mm | 110V/220V±15% | 0.82 | |
| 36V 14A 500W | 215x115x50mm | 110V/220V±15% | 0.85 | |
| DC 48V | 48V 5A 250W | 200x110x50mm | 110V/220V±15% | 0.7 |
| 48V 7.5A 360W | 215x115x50mm | 110V/220V±15% | 0.8 | |
| 48V 8.3A 400W | 215x115x50mm | 110V/220V±15% | 0.8 | |
| 48V 10A 500W | 215x115x50mm | 110V/220V±15% | 0.85 | |
| 48V 12.5A 600W | 215x115x50mm | 110V/220V±15% | 0.9 |
8. User Tips
- This power supply is primarily suitable for LED strips. If you intend to use it with other equipment, it is recommended to contact customer service for compatibility and power supply recommendations.
- KNOA offers customized solutions for LED decoration. If you are unsure about matching components or what to purchase, reach out to customer service for assistance.
- Be aware that manual measurements may result in slight differences from the actual product dimensions.
- The power supply unit is generally quite large, so plan your installation space accordingly.
9. Warranty & Support
For any inquiries or support, please contact the manufacturer or their authorized representative:
- Manufacturer: SHENZHEN KNOA TECHNOLOGY CO., LTD.
- Address: Unit 1606, 1, Building B, Jida Garden, 38 Jinyun Road, Nansan Community, Buji Street, Longgang District, Shenzhen
- Email: 294411620@qq.com
- Telephone: +86 15889456615
- EU Authorized Representative: MJCM SARL
- EU Address: FR-78 avenue des Champs Elysees Bureau 326
- EU Email: mjcm190928@gmail.com
- EU Website/Telephone: +33 767213611
A detailed user manual in PDF format is available for download: View User Manual (PDF)